Velleman DVM892N User manual

DVM892N
CAT. II 700 V / CAT. III 600 V
USER MANUAL 3
HANDLEIDING 16
MODE D'EMPLOI 29
MANUAL DEL USUARIO 43
BEDIENUNGSANLEITUNG 56
INSTRUKCJA OBSŁUGI 70
MANUAL DO UTILIZADOR 84

DVM892N
V. 03 –19/08/2021 2 ©Velleman Group nv

DVM892N
V. 03 –19/08/2021 3 ©Velleman Group nv
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal
of the device after its lifecycle could harm the environment. Do
not dispose of the unit (or batteries) as unsorted municipal
waste; it should be taken to a specialized company for recycling.
This device should be returned to your distributor or to a local
recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before
bringing this device into service. If the device was damaged in transit, do
not install or use it and contact your dealer.
2. Used Symbols
AC (Alternating Current)
DC (Direct Current)
Both AC and DC
Risk of Electric shock. A potentially hazardous voltage is
possible.
Caution: risk of danger, refer to the user manual for safety
information.
Warning: a hazardous condition or action that may result in
injury or death
Caution: condition or action that may result in damage to the
meter or equipment under test
Double insulation (class 2-protection)
Earth
Fuse
Capacitor
Diode

DVM892N
V. 03 –19/08/2021 4 ©Velleman Group nv
Continuity
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages
of this manual.
This symbol indicates: Read instructions
Not reading the instructions and manual can lead to damage,
injury or death.
This symbol indicates: Danger
A hazardous condition or action that may result in injury or
death
This symbol indicates: Risk of danger/damage
Risk of a hazardous condition or action that may result in
damage, injury or death
This symbol indicates: Attention; important information
Ignoring this information can lead to hazardous situations.
WARNING: To avoid electrical shock always disconnect the
test leads prior to opening the housing. To prevent fire hazards,
only use fuses with the same ratings as specified in this manual.
Remark: refer to the warning on the battery compartment
Avoid cold, heat and large temperature fluctuations. When
the unit is moved from a cold to a warm location, leave it
switched off until it has reached room temperature. This to
avoid condensation and measuring errors.
Protect this device from shocks and abuse. Avoid brute force
when operating.
Pollution degree 2-device. For indoor use only. Keep this device
away from rain, moisture, splashing and dripping liquids. Not for
industrial use. Refer to §8 Pollution degree.
Keep the device away from children and unauthorised users.
Risk of electric shock during operation. Be very careful
when measuring live circuits.

DVM892N
V. 03 –19/08/2021 5 ©Velleman Group nv
There are no user-serviceable parts inside the device.
Refer to an authorized dealer for service and/or spare parts.
This is an installation category CAT III measuring
instrument. Refer to §7 Overvoltage/installation category.
Read this addendum and the manual thoroughly. Familiarise
yourself with the functions of the device before actually using it.
All modifications of the device are forbidden for safety reasons.
Damage caused by user modifications to the device is not
covered by the warranty.
Only use the device for its intended purpose. Using the device in
an unauthorized way will void the warranty. Damage caused by
disregard of certain guidelines in this manual is not covered by
the warranty and the dealer will not accept responsibility for any
ensuing defects or problems.
WARNING –To avoid electric shock, fire or personal injury:
•Connect the common test lead before the live test lead and
remove the live test lead before the common test lead.
•Disconnect the power and discharge all high-voltage
capacitors before you measure resistance, continuity,
capacitance or a diode junction.
•When using the temperature probe, do not connect the probe
to live circuits.
4. Maintenance
There are no user-serviceable parts inside the device.
Refer to an authorized dealer for service and/or spare parts.
Before performing any maintenance activities, disconnect the test leads
from the jacks.
For instructions on replacing battery or fuse, refer to §11 Battery and fuse
replacement.
Do not apply abrasives or solvents to the meter. Use a damp cloth and mild
detergent for cleaning purposes.
5. During Use
Risk of electric shock during operation. Be very careful when
measuring live circuits.
•Never exceed the limit value for protection. This limit value is listed
separately in the specifications for each range of measurement.
•Do not touch unused terminals when the meter is linked to a circuit
which is being tested.

