veise KS02A User manual

KS02A
Keypad Digital Deadbolt
Installation Guide / Programming Instructions
Thank you for purchasing our products. Please review this manual thoroughly before operating your device.
All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.

Installation Overview Programming Instructions
STEP 1: Prepare the door and check dimensions
STEP 2: Install the latch and strike
STEP 3: Install exterior assembly
STEP 4: Install interior assembly
STEP 5: Detect left/right hand door installation
P 3
P 4
P 6
P 7
P 8
P 9
P10
P 11
P 12
P 13
At a Glance
How to Use
Definitions
Code Format
Quick Set Up
P 15
P16
P17
Factory Default Settings
Troubleshooting
Information & Safety Warnings
IMPORTANT:
TOOL REQUIRED:
Do not use an electric
screwdriver during installation.
Do not load batteries until lock is
completely installed.

INSTALLATION OVERVIEW
1
Strike Screws
(H)
Interior Assembly
Screws (K)
Strike (D)
Backup key (A)
Mounting
plate Screws (J)
Battery
Cover (G)
Mounting
plate (E)
Interior
Assembly (F)
Exterior Assembly
(B)
Latch (C)
Latch Screws
(I)
Reinforcement
plate (D-1)

Latch x1
Drive-In Collar (Optional)
Strike x1
Exterior Assembly x1
Mounting Plate x1 Interior Assembly x1 Battery Cover x1 Strike Screws x4
Mounting plate Screws x2 Interior Assembly
Screws x3
Latch Screws x2
A B C
E F G
L
H
I
J K
D
Reset Tool x1 M
Parts List
If any parts are missing or damaged, please contact Customer Support.
2
Backup Key x2
Reinforcement
Plate x1
(optional)

Measure to confirm
that the hole in the
door edge is 1"
(25mm).
Measure to confirm
that the backset is
either 2-3/8" or
2-3/4" (60 or 70mm)
2-3/8" or 2-3/4"
(60 or 70mm)
Make sure the hole in
door frame is drilled a
minimum of 1"
(25mm) deep.
Measure to confirm
that the door is 1-3/8"
to 2" (35 mm or
50mm) thick.
A
Measure to
confirm that the
hole in the door is
2-1/8" (54mm).
B
CD
Prepare the door and check dimensions
1
STEP
3
1"
25mm
1-3/8" to 2"
(35mm or 50mm)

4
chiseled
not chiseled
Drive-In Collar
(B)
Install the latch and strike
2
STEP
Hold the latch in front of the door hole,
with the latch face flush against the
door edge. Is the slotted hole centered
in the door hole?
No adjustment is required.
Proceed to next step.
Slotted hole is
NOT centered.
A
B
YES
NO
Rotate and pull the
latch as shown to
extend latch.
2-3/4"
(70mm)
2-3/8"
(60mm)
pull
Determine backset
and adjust the latch
Install the latch
Latch Screws (I)
up

CUse a screwdriver to test if
deadbolt works smoothly.
DInstall strike on the door frame. Make sure the hole in door frame is
drilled a minimum of 1" (25mm)
deep.
IMPORTANT:
5
D
(Optional)

AB
Mounting plate Screws(J)
Keep parallel to
door edge.
Install exterior assembly
3
STEP
Unlocked
Before installation, make sure the latch is
fully retracted (in the unlocked position)
IMPORTANT:
Locked
With the latch fully retracted (in the unlocked
position), route the cable below the latch, and
insert the tourque blade through the slot in the
latch. 6
Tourque
blade
Secure the mounting plate with the
supplied screws. Do not overtighten
screws.

C
Unlocked
Keep the thumb turn in vertical position and install
the interior assembly.
Install interior assembly
4
STEP
Do not load batteries until lock is
completely installed.
IMPORTANT:
Push the battery cover out in
the direction as illustrated.
Insert the cable
connector to the
socket. Push the
connector in firmly
until it is completely
attached.
Attach Interior
Assembly to
Mounting Plate and
tighten 3 Screws.
A B
D
7
Horizontal
Interior Assembly
Screws (K)

While the door is OPEN and
UNLOCKED, load 3 AA batteries
into the battery compartment.
Note:
For long last, please use all new,
non-rechargeable Alkaline
batteries only.
Press and hold the Reset button on
the interior assembly by using the
reset tool.
This step is required and crucial for the lock
to operate properly.
IMPORTANT:
Detect left/right hand door installation
5
STEP
Reset the lock to teach the lock the orientation of the door.
A B Load the 4th battery and keep holding
the reset button for 3 seconds, until
you hear the sound of "beep". The
latch bolt will extend to learn the
orientation of the door automatically.
C
8
Reset button
Unlocked

