Velux ZMT 300 User manual

ZMT 300
Instructions For
The Motorized Control Rod
WARNING: When using electric tools, basic safety precautions
should always be followed to reduce the risk of fire, electric shock,
and personal injury:
1) Do not store or carry battery so that metal objects can contact
exposed metal end. For example, do not place battery in aprons,
pockets, tool boxes, drawers, etc. with loose nails, screws, keys, etc.
Battery could short circuit causing fire, burns or damage to battery.
2) Never attempt to open the battery for any reason. If the
housing of the battery breaks or cracks, discontinue use
immediately and do not recharge.
3) Do not incinerate the battery; it can explode in a fire. Leakage
of liquid from batteries can occur if damaged. If the outer seal
is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with
clean water for a minimum of 10 minutes and seek
immediate attention.
MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.
4) Charge batteries with VersaPak battery charger. Charger
recharges batteries in approximately three hours. Remove
battery charger from the outlet after charging.
5) Do not use charger in wet or damp conditions. It is intended
for indoor use only. Do not use near sinks, tubs, etc. Do not
immerse in water.
6) Do not use charger for any uses other than charging
VersaPak Batteries. Other batteries may explode.
7) Do not operate charger with damaged cord or plug.Have
them replaced immediately.
8) Do not operate charger if it has received a sharp blow, been
dropped, or otherwise damaged in any way.
9) Do not disassemble charger. Incorrect reassembly may result
in electric shock or fire. There are no consumer serviceable
parts inside.
10) For best results, do not charge batteries when they or the air
temperature is below 40°F or above 105°F.
11) The charger is designed to operate on standard household
electrical power (120 volts AC only). Do not attempt to use it
on any other voltage.
12) Unplug charger when not in use.
13) Do not abuse charger cord. To reduce the risk of damage to
electric plug and cord, never carry charger by cord or roughly
pull it to disconnect from receptacle. Keep charger cord from
heat, oil, and sharp edges.
IMPORTANT SAFETY INSTRUCTIONS

Removing and Installing Battery
NOTE: VERSAPAK‰ Batteries are not fully charged at the factory.
To install the battery into the ZMT 300, simply slide it into the
handle until it clicks into place. To remove the battery, press the
release button and pull.
Switch
To turn the ZMT 300 ON in a forward direction, slide the switch
button to the right and align it with the arrow pointing forward.
Depress the switch button and the ZMT 300 will run. Release the
button and the rod will stop.
To operate in reverse, slide the switch button to the left and align it
with the arrow pointing backward. Depress the switch button and the
ZMT 300 will run. Release the button and the rod will stop.
Cleaning
Use only mild soap and damp cloth to clean the tool. Do not immerse
any part of the ZMT 300 into water or let water get inside.
The RBRC Seal
The RBRC‰ (Rechargeable Battery Recycling Corporation) Seal on
the nickel-cadmium battery (or battery pack) indicates that the
costs to recycle the battery at the end of its useful life has already
been paid. In some areas it is illegal to place spent nickel-cadmium
batteries in the trash or municipal solid waste stream. The RBRC
program provides an environmentally conscious alternative.
VELUX America Inc. 1-800-88-VELUX VELUX Canada Inc.
V-USA-0726-0906 2006 VELUX GROUP www.veluxusa.com VELUX, VELUX logo are registered trademarks of VELUX Group