Verkada CB61 User manual

CB51
|
CB61 Outdoor Bullet Camera

What you’ll need
• A working internet connection
• A smartphone or laptop
• A Cat5 or Cat6 ethernet cable with a
.2-.25 inch outside diameter (5-6.5mm)
• 802.3af/802.3at POE Power over Ethernet
(PoE) switch, or a PoE injector. For
operation below -20° C, use 802.3at PoE
• A #2 Phillips screwdriver or power drill with
a #2 Phillips driver bit
• ⁄ inch (3mm) drill bit for pilot holes

5
In the box
1 CB51 / CB61 outdoor bullet camera
1 Mount plate (pre-assembled with camera)
1 Setup guide, with 1 mounting template
1 T8, T25 Hand tool
1 22mm cable gland wrench
4 Wall mounting screws
4 Adapter mounting screws
1 Junction box adapter cover
1 Junction box adapter mount plate
1 Spare collar locking screw
CB51 / CB61 Outdoor Bullet Camera
Mount Plate
(pre-assembled with camera)
Mounting
Hardware
T8 and T25
Hand Tool
Cable Gland Wrench
Junction Box
Adapter Cover
Junction Box Adapter
Mount Plate
Setup Guide with
Mounting Template
1/8” (3mm) holes for
wood or metal
1/4” (6mm) holes for
plastic anchors
Drill 4 holes:
Drill cable
pass through
(optional)
Rear cable exit
route (optional)
CB51 Mount Plate
(front side)
CB51 / CB61
Mount Plate
Template
Bullet Camera

7
Mount Plate
Removable Cover
Collar Locking Screw
Ball Joint
Lock Screw
Optional Cable Exit
Cover Collar
Base Plate Base Locking
Screw
Status LED
CB51
|
CB61 Overview
3/4” NPT Threaded
Connection

9
CB51
|
CB61 Connect
Use the T8 drive to loosen the set screw. Do not completely remove the screw.
Twist the Cover Collar near the middle of the camera to remove the outer Cover.

10 - connect connect - 11
Solid orange
Camera is on and booting up
Flashing orange
Camera is updating firmware
Flashing blue
Camera is recording, but
cannot reach the server
Solid blue
Camera is running, connected,
and streaming video
Status LED
Connect CB51 / CB61 to an
802.3af/802.3at Power over Ethernet
(PoE) port on your network
Go to www.verkada.com/start
For detailed installation instructions,
visit www.verkada.com/support
Insert the ethernet cable into ethernet port. Scan the QR code for easy
camera registration and setup, or proceed to www.verkada.com/start.

13
CB51
|
CB61 Mounting
To unlock the Mount Plate from the Base Plate, loosen the Base Locking Screw
using the provided T8 hand tool. The screw should be backed out approximately
.2” (5mm) from the Base Plate. Do not fully remove the screw.

14 - mount mount - 15
Use the provided mounting template to mark Mount Plate holes.
For a solid material like wood or metal, drill 1/8 inch pilot holes. Drive mounting
screws directly into the pilot holes.
For drywall, plaster or masonry, separate wall anchors may be required.
To remove the Mount Plate from the Base Plate, twist the Mount Plate counter-
clockwise then pull the Mount Plate o of the underside of the Base Plate.
1
2

16 - mount mount - 17
Feed ethernet cable through the center of the Mount Plate
before fully securing it to the mounting surface.
Leave enough slack to safely handle the camera during cable
gland installation.
Remove the cable gland from CB51 / CB61.
Route the ethernet cable through the Mount Plate and ball
joint. Leave the cable disconnected for now.

18 - mount mount - 19
1
2
Engage the mounting pegs and twist clockwise until you feel the camera lock
securely in place.
Once secured, tighten the T8 security screw using the provided hand tool.
Align mounting features on the Mount Plate with the
mounting pegs on the backside of CB51 / CB61 Base Plate.

20 - mount mount - 21
Slide the cable gland assembly into pass through, seating it in position. Gently tighten down the metal nut by hand. You should still be
able to move the cable back and forth through the gland.
Slide the metal nut over the RJ45 connector and engage the
threads on the pass-through.
Firmly push the rubber seal and plastic collar together.

22 - mount mount - 23
Push the excess ethernet cable back through the cable gland assembly. Plug in
the ethernet cable to the camera’s RJ45 jack. The cable should be routed straight
from the cable gland into the RJ45 jack.
Firmly tighten the metal nut using the included wrench.

25
CB51
|
CB61 Secure
To finish securing the device, align the outer Cover with the camera and push into place.
The external threads on the outer Cover will meet the internal threads on the Cover
Collar at the back of the housing.

26 - secure secure - 27
Rotate the Cover Collar to thread the outer housing into place. The outer Cover will
be pulled into place and should seat against the ring when fully tightened.
Use the T8 security key to tighten the set screw on the side of the Cover Collar
to increase tamper resistance.

29
CB51
|
CB61 Adjust
Adjust your camera to the desired viewing angle. Use the online stream to
confirm image orientation. Image can be flipped 180˚ online in Command.

30 - adjust adjust - 31
To lock the camera in place, use the T25 security torx key to turn the
screw on the side of stand. This will tighten the ball joint.
To fully secure the device, rotate the torx handle 90 degrees and
tighten the screw further.
Pan
Tilt
Rotate

[phone]
[email protected]
www.verkada.com/support