venture horizon 2385 User manual

SPARTAK ENTERPRISES, INC.
SWIVEL MEDIA TOWER
Model #2385-21BL
LOT# 2661
IF PARTS ARE MISSING AND OR DEFECTIVE, IF INSTRUCTIONS ARE NOT CLEAR
OR IF YOU ARE EXPERIENCING PROBLEMS ASSEMBLING OUR PRODUCT.
BEFORE YOU RETURN THE PRODUCT TO THE STORE,
PLEASE CALL US TOLL FREE FOR CUSTOMER SERVICE ASSISTANCE
[phone]
OR SEND US EMAIL AT
[email protected]
PLEASE HAVE ITEM NUMBER READY, AND A REPRESENTATIVE WILL GLADLY ASSIST YOU
SPARTAK ENTERPRISES, INC. 841 E. FRANCIS STR. ONTARIO, CA. 91761 TEL; 951/360-0610 FAX; 951/360-0775

CCPZXX
CAMLT12
CAMBT12
BM25
SPE610BL
BPXX54
TRNTPL
TRNTSC
DOWW830
CAMLOCK COVER CAP
CAMLOCK
BOLT
BRACKET ANGLE
EURO SCREW
SHELF SUPPORT
SWIVEL PLATE
SWIVEL BOLT
WOOD DOWEL
HARDWARE PART # DESCRIPTION QTY
16
16
16
8
16
128
1
1
4
TOOL REQUIRED
PHILLIPS SCREWDRIVER HAMMER

ABC
D
E
F
NOTE: FIRST MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED ON THIS SHEET. IF YOU ARE MISSING ANY PIECE(S), DO NOT
ASSEMBLE THE UNIT. INSTEAD, CALL OUR CUSTOMER SERVICE NUMBER AT: [phone]. WE WILL BE HAPPY TO ASSIST YOU.
2385A-Top
2385B-Bottom
2385C-Base
PARTS ARE USUALLY MARKED ON THE RAW EDGE
1pc
1pc
1pc
2382D-Divider
2385E-Face Panel
2382F-Adjustable Shelf
4pcs
4pcs
32pcs

1
E
CAMLT12
UNLOCKED
POSITION
SPE610BL
BM25
Do not tighten screw on the angle bracket all the way in
this step. Leave it a bit loose until you attach part D in
the next step. Then you will tighten the screws.
Use small hole #4
from the left end.
Use small hole #4
from the right end.

2
D
E
D
E
Repeat steps 1 and 2 for the remaining three sets of part (D) & (E)
SPE610BL
Press part (D) in the groove of part (E). The holes in part (D) should
face away from part (E), except for holes where brackets are attched,
and RED marked end of it should be on the same side as on part (E).
Make sure part (E) and (D) are aligned with each other on both ends.

3
B
CAMBT12
A
B
C
TRNTSC
TRNTPL
DOWW830
Top Side

4
12
3
4
Turn camlocks clockwise
using flat (preferred) or
phillips scrudriver until full
stop(slightly over12a turn
to lock the bolt)
Lock camlocks on panels E as
you install them before you
proceed to next one.
Otherwise panels may fall over
and cause damage. Make sure
you have on top only RED
marked ends of panels D & E

5
A
Turn camlocks
clockwise until
full stop (slightly over12
a turn to lock the bolt)
BPBL54
CCPZXX
First
attach
the
top
(A)
and
lock
it
in
place
.
Next
install
one
shelf
in
the
middle
using
either hole#6 or 7, depending if you re going to use it for CDs or DVDs (see
instruction at the botom of this page) on each side to restrict movement of inside
dividers D. Do not tap with hammer onto shelf supports, instead twist them when
inserting in.
If you'd like to optimize the space for CD or DVD/VHS
only, then use these holes (counting from the top):
CD: 1 2 3 5 7 8 10 12. Total 9spaces for storage
DVD/VHS: 2 4 6 9 11. Total 6 spaces for storage