DVM892N
V. 03 –19/08/2021 6 ©Velleman Group nv
•Never use the meter with CAT II installations when measuring voltages
that might exceed the safety margin of 700 V above earth ground.
Never use the meter with CAT III installations when measuring voltages
that might exceed the safety margin of 600 V above earth ground.
•Set the range selector at its highest position if the intensity of the
charge to be measured is unknown beforehand.
•Disconnect the test leads from the tested circuit before rotating the
range selector in order to change functions.
•When carrying out measurements on a TV set or switching power
circuits, always remember that the meter may be damaged by any high
amplitude voltage pulses at test points.
•Always be careful when working with voltages above 60 VDC or 30 VAC
rms. Keep your fingers behind the probe barriers at all times during
measurement.
•Never perform resistance, diode or continuity measurements on live
circuits. Make sure all capacitors in the circuit are depleted.
6. General Description
Refer to the illustration on page 2 of this manual:
1. Display
3 ½ digits, 7 segments, LCD: 61 x 26 mm
2. On-off
3. Rotary switch
This switch is used to select functions and desired ranges as well as to
turn the meter on/off.
4. Hold button
In any range, press this button to freeze the last reading. Press again
to unfreeze.
5. "15A" jack
Insert the red test lead in this connector in order to measure a max.
current of 15 A.
6. "mA/BATT/°C" jack
Insert the red test lead in this connector in order to measure current
(except 15 A), the battery and temperature.
7. "COM" jack
Insert the black (negative) test lead.
8. "V" jack
Insert the red (positive) test lead in this connector to measure voltage
and resistance.
7. Overvoltage/Installation Category
DMMs are categorized depending on the risk and severity of transient
overvoltage that might occur at the point of test. Transients are short-lived

DVM892N
V. 03 –19/08/2021 7 ©Velleman Group nv
bursts of energy induced in a system, e.g. caused by lightning strike on a
power line.
The existing categories according EN 61010-1 are:
CAT I
A CAT I-rated meter is suitable for measurements on protected
electronic circuits that are not directly connected to mains power,
e.g. electronics circuits, control signals…
CAT
II
A CAT II-rated meter is suitable for measurements in CAT I-
environments and mono-phase appliances that are connected to the
mains by means of a plug and circuits in a normal domestic
environment, provided that the circuit is at least 10 m apart from a
CAT III- or 20 m apart from a CAT IV-environment. E.g. household
appliances, portable tools…
CAT
III
A CAT III-rated meter is suitable for measurements in CAT I- and
CAT II-environments, as well as for measurements on (fixed) mono-
or poly-phased appliances which are at least 10 m apart from of a
CAT IV-environment, and for measurements in or on distribution
level equipment (fuse boxes, lighting circuits, electric ovens).
CAT
IV
A CAT IV-rated meter is suitable for measuring in CAT I-, CAT II-
and CAT III-environments as well as on the primary supply level.
Note that for all measurements on equipment for which the supply
cables run outdoors (either overhead or underground) a CAT IV
meter must be used.
Warning:
This device was designed in accordance with EN 61010-1 installation
category CAT II 700 V and CAT III 600 V. This implies that certain
restrictions in use apply that are related to voltages and voltage peaks
which can occur within the environment of use. Refer to the table above.
This device is only suitable for measurements up to 700 V in
CAT II and up to 600 V in CAT III
8. Pollution Degree
IEC 61010-1 specifies different types of pollution environments, for which
different protective measures are necessary to ensure safety. Harsher
environments require more protection, and the protection against the
pollution which is to be found in a certain environment depends mainly on
the insulation and the enclosure properties. The pollution degree rating of
the DVM indicates in which environment the device may be used.
Pollution
degree 1
No pollution or only dry, nonconductive pollution occurs. The
pollution has no influence. (only to be found in hermetically
sealed enclosures)