PROGRAMMING INSTRUCTIONS
At a Glance
Exterior Assembly Interior Assembly
9
Keypad
Fingerprint
Keyhole
Multi-Function
Button(MFB) Battery Cover
Reset Button
Thumb Turn

How to Use
UNLOCK the door from outside
or
LOCK the door from outside
Master code + User code +
Auto Lock Mode
In Auto Lock mode, the bolt
will extend out automatically in
30 seconds after unlocking.
Manual Mode
Press any key on keypad for
2 seconds.
UNLOCK the door from inside
LOCK the door from inside
Auto Lock Mode
In Auto Lock mode,
the device will be
locked automatically.
Rotate the thumb turn to
Unlock position.
Manual Mode
Rotate the thumb turn to Lock Position.
10
or

• Master Code
Required for programming and feature settings. Master code can be
used to unlock the door under vacation mode. The default master
code needs to be changed before programming.
Property owner & manager should keep this information confidential.
• Auto Lock
Automatically locks the deadbolt 30 seconds after unlocking. This
feature is off by default. You can customize the Auto Lock time delay
between 10 and 99 seconds.
• Key Unlock
Key Unlock is always available when the batteries are completely
dead or valid User Codes are forgotten.
• Low Battery Indicator
If you hear 10 beeps along with 10 red light flashing after pressing
any key to lock or unlock the door, that’s an alert for replacing
batteries. Please replace with 4 brand new AA alkaline batteries and
do not mix used and new batteries. All settings are stored in the lock
while the batteries are removed and replaced.
• Wrong Entry Limit
After 10 unsuccessful attempts at entering an invalid PIN code, the
unit will shut down for 3 minutes.
• Silent Mode
The beep sounds when pressing keypad can be muted. But you will
still hear low battery and system alerts.
• Vacation Mode
This is a security feature for you when you are leaving your home for
vacation or long trip. Enabling vacation mode will restrict all user
codes until master code is entered on keypad. If the lock would be
unlocked by the thumb turn from the inside, the lock will sound an
alarm.
• One Time User Code
This code only can be used once and will be automatically deleted
after used.
• Unlock with Fake code
User can prevent pin code exposure from strangers by entering
random digits before or after pin code.
Definitions Programming Basic
11

1. Master Code(4 to 10 digits): The default Master Code is 12345678. It is required that you change it to a code of your own before
programming.
2. User Code: 20 User Codes (4-10 digits), 1 one-time User Code and 20 fingerprints can be programmed and stored in the lock.
3. Both Master Code and User Code don’t support the following combination of numbers.
Forward number sequence
Backward number sequence
Repeat number sequence
Contain existing code sequence
Programming BasicCode Format
12

Quick Set Up
+ Master Code +
Wait for long green lights
Change
Master Code
Press 1
Wait for green light flash Succeed
Green light flash
Wait for green light flash
New Master Code + New Master Code +
+ Master Code +
Wait for long green lights
Add
User Code
Press 2
Wait for green light flash Succeed
Green light flash
Wait for green light flash
New User Code + New User Code +
+ Master Code +
Wait for long green lights
Delete
User Code
Press 3
Succeed
Green light flash
Wait for green light flash
Unwanted User Code +
Add
Fingerprint
+ Master Code +
Wait for long green lights
Press 4
Succeed
Green light flash + A long beep
Wait for green light flash
Scan fingerprint 8 times
Each time succeed along with a short beep
Delete
Fingerprint
+ Master Code +
Wait for long green lights
Press 5
Succeed
Green light flash + A long beep
Wait for green light flash
Scan unwanted fingerprint 1 time
13
The default Master Code is 12345678 .
It is required that you change it to a code of
your own before programming.
IMPORTANT:

