Verizon 5G Home Router User manual

5G Home Router
User Guide

i
Federal Communication Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25 GHz band are restricted to indoor usage only.

ii
RF Exposure Statement
To comply with FCC RF exposure compliance requirements, the antenna used
for this transmitter must be installed to provide a separation distance of at least
31cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
Safety Warnings
Adapter
Do not use any other power adaptor except the one that accompanies this unit
or a power adaptor identified in the list below.
Use of another adapter could result in damage to the unit.
The following power adaptor is qualified for use with this Verizon 5G Home
Router:
This unit must be powered by LUCENT TRANS, model 1A95 or equivalent UL
listed power source rated @ output 19Vdc, Maximum 2.37A.

iii
Table of Contents
Chapter 1 Introduction..................................................................................................................................... 1
1.1 Unboxing Information......................................................................................................................... 1
1.2 Key Features........................................................................................................................................ 1
1.3 Top Panel (LEDs) ................................................................................................................................ 1
1.4 Back Panel............................................................................................................................................ 4
Chapter 2 Connecting the 5G Home Router ............................................................................................. 5
2.1 Setting up the 5G Home Router ...................................................................................................... 5
2.2 Configuring the 5G Home Router ................................................................................................... 5
2.3 Connecting Other Devices ............................................................................................................... 6
2.4 Pairing your mobile device and turning the 5G Home Router into a Bluetooth speaker..... 7
Chapter 3 Accessing the Web User Interface .......................................................................................... 8
3.1 Login ………………………………………………………………………………………………………………………………………………. 8
3.2 Home Page/Main Section ................................................................................................................. 9
3.3 Wi-Fi Settings .................................................................................................................................... 12
3.4 Connected Devices .......................................................................................................................... 17
3.5 Firewall................................................................................................................................................ 21
3.6 Parental Controls.............................................................................................................................. 24
3.7 System Settings ................................................................................................................................ 26
3.8 Diagnostic........................................................................................................................................... 31
Chapter 4 Product Specifications.............................................................................................................. 32

1
Chapter 1
Introduction
This chapter includes a list of items included with the 5G Home Router (LVR1), an overview of the
5G Home Router’s features, and a description of the user interface and ports on the 5G Home
Router.
1.1 Unboxing Information
Inside the product package for the 5G Home Router (LVR1), you should find the following items:
• 5G Home Router
• AC adaptor
• Ethernet cable
1.2 Key Features
• Tri-Band Wi-Fi 802.11AX capable 5G Home Router to maximize throughput and coverage.
• 2.5GbE (WAN & LAN) port and two 1GbE ports.
• Built-in mic and speaker for Alexa Voice Service
• Bluetooth for music playback
1.3 Top Panel (LEDs)
1. Touchpad (Activated when AVS is provisioned)
A circular touchpad is located on the top panel of the 5G
Home Router (LVR1). This is the main interface for setting up
the 5G Home Router.
Note: Please remove the clear protective film from the top
before use.
2. Action Button
A touch-sensitive action button is located in the center of the
touchpad on top of the 5G Home Router. You can use this
button to turn off alerts, wake up Alexa, interrupt an Alexa response, or reset the Alexa Voice
Service (AVS). To reset AVS, press and hold down the button for 5 seconds.

2
3. Volume Adjustment Buttons
Touch-sensitive volume adjustment buttons are located on the left and right sides of the
touchpad on top of the 5G Home Router. The “+” button raises volume, while the “-” button
lowers volume.
4. Mute Button
A touch-sensitive mute button is located near the upper edge of the touchpad above the action
button.
5. Microphones
Four microphones are located on the touchpad, arranged in a square pattern to determine the
direction of the user’s voice.
6. Circular LED Light
A recessed circular LED light surrounds the touchpad on top of the 5G Home Router. The LED
will light up in different ways to indicate the connectivity status of the 5G Home Router.
LED Notification Guide
Function Status LED Ring
Pairing (WPS /
Bluetooth®)
Not paired to Receiver (CPE)
Animation
Red/Amber
Pairing mode active
If WPS fails, use an Ethernet cable to pair the 5G
Home Router and extender
Animation
Blue
Pairing success
Animation
Blue
Pairing fail
Animation
Red
Wi-Fi and
Internet
5G Home Router connected to CPE and
Internet is active, but Wi-Fi is turned Off.
Solid
Amber
Wi-Fi quality between IDU and 5G Home
Router is poor.
Animation
Yellow and white ring