DVM892N
V. 03 –19/08/2021 8 ©Velleman Group nv
Pollution
degree 2
Only nonconductive pollution occurs. Occasionally,
temporary conductivity caused by condensation is to be
expected. (home and office environments fall under this
category)
Pollution
degree 3
Conductive pollution occurs, or dry nonconductive pollution
occurs that becomes conductive due to condensation that is
to be expected.
(industrial environments and environments exposed to
outside air - but not in contact with precipitation)
Pollution
degree 4
The pollution generates persistent conductivity caused by
conductive dust or by rain or snow. (exposed outdoor
environments and environments where high humidity levels
or high concentrations of fine particles occur)
Warning: This device was designed in accordance with EN 61010-1
pollution degree 2. This implies that certain restrictions in use apply that
are related to pollution which can occur within the environment of use. Refer
to the table above.
This device is only suitable for measurements in Pollution
degree class 2 environments.
9. Specifications
This device is not calibrated when purchased!
Regulations concerning environment of use:
Use this meter only for measurements in CAT I, CAT II and CAT III
environments (see §7)
Use this meter only in a pollution degree 2 environment (see §8)
Ideal working conditions include:
temperature: 0 °C to 40 °C (32 °F to 104 °F)
relative humidity: max. 80 %
altitude: max. 2000 m (6560 ft)
voltage ........................................................................... 700 V
fuse protection
F500 mA/1000 V, 6 x 32 mm
F15 A/1000 V, 6 x 32 mma
power supply ........................................... 1 x 9 VDC 6LR61 (incl.)
display............................................................ LCD, 1999 counts
display dimensions ...................................................61 x 26 mm
over-range ..........................................................................yes
continuity buzzer..................................................................yes
transistor test ....................................................................... no
diode test............................................................................yes
low-battery indication ...........................................................yes

DVM892N
V. 03 –19/08/2021 9 ©Velleman Group nv
ranging mode ................................................................ manual
data hold ............................................................................yes
backlight.............................................................................. no
auto power-off .....................................................................yes
dimensions..................................................... 165 x 85 x 37 mm
weight (with battery) ..................................................... ± 215 g
storage environment
temperature ................................................. -20 °C to 60 °C
humidity ............................................................ < 90 % RH
test lead probe (incl.)..................... CAT III 600 V, 15 A; L = 80 cm
9.1 DC VOLTAGE
Do not measure circuits that may contain voltages
> 700 V
range
resolution
accuracy
200 mV
0.1 mV
± (0.5 % rdg + 2 digits)
2000 mV
1 mV
20 V
10 mV
200 V
100 mV
700 V
1 V
± (0.8 % rdg + 2 digits)
Overload protection: 700 V DC or AC rms
Impedance: 10 MΩ
9.2 AC VOLTAGE
Do not measure circuits that may contain voltages
> 700 V
range
resolution
accuracy
2000 mV
1 mV
± (0.8 % rdg + 3 digits)
20 V
10 mV
200 V
100 mV
700 V
1 V
± (1.2 % rdg + 3 digits)
Average sensing, calibrated to rms of sine wave
Frequency range: 40-500 Hz
Overload protection: 700 V DC or AC rms
Impedance: 10 MΩ

DVM892N
V. 03 –19/08/2021 10 ©Velleman Group nv
9.3 DC CURRENT
Do not measure circuits that may contain voltages
> 700 V
range
resolution
accuracy
2 mA
1 µA
± (1.2 % rdg + 2 digits)
20 mA
10 µA
200 mA
100 µA
± (1.5 % rdg + 2 digits)
15 A
10 mA
± (2.0 % rdg + 3 digits)
Overload protection: F500 mA/1000 V, F15 A/1000 V fuse
Note: 15 A up to 10 seconds
9.4 AC CURRENT
Do not measure circuits that may contain voltages
> 700 V
range
resolution
accuracy
2 mA
1 µA
± (1.5 % rdg + 3 digits)
20 mA
10 µA
200 mA
100 µA
± (2.0 % rdg + 3 digits)
15 A
10 mA
± (2.5 % rdg + 5 digits)
Average sensing, calibrated to rms of sine wave
Frequency range: 40-500 Hz
Overload protection: F500 mA/1000 V, F15 A/1000 V fuse
Note: 15 A up to 10 seconds
9.5 RESISTANCE
Do not conduct resistance measurements on live
circuits
range
resolution
accuracy
200 Ω
0.1 Ω
± (1.0 % rdg + 3 digits)
2 kΩ
1 Ω
± (1.0 % rdg + 2 digits)
20 kΩ
10 Ω
200 kΩ
100 Ω
2 MΩ
1 kΩ
20 MΩ
10 kΩ
± (1.5 % rdg + 3 digits)
Overload protection: 700 V DC or AC rms