Veethree VeeCAN 320 User manual

High Exhaust System
Temperature (HEST) Lamp
TIER 4 ENGINE ONLY
VeeCAN 320
TM
Diesel Particulate Filter (DPF) Lamps
Glow Plug Lamp
Regeneration Inhibit Switch/Lamp
Diesel Particulate Filter Lamp
Diesel Exhaust Fluid level
Lamp (Not Equipped)
Check Engine Lamp
Stop/Check Engine Lamp
Consult On Screen Prompt & Engine Manual
To Determine Severity Of Fault
Note: Please refer to engine manual for further information regarding actions required for
ECM Controlled engines & Tier 4 engines.
LOW FUEL
Regeneration Level Lamp - Indicates Status Of Exhaust Temp. During
Passive Regen (R.LOW-R.MED-R.HIGH)
TIER 4 ENGINE ONLY
TIER 4 ENGINE ONLY
TIER 4 ENGINE ONLY
ECM CONTROLLED ENGINE ONLY
ECM CONTROLLED ENGINE ONLY
ECM CONTROLLED ENGINE ONLY

High Exhaust System
Temperature (HEST) Lamp
TIER 4 ENGINE ONLY
VeeCAN 320
TM
Diesel Particulate Filter (DPF) Lamps
Glow Plug Lamp
Regeneration Inhibit Switch/Lamp
Diesel Particulate Filter Lamp
Diesel Exhaust Fluid level
Lamp (Not Equipped)
Check Engine Lamp
Stop/Check Engine Lamp
Consult On Screen Prompt & Engine Manual
To Determine Severity Of Fault
Note: Please refer to engine manual for further information regarding actions required for
ECM Controlled engines & Tier 4 engines.
LOW FUEL
Regeneration Level Lamp - Indicates Status Of Exhaust Temp. During
Passive Regen (R.LOW-R.MED-R.HIGH)
TIER 4 ENGINE ONLY
TIER 4 ENGINE ONLY
TIER 4 ENGINE ONLY
ECM CONTROLLED ENGINE ONLY
ECM CONTROLLED ENGINE ONLY
ECM CONTROLLED ENGINE ONLY
Forced Regen Active -
RPM raises to 2000RPM
5-20minutes depending on
soot load
Soot level is above
limit - Park vehicle
and Perform forced
Regen
Soot Level -
low,med,high

in black text on a red background. Alarms already acknowledged are
shown in white text on black. If the engine hours data is available, the
list indicates when the alarm was initiated.
When first entering the alarm screen, the list automatically displays
the most recent alarm. The list can be scrolled using keys 1 and 2. This
screen cannot be exited until all the alarms have been acknowledged
by pressing key 3. Alarm messages are automatically cleared from the
list when no longer received by the VEM.
Alarm Screen
before Alarm Acknowledge
VeeCAN 320
TM
Alarm Screen
after Alarm Acknowledge
VeeCAN 320
TM
SPN 3719 - usually
indicates forced
Regen is required

MENU SCREENS
Top Level Menu
Settings Menu
and Sub-menus
VeeCAN 320
TM
VeeCAN 320
TM
VeeCAN 320
TM
VeeCAN 320
TM
VeeCAN 320
TM
VeeCAN 320
TM
VeeCAN 320
TM
VeeCAN 320
TM
To acces the Menu screens, press and
hold key 5 while in any of the display
screens. Pressing key 5 while in any of
the menus will return you to the previous
menu. PASSCODE: SEE DEALER/MFG
WARNING: DO NOT MODIFY PARAMETERS WITHOUT
AUTHERIZATION -WARRANTY WILL BE VOID
0810

System Menu and Sub-menus
VeeCAN 320
TM
VeeCAN 320
TM
VeeCAN 320
TM
Pin Settings are ued to prevent unathorized users to access the VEM
menu. The default pin number is “SEE DEALER/MFG”. Once the pin
is changed, the new pin becomes the only pin number that can be
used.
Note. If pin is changed, write down the pin in safe location.
Caution. If pin number is lost, a complete reload of the VEM software
using USB connection is required to access the menu. This reload will
rectore all default settings and any user changes made will be lost.
Factory Reset will reset all the settings to default values. This will also
reset the pin settings to the default pin number.
WARNING: DO NOT MODIFY PARAMETERS WITHOUT
AUTHERIZATION -WARRANTY WILL BE VOID

Tier 4 Engines
VeeCAN 320
TM
The VEM supports not only lamp informatin
for Tier 4 engines but also has the ability to
send CAN commands for Rorced Regen,
Regen Inhibit, and Auto eliminating the need
for the physical switch on the dash.
VeeCAN 320
TM
To access the T4 Control, go into Configuration
Menu, press Key 1 to scroll to T4 Control, than
press Key 4 to acess.
Key 1: Change the mode to Forced Regen.
Key 2: Change the mode to Auto.
Note. Auto is the default setting.
Key 3: Change the mode to Inhibited.
Key 5: Exit to Configutation Menu.
NOTE: Please refer to engine manual for further information reguarding
actions required for Tier 4 engines.
Forced Regen -
Hold until HEST
Lamp appears
If engine has other
faults, Regen may
not initiate
Find a safe
location, place in
neutral, apply
parking brake

Tier 4 Engines
VeeCAN 320
TM
The VEM supports not only lamp informatin
for Tier 4 engines but also has the ability to
send CAN commands for Rorced Regen,
Regen Inhibit, and Auto eliminating the need
for the physical switch on the dash.
VeeCAN 320
TM
To access the T4 Control, go into Configuration
Menu, press Key 1 to scroll to T4 Control, than
press Key 4 to acess.
Key 1: Change the mode to Forced Regen.
Key 2: Change the mode to Auto.
Note. Auto is the default setting.
Key 3: Change the mode to Inhibited.
Key 5: Exit to Configutation Menu.
NOTE: Please refer to engine manual for further information reguarding
actions required for Tier 4 engines.
Regen is default Auto - Passive Regen is
occurring in the background when the unit is
running above idle RPM - avoid excessive
idle to prevent premature soot build up