14
Master Code +
Disabled
Vacation
Mode Vacation Mode Disabled
The door was opened
Set Auto
Lock Time
+ Master Code + Press 0Enter New Duration Time
(10-99)
+
Wait for long green lights Wait for green light flash Succeed
Green light flash
Auto Lock
Wait for long green lights Wait for green light flash Auto Lock Disabled
Green light flash
+
+ Master Code + Auto Lock Enabled
Green light flash
+
Press 7
Add
One-Time
Code Wait for long green lights Wait for green light flash Wait for green light flash Succeed
Green light flash
+ Master Code + New User Code + New User Code +
Press 9
Enable
Vacation
mode Wait for long green lights Wait for green light flash Vacation Mode Enabled
Green light flash
+ Master Code + Press
Press 8
Silent
Mode
+ Master Code + Press 6Silent Mode Disabled
Green light flash
1
Wait for long green lights Wait for green light flash Silent Mode Enabled
Green light flash
2
1
2
1. Beeps only sound when the Silent Mode is disabled.
2. If the indicators flash red light, it means your setting failed and it will require to re-enter master mode if you would like to continue
your programming.
Notes:

Factory Default Settings
The resetting will delete all User Codes stored
in the lock.
IMPORTANT:
How to Reset?
Step 1. Keep the door open and unlocked.
Step 2. Press and hold the Reset button, at the same time take out one
battery and then place it back.
Step 3. Keep holding the Reset button for 3 seconds, until you hear the
sound of "beep" and the latch will extend automatically.
Settings
Master Code
Auto Lock
Silent Mode
Wrong Code Entry Limit
Shutdown Time
Vacation Mode
Factory Defaut
12345678
Disabled
Disabled
10 times
3 mins
Disabled
15
Reset button

Troubleshooting
Why does not the latch extend but the motor is rotating when
resetting my lock?
Improper installation may have caused the issue. Please follow the
steps to review:
1. Please make sure the latch and strike are aligned.
2. Please slightly loosen the mounting screws on the external
assembly keypad and the latch bolt if the screws are over-tightened.
3. Please open your door and reset the lock.
Why does not the latch extend and the motor isn't rotating
when resetting my lock?
The deadbolt latch should be retracted(unlocked) through all your
installation process.
The thumb turn should be vertical in your installation steps 4C and 5A.
Please open your door and reset the lock.
When I attempt to lock/unlock my deadbolt, why does the
latch go in and out for a few times?
It happens when the latch and strike are misaligned.
Please make sure the bolt hole on the door frame is at least 1 inch
deep, so that the bolt can be fully extended.
Please check if the door can be closed properly, the deadbolt should not
impact the strike or door frame on the door frame side, it should go
directly into the hole properly.
Why does my lock only work properly when the backup key is
in? Why am I unable to pull the key out in the unlocked
position?
You may need to re-install the whole lock.
Please make sure when you start to install, the lock is in unlocked
status;
Please make sure the thumb turn is vertical.
Please do not put the backup key in the lock.
What does 5 short and fast beeps mean while programming?
It alerts you either time-out or wrong entry.
Please be sure to complete each setting step within 5 seconds.
Please change the default master code in the first time programming.
Please be sure the user code is with correct format and with 4 to 10
digits.
What if I forget my Master Codes?
If you forget your Master code, resetting your lock, then the original
master code (12345678) works, and all previous user codes were
erased.
16

• Protect your User Codes and Master Code.
• Restrict access to your lock’s interior assembly and routinely check your
settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by
itself.
• This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and
common sense.
• Care should be taken to ensure a long-lasting finish. When cleaning is
required use a soft, damp cloth. Using lacquer thinner, caustic soaps,
abrasive cleaners or polishes could damage the coating and result in
tarnishing.
• The lock is water resistant. It can withstand water splashes; however, do
not let water and liquids get into the lock.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight
may damage the lock.
Information & Safety Warnings
17
Table of contents
Other veise Lock manuals
Popular Lock manuals by other brands

Simons Voss Technologies
Simons Voss Technologies Z4.PL quick guide

KAWNEER
KAWNEER 1786 installation instructions

Wittkopp
Wittkopp SmartCam user manual

Sentrilock
Sentrilock GENI quick start guide

Burg
Burg Flexo.Code operating manual

Assa Abloy
Assa Abloy SARGENT 115 Hospital Latch installation instructions

MARKS USA
MARKS USA iQ Wik Data Series Quick Set-Up Programming Guide

Digital Home System
Digital Home System DH210 instruction manual

Panduit
Panduit smartzone G5 installation guide

prudhomme
prudhomme SPX4 Series Installation and maintenance sheet

ZKTeco
ZKTeco DL30B installation guide

SECO-LARM
SECO-LARM Enforcer E-941SA-300 installation manual