venture horizon 2412 User manual

SPARTAK ENTERPRISES, INC.
MEDIA STORAGE RACK DOUBLE
Model #2412-21BL
LOT #2496
IF PARTS ARE MISSING AND OR DEFECTIVE, IF INSTRUCTIONS ARE NOT CLEAR
OR IF YOU ARE EXPERIENCING PROBLEMS ASSEMBLING OUR PRODUCT.
BEFORE YOU RETURN THE PRODUCT TO THE STORE,
PLEASE CALL US TOLL FREE FOR CUSTOMER SERVICE ASSISTANCE
[phone]
OR SEND US EMAIL AT
[email protected]
PLEASE HAVE ITEM NUMBER READY, AND A REPRESENTATIVE WILL GLADLY ASSIST YOU
SPARTAK ENTERPRISES, INC. 841 E. FRANCIS STR. ONTARIO, CA. 91761 TEL; 909/930-0670 FAX; 909/930-9921

NOTE: FIRST MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED ON THIS SHEET. IF YOU ARE MISSING ANY PIECE(S), DO NOT
ASSEMBLE THE UNIT. INSTEAD, CALL OUR CUSTOMER SERVICE NUMBER AT: [phone]. WE WILL BE HAPPY TO ASSIST YOU.
A
B
C
D
E
FL-FR
GK
PARTS ARE USUALLY MARKED ON THE RAW EDGE.
2402A-Top
2402B-Base
2411C-Molding
2411D-Back Support
2411E-Outer Side
1pc
1pc
3pcs
2pcs
2pcs
2411FL-Back Panel Left
2411FR-Back Panel Right
2402G-Stretcher
2411K-Shelf
2401 -Brace
2412J-Inner Divider
2pcs
2pcs
2pcs
24pcs
2pcs
1pc
J

SFH845A
BM25
SPE610BL
BPXX54
DOWW525
CAMLT12
CAMBT16
SPB1016BL
CCPZXX
SHPL5
WOOD SCREW
BRACKET ANGLE
EURO SCREW
SHELF SUPPORT
WOOD DOWEL
CAMLOCK
BOLT
PAN HEAD SCREW
CAMLOCK COVER CAP
SHELF LOCK
HARDWARE PART # DESCRIPTION QTY
12
4
8
144
41
16
16
24
12
48
TOOL REQUIRED
PHILLIPS SCREWDRIVER HAMMER

1
Unlocked
Position
DOWW525 D
CAMBT16
E & J
A
B

2
BE
D
J
D
E
Make sure groove on parts E and J should
be located at the bottom edge. If it's not-
then you had installed it upside down.
B
Turn camlocks clockwise
using flat (preferred) or
phillips screwdriver until
full stop(slightly over 12a
turn to lock the bolt)

3
A
DOWW525
Do not use more than one drop of glue as it may cause board to split.
Make sure the dowels go in as far possible. They should stick out no more than 3/8 of an inch.
Turn camlocks clockwise
using flat (preferred) or
phillips screwdriver until
full stop(slightly over 12a
turn to lock the bolt)

4
C
C
C

5
SPE610BL
SPE610BL
Attach part onto
top A

SFH845A
6
G
G
SPB1016BL
Use small screws on the
back panel between Outer
Sides(E) and dividers (J).
Use long screws only
on the Outer Sides(E)
and dividers (J).

SPB1016BL
7
MARKED
BLUE MARKED
RED MARKED
BLUE MARKED
RED
Install Back Panels as shown, with unmarked edges facing down and
blue or red marked being atop. Make sure the Blue is on the left side
and Red is on the right side of each section. Otherwise you will have
problem with leveling of the shelves, they will sag in the middle.

8
G
G
.
If you live in an earthquake zone,
we recommend using
the anti-toppling device provided to increase the safety in your home.
Please follow the diagrams below. We provide two pilot holes in the
back of the Top to attach a straps which you can secure to the wall.
You can also, at your option secure unit through by screwing the back
support (D) to the wall.
WALL
STRAP

9
SHPL5
K
Do not tap with hammer onto shelf supports, instead twist them when inserting in.
You will be using six shelf supports per shelf, two on each side and two in the back.
Install shelves at desired locations.Use a case
of CD or DVD as a template to locate postions
for the shelves. Start from the bottom. If you
skip a hole or mix in one section with CD or
DVD/VHS cases, you may end up with some
unused space at the top. In other words, to get
the maximum capacity, don't skip any holes or
mix different kinds of media in one section.
CCPZXX
To prevent shelves from sagging,
lock the back corners of them from
above with two round Shelf Locks.
BPBL5