venture horizon 3117 User manual

IF PARTS ARE MISSING AND OR DEFECTIVE, INSTRUCTIONS ARE NOT CLEAR
OR YOU ARE EXPERIENCING PROBLEMS ASSEMBLING OUR PRODUCT.
BEFORE YOU RETURN THE PRODUCT TO THE STORE,
PLEASE CALL US TOLL FREE FOR CUSTOMER SERVICE ASSISTANCE
[phone]
OR SEND US EMAIL AT
[email protected]
PLEASE HAVE ITEM NUMBER READY, AND A REPRESENTATIVE WILL GLADLY ASSIST YOU
SPARTAK ENTERPRISES, INC.
CHEST OF DRAWERS
Model #3117-21BL
LOT #2397
SPARTAK ENTERPRISES, INC. 841 E. FRANCIS STR. ONTARIO, CA. 91761 TEL; 909/930-0670 FAX; 909/930-9921

J
I
E
B
A
3027G-Drawer Right Side 8pcs
3027H-Drawer Front 8pcs
3027I- Drawer Bottom 8pcs
3117J-Back Panel 2pcs
3117K-Bottom 1pc
3117L-Divider 1pc
3117M-Center Support 1pc
3117A-Side Panel Left 1pc
3117B-Side Panel Right 1pc
3027D-Drawer Back 8pcs
3117E-Top 1pcs
3027F-Drawer Left Side 8pcs
NOTE: FIRST MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED ON THIS SHEET. IF YOU ARE
MISSING ANY PIECE(S), DO NOT ASSEMBLE THE UNIT. INSTEAD, CALL CUSTOMER SERVICE NUMBER
AT: [phone]. WE WILL BE HAPPY TO ASSIST YOU.
PARTS IDENTIFICATION
K
L
M
D
H

CAMLT12
CAMBT16
DOWW830
GLIDE22MM
PUSH
SRM815B
GLUEWD
NAIL1734
SCF507HB
SFH845A
ALLEN4
BM25
SPE610BL
SC--S
SP811BL
SFH833A
HARDWARE PART NUMBER DESCRIPTION QTY
HARDWARE LIST
7
7
8
5
8
16
2
24
2
6
1
32
64
4
12
32
CAMLOCK
BOLT
WOOD DOWEL
GLIDE
SHELL METAL PULL
MACHINE SCREW
GLUE
NAIL
CONFIRMAT SCREW
WOOD SCREW
HEX KEY
ANGLE BRACKET
EURO SCREW
SCREW COVER CAP
PAN HEAD SCREW
WOOD SCREW

1
When first inserting camlocks, make sure they
always point towards edge of board as indicated.
UNLOCKED
POSITION
K
L
SCF507HB

2
DOWW830
Insert wood dowels by tapping onto
them with a hammer. Make sure
they go in as far as possible. Wood
dowels should not stick out more
than 1/2"
When first inserting camlocks, make sure they
always point towards edge of board as indicated.
CAMBT16
E
A&B

When locked, arrow on camlock should point away from the edge as indicated.
3
Turn camlock
clockwise to
lock the bolt
SFH845A
A
K
L
B

4
Handle the assembly with care to avoid damage of bottom part (K).
K
A
L
B

5
E
Turn camlock
clockwise to
lock the bolt
Press down onto the Top to make
sure wood dowels go in all the way
and that there is no gap left between
Sides and the Top.

6
NAIL1734
GLIDE22MM
Place the unit face down. Align the Back Panel (J) over the of the unit. Make sure the assembly is
square and leave equal amount of margin all around. Secure the panel by screwing 6 screws through
the pre-drilled holes for both panels (2 screws on both ends and 2 screws in the center). Next, nail the
top and bottom (as shown above) with approximately 4" spacing between the nails. Make sure to
keep the nails centered on the edges to avoid splitting of the boards.
J
J
SP811BL

7
G
F
G
F
H
SPE610BL
BM25
I
SPE610BL
Note: Once parts (F and G)
have been attached to part (H)
with the euro screws, a total of
four each. Then slide in the
bottom part of the drawer
(Part I).
F
G
I
H

8D
Place (D) onto (in between)
Drawer Sides (F) and (G). Repeat
last steps for the rest of the
drawers.
D
I
D
I
FF
D
Note: Attach the handle with
two screws as shown to the
right.
Note: Attach part (D) with
two screws on both sides
(Parts F & G) a total of four
screws as shown below.
SFH833A
SRM815B

9
Note: Insert the drawers by following the
diagram below. Start from the bottom and
work your way up. This way you can have a
clear view where to insert the next drawer.
1
2
3
4