3
5G Home Router connected to CPE, but no
Internet connection (5G node might be
down)
Animation
Red/Amber
5G Home Router connected to CPE, Wi-Fi
and Internet working well.
Solid
White (turns off after 30 seconds)
Usual Functions
Firmware upgrade
Fast Blink
White
Hard reset / Reboot
Fast Blink
White
Turn ON device
Animation
White to Red/Blue
Alexa Voice
Service
Microphones on your device are turned off.
Press the Microphone button to turn on the
microphones.
Solid
Red
A message or notification is waiting for you.
Say, "Play my messages" or "What are my
notifications?"
Pulsing
Yellow
Adjusting the volume level on your device.
White
Do Not Disturb is enabled for Alexa.
Single flash
Purple

4
1.4 Back Panel
1. WAN Port
The WAN Port (the red Ethernet port) connects the 5G Home Router to a 5G CPE using an
Ethernet cable.
2. LAN Ports
Three LAN ports (one 2.5 Gbps port on the rightmost
and two 1 Gbps ports in the middle) enable you to
connect devices to the 5G Home Router via Ethernet
cables.
3. Reset Pinhole
To reset the 5G Home Router to factory defaults, insert
a pin into the pinhole, press down, and hold for 5
seconds.
4. Power Jack
Connect the AC adaptor (power source rated @ output 19Vdc, maximum 2.37A) to the Power
Jack to provide power to the 5G Home Router from an electrical outlet.
5. Multi-purpose Pairing Button
Press this button once to connect the Router to other devices via WPS or Bluetooth®. After the
pairing is successful, the circular LED light will illuminate blue for two seconds.

5
Chapter 2
Connecting the 5G Home Router
This section describes how to set up and configure your 5G Home Router.
2.1 Setting up the 5G Home Router
1. Unbox the 5G Home Router, AC adaptor, and Ethernet cable.
2. Plug the AC adaptor into an electrical outlet, then connect the other end to the power jack on
the back of the 5G Home Router.
3. Plug an Ethernet cable into the WAN port on the back of the 5G Home Router, and plug the
other end of the Ethernet cable into an Ethernet port on your CPE.
Optional
If an Ethernet cable is not used, you can connect to the CPE using WPS:
Press the WPS button on the CPE and that of your 5G Home Router. Make sure the CPE is
within range of the 5G Home Router. The circular LED light will illuminate blue for two
seconds to indicate pairing success. You may also use the WPS button in the Web User
Interface to activate WPS by clicking Wi-Fi Settings > WPS, and click on the Primary Wi-Fi
WPS button.
Note: It’s recommended that you move the device to be paired into close proximity of the 5G
Home Router (preferably less than a meter away), making it easier to press pairing buttons
within the allotted 2 minutes in the WPS procedure. After pairing is successful, you can then
move the 5G Home Router to the location of your choice and check the LED for Wi-Fi signal
strength at the chosen location.
2.2 Configuring the 5G Home Router
Connect a computer to the 5G Home Router and open a web browser. Type http://my.router in
the address bar, and press Enter (on the computer’s keyboard). A login screen will then appear.

6
Type in your password, which is printed on the product label, to enter a configuration screen.
2.3 Connecting Other Devices
The 5G Home Router can connect to other devices via Ethernet and via wireless connection.
Ethernet
1. Take an Ethernet cable and plug one end into one of the LAN ports on the back of the 5G
Home Router.
2. Plug the other end of the Ethernet cable into an Ethernet port on one of the other
devices.
3. Repeat these steps to connect more devices to the 5G Home Router via Ethernet.
Wireless
1. Ensure that the devices you wish to connect wirelessly to the 5G Home Router have Wi-
Fi capability.
2. Make sure the devices are using the same SSID and password as the 5G Home Router
by launching each of the devices’ wireless applications.