Verkada D40 User manual

D40 Setup Guide

Contents
In the box 1
What you’ll need 3
Connect 5
Mount 7
Secure 17
Support 19

1 2
In the box
D40 Camera

1 2
Mount plate
3 screws 3 wall anchors
2 machine screws 2 wing nuts2 washers
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
b
l
e
C
a
b
l
e

3 4
What you’ll need

3 4
• A working internet connection
• 802.3af Power over Ethernet (PoE) switch,
or a PoE injector
• A smartphone or laptop
• A Phillips screwdriver or power drill with a Phillips driver bit
• 1/4-inch (6.5mm) drill bit for wall anchors
• 1/8-inch (3mm) drill bit for pilot holes
• 3/16-inch (4.5mm) drill bit for machine screws

5 6
Connect
Grasp the plastic mount plate strap and pull
the cover o of the camera.

5 6
Connect the camera to an 802.3af Power
over Ethernet port on your network. An
orange LED on the camera’s ethernet port
will indicate that it is powered and booting
up. A green LED on the ethernet port will
indicate the camera is active.
Go to www.verkada.com/start

7 8
Mount

7 8
Firmly pull and seperate the mount plate
from the camera base. Remove and
discard the plastic mount plate strap.
On the bottom of the camera, rotate the
mount plate clock-wise until it stops and
is lined up with its corresponding blue
colored notch on the camera base.

9 10
Mount
continued

9 10
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
b
l
e
C
a
b
l
e
When placing the mount plate, take care to
orient it such that your camera’s target is
situated within the “Camera Pan Angle”.
If your cable is routed through a hole in
the mounting surface, position one of the
mount plate’s notches labeled “Cable” as
close to the cable hole as possible.
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a

11 12
Mount
continued

11 12
For a solid material like wood or metal, drill
1/8-inch pilot holes. Drive mounting screws
directly into the pilot holes.
1/8 inch
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
Use the mount plate to mark holes for
mounting screws.

13 14
Mount
continued

13 14
For drywall, drill 1/4-inch holes. Insert
plastic anchors into holes and drive
mounting screws into anchors.
For a drop ceiling, drill 3/16-inch holes
through the ceiling tile and insert machine
screws. Behind the ceiling tile, place
washers and wing nuts on each screw and
hand tighten.
1/4 inch
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
3/16 inch
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a

15 16
Mount
continued

15 16
Plug in the camera. Line up the blue
notches on the mount plate and the
camera body and place the camera over
the center pin on the mount plate.
With the camera on the mount plate, rotate
the entire camera body on the mount plate
to adjust the pan angle. Tilt and rotate just
the camera lens for further adjustment.
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a

17 18
Secure