Vent-Axia 563515A User manual

Stock Ref
563515A
7 Day TimeSwitch
Fitting & Wiring Instructions
PLEASE RETAIN THESE INSTRUCTIONS WITH THE PRODUCT.
220-240V ~ 50Hz

2
VENT-AXIA 7 DAY TIMESWITCH MAINS 220-240V FITTING AND WIRING INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION
Contents:-
1. Set the timer
2. Manual override
3. Installation guide
4. Specification
1.Set the Timer
Do not rotate the dial anti-clockwise as this will damage the mechanism.
Rotate the minute hand clockwise until the arrowhead on the clock face aligns with the
correct time on the outer dial. See Fig.1.
Align the correct time on the outer dial, within the current
day sector dial.
Please note: The week days are printed around the edge
of the dial in abbreviations of three languages.
To set ON/OFF times, move the tappets between ON
and OFF times required to the outer edge of the dial.
See Fig.1. to set ON at 6:00 a.m. and OFF at 12.00 a.m.
move all tappets to outer position between 6:00 a.m and
12:00 on the dial.
Set any other ON/OFF times in a similar manner.
Minimum switching on the 7 day timeswitch is 2 hours.
2. Manual Override
There is a three position manual selector built-in to the clock dial face.
See Fig.2.
Leave the selector in the middle position for automatic control, when the
output is ON of OFF according to the tappet settings. To switch ON
manually, move the selector to position 1 (marked I on the dial). To
switch OFF manually, move the selector to position 3 (marked 0 on the
dial).
The manual lever is a fixed selection. The output will stay as selected
until the manual lever is moved once more.
Tappets in
OFF position Tappets in
ON position
Fig.1.
1 = ON
2 = AUTO
3 = OFF
1
2
3
Fig.2.

3
3.Installation guide
Installation must be carried out in accordance with the current edition of the I.E.E wiring
regulations. It is recommended that installation is undertaken only by a qualified electrician.
Undo the recessed cross-head screws. Grip the square timer housing and pull the timer
away from the base.
If required the square timer can be panel mounted by use of the plastic lugs top left / bottom
right (push and turn with a flat bladed screwdriver to secure to panel).
If surface mounting, drill the wall to suit the threebackplate mounting holes. Secure to wall
surface using suitable wall plugs & screws.
If din-rail mounting, hook the backplate to the din-rail and push into place until the red clip
clicks behind the lower edge of the rail.
Connect wiring according to the wiring diagram
Live & Neutral to terminals 1 & 2 (The device is not polarity
conscious). Terminals 3,4 & 5 are volt-free switch
3 = common, 4 = normally open, 5 = normally closed.
For mains switching, connect live 3, fit a short link wire between 3 & 2 . Connect incoming
and outgoing meutrals to terminal 1. Connect the load switched live, to terminal 4.
Do not connect any conductor to 5. If there is an earth continuity conductor, make separate
provision to connect incoming / outgoing earth wires. The timer is double insulated.
Fit the terminal cover to the backplate, push the square timer onto the base. Tighten the
cross-head screws. Fit the dust cover.
4.Specification
Motor: 220-240V AC 50Hz
Temperature rating: T45
Switch type: changeover
Rating: 16A resistive / 8A inductive
Not suitable for direct switching of lighting types:- Fluorescent, HID, SON, LED
Use a contactor for discharge lamps
Class II control / Protection class IP20
Complies with European Norm EN 60730-1:2011
Automatic Electrical Controls for Household and similar use,
and European Directives: LVD; EMC; RoHS

4
The Guarantee
Applicable only to products installed and used in the United Kingdom. For details of guarantee outside the United Kingdom contact your local
supplier.
Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship. In the event of any part being found
to be defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:-
Has been installed and used in accordance with the instructions given with each unit.
Has not been connected to an unsuitable electricity supply. (The correct electricity supply voltage is shown on the product rating label
attached to the unit).
Has not been subjected to misuse, neglect or damage.
Has not been modified or repaired by any person not authorised by the company.
IF CLAIMING UNDER TERMS OF GUARANTEE
Please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by post or personal visit. Please ensure
that it is adequately packed and accompanied by a letter clearly marked “Guarantee Claim” stating the nature of the fault and providing evidence of
date and source of purchase.
The guarantee is offered to you as an extra benefit, and does not effect your legal rights
abc
Head Office: Fleming Way, Crawley, West Sussex, RH10 9YX. Tel: [phone] Fax: [phone]
UK NATIONAL CALL CENTRE, Newton Road, Crawley, West Sussex, RH10 9JA
SALES ENQUIRIES: Tel: [phone] Fax: [phone]
TECHNICAL SUPPORT: Tel: [phone] Fax: [phone]
Web:-www.vent-axia.com Email:- [email protected]
As part of the policy of continuous product improvement Vent-Axia reserves the right to alter specifications without notice.
478403A 0518