venture horizon 2380 User manual

SPARTAK ENTERPRISES, INC.
SWIVEL MEDIA TOWER
Model #2380-33OA
LOT #2639
IF PARTS ARE MISSING AND OR DEFECTIVE, IF INSTRUCTIONS ARE NOT CLEAR
OR IF YOU ARE EXPERIENCING PROBLEMS ASSEMBLING OUR PRODUCT.
BEFORE YOU RETURN THE PRODUCT TO THE STORE,
PLEASE CALL US TOLL FREE FOR CUSTOMER SERVICE ASSISTANCE
[phone]
OR SEND US EMAIL AT
[email protected]
PLEASE HAVE ITEM NUMBER READY, AND A REPRESENTATIVE WILL GLADLY ASSIST YOU
SPARTAK ENTERPRISES, INC. 841 E. FRANCIS STR. ONTARIO, CA. 91761 TEL; 951/360-0610 FAX; 951/360-0775

CCPZXX
CAMLT12
CAMBT16
BM25
SPE610BL
BP--54
TRNTPL
TRNTSC
DOWW830
CAMLOCK COVER CAP
CAMLOCK
BOLT
BRACKET ANGLE
EURO SCREW
SHELF SUPPORT
SWIVEL PLATE
SWIVEL BOLT
WOOD DOWEL
HARDWARE PART # DESCRIPTION QTY
16
16
16
8
16
112
1
1
4
TOOL REQUIRED
PHILLIPS SCREWDRIVER HAMMER

A
B
C
D
E
F
NOTE: FIRST MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED ON THIS SHEET. IF YOU ARE MISSING ANY PIECE(S), DO NOT
ASSEMBLE THE UNIT. INSTEAD, CALL OUR CUSTOMER SERVICE NUMBER AT: [phone]. WE WILL BE HAPPY TO ASSIST YOU.
2380A-Top
2380B-Bottom
2380C-Base
PARTS ARE USUALLY MARKED ON THE RAW EDGE
1pc
1pc
1pc
2380D-Divider
2380E-Face Panel
2380F-Adjustable Shelf
4pcs
4pcs
28pcs

1
E
CAMLT12
UNLOCKED
POSITION
SPE610BL
BM25
Do not tighten screw on the amgle bracket all the way in
this step. Leave it a bit loose until you attach part D in
the next step. Then you will tighten the screws.
Use small hole #4
from the left end.
Use small hole #4
from the right end.

2
D
E
D
E
SPE610BL
Repeat steps 1 and 2 for the remaining three sets of part (D) & (E)
P
ress par
t
(D)
i
n
th
e groove o
f
par
t
(E)
.
Th
e
h
o
l
es
i
n par
t
(D)
s
h
ou
ld
face away from part (E), except for holes where brackets are attched,
and RED marked end of it should be on the same side as on part (E).
Make sure part (E) and (D) are aligned with each other on both ends.
If you experience difficulty in lining up boards E and D
with the angle brackets, try the following:
1) loosen the screw on the angle bracket attached to
board E,
2) line up angle bracket hole with board D and attach
screw into bracket and hole on board D,
3) tighten screws on boards D and E until both boards
are pulled together and fit properly.

3
B
CAMBT16
A
B
C
TRNTSC
TRNTPL
DOWW830
Finished Side

4
1
2
34
Turn camlocks clockwise
using flat (preferred) or
phillips scrdriver until full
stop(slightly over12a turn
to lock the bolt)
Lock camlocks on panels E as
you install them before you
proceed to next one.
Otherwise panels may fall over
and cause damage. Make sure
you have on top only RED
marked ends of panels D & E

5
A
Turn camlocks
clockwise until
full stop (slightly over12
a turn to lock the bolt)
BPBL54
CCPZXX
If you'd like to optimize the space for CD or
DVD/VHS only, then use these holes (counting
from the top):
CD: 1 3 5 6 8 10 11. Total 8 spaces for storage
DVD/VHS: 2 4 7 9 11. Total 5 spaces for storage
Install
top
first
.
Next
install
one
shelf
in
the
middle
(#6
or
#7
,
depending
if
you
re
going to use it for CD or DVD.) on each side to restrict movement of inside
dividers D. Do not tap with hammer onto shelf supports, instead twist them when
inserting in.