Verkada CM41 User manual

CM41 Setup Guide

Contents
In the box 1
What you’ll need 3
Connect 5
Mount 7
Secure 13
Support 15

1 2
In the box
CM41 Camera
Mount plate
3 screws
Length (including head) 52.5 mm,
Width 4 mm, Head width 8.3 mm
3 wall anchors
2 machine screws
Length (including head) 27.6 mm,
Width 4 mm, Head width 7 mm
2 wing nuts2 washers
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
b
l
e
C
a
b
l
e

3 4
• A working internet connection
• 802.3af Power over Ethernet (PoE) switch,
or a PoE injector
• A smartphone or laptop
• A Phillips screwdriver or power drill with a Phillips driver bit
• 1/4-inch (6.5mm) drill bit for wall anchors
• 1/8-inch (3mm) drill bit for pilot holes
• 3/16-inch (4.5mm) drill bit for machine screws
What you’ll need

5 6
Connect
Grasp the plastic mount plate strap and pull
the cover o of the camera.
Connect the camera to an 802.3af Power
over Ethernet port on your network. An
orange LED on the camera’s ethernet port
will indicate that it is powered and booting
up. A green LED on the ethernet port will
indicate the camera is active.
Go to www.verkada.com/start
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a

7 8
Mount
Firmly pull and seperate the mount plate
from the camera base. Remove and
discard the plastic mount plate strap.
On the bottom of the camera, rotate the
mount plate clock-wise until it stops and
is lined up with its corresponding blue
colored notch on the camera base.

9 - Mount Mount - 109 10
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
b
l
e
C
a
b
l
e
When placing the mount plate, take care to
orient it such that your camera’s target is
situated within the “Camera Pan Angle”.
If your cable is routed through a hole in
the mounting surface, position one of the
mount plate’s notches labeled “Cable” as
close to the cable hole as possible.
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
For a solid material like wood or metal, drill
1/8-inch pilot holes. Drive mounting screws
directly into the pilot holes.
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
1/8 inch
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
Use the mount plate to mark holes for
mounting screws.

11 - Mount Mount - 1211 12
For drywall, drill 1/4-inch holes. Insert
plastic anchors into holes and drive
mounting screws into anchors.
For a drop ceiling, drill 3/16-inch holes
through the ceiling tile and insert ma-
chine screws. Behind the ceiling tile,
place washers and wing nuts on each
screw and hand tighten.
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
1/4 inch
C
a
b
l
e
C
a
b
l
e
C
a
m
e
r
a
P
a
n
A
r
e
a
C
a
m
e
r
a
P
a
n
A
r
e
a
3/16 inch
Plug in the camera. Line up the blue
notches on the mount plate and the
camera body and place the camera over
the center pin on the mount plate.
With the camera on the mount plate, rotate
the entire camera body on the mount plate
to adjust the pan angle. Tilt and rotate just
the camera lens for further adjustment.

13 14
Route the cable snuggly between the
camera base and the mount plate. Place
the cover on the camera. Be sure the
magnets have pulled the cover flush
against the mounting surface.
Secure
Solid orange
Camera is on and booting up
Flashing orange
Camera is updating firmware
Flashing blue
Camera is recording, but
cannot reach the server
Solid blue
Camera is running, connected,
and streaming video
Status LED

15
Thank you for purchasing a Verkada
camera.
If for any reason things don’t work right or
you need assistance, please contact us
immediately.
Sincerely -
The Verkada Team
Support

17 PB
www.verkada.com/support