Verkada BC82 User manual
Document
Document Details
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
V1.0 (20230127)
(V1.0 first published 20230127)
Firmware
Firmware version can be verified on
Verkada Command command.verkada.com.
Product Model
This install guide pertains to model BC82-HW.
2
Introduction
What’s in the box
What you’ll need
●A working internet connection
●A smartphone or laptop
●A #2 Phillips screwdriver or
power drill with a #2 Phillips driver bit
●1/4 inch (6.5mm) drill bit for wall anchors
●1/8 inch (3mm) drill bit for pilot holes
●A shielded Cat5 or Cat6 Ethernet cable
with a .2‘’-.25” outside diameter (5-6.5mm)
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
BC82 Alarm Panel
3
Mount Plate
(Attached to alarm panel)
4 M4 x 25mm PH2 Wall
Screws, and Wall Anchors
Connect
For easy registration and setup, scan
the QR code on the back of the
product.
If you prefer to manually register your
product, please proceed to:
verkada.com/start
T10 Security Torx Screwdriver
Introduction
Overview
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
LED
4
Speaker & Buzzer
10.1” Touchscreen
Camera
LED Behavior
Solid Orange
Hub is on and booting up.
Flashing Orange
Hub is updating firmware.
Flashing Blue
Hub can receive events but cannot
reach the server.
Solid Blue
Hub is running, connected, and
receiving events.
Introduction
Mount Template
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
5
Mount plate details
Use the mount plate as a template and mark
the correct hole pattern.
A Wall mount
B Single gang junction box
European junction box
3.5’’ Round junction box
C 4’’ Round junction box
Mount plate details
Use the mount plate as a template
and mark the correct hole pattern.
A Wall mount
B Square Junction Box (4”)
C Single Gang Junction Box
D Round Junction Box (4” & 3-½”)
E Double Gang Junction Box
F European Junction Box
G VESA Mount (100x100 mm)
H Verkada ACC-CON-STD-1
Installation
Remove mount plate
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
7
Use the provided T10 Torx security torx
screwdriver to loosen the security screw.
Slide downward to unhook the mount plate.
Make a darker
color/lighter color to
not blend in so much
Installation
Mounting Template
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
8
Use the mounting template to help align
mounting plate to the wall. Mark the four
corners (A) on the wall.
Use provided screws and wall anchors to
mount plate onto the wall.
1. Use mount plate, drill hole [ view
of wall and setting mount plate
and highlight the four holes]
2. Hole drilled and mount plate and
four screws in that direction
1. Highlight all the holes w blue [in
the center]
Recommend to screw into the hole
pattern A if possible (4 corners holes
marked above) for the most secure
mounting.
A
A
A
A
Installation
Connect
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
10
Scan QR Code info
For easy registration and setup,
scan the QR code on the
product.
If you prefer to manually
register your product, please
proceed to:
verkada.com/start
Installation
Mounting option 1
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
11
Cable exit through mounting surface
1 - Connect the Ethernet cable to RJ45 connector.
2 - With the cable connected to BC82 and exit
through the mounting surface. Place BC82 back onto
the mounting plate and engage with all 3 hooks to
secure.
3 - To secure BC82, tighten the security screw using
the provided T10 Torx security torx screwdriver.
For easy registration and setup,
scan the QR code on the
product.
If you prefer to manually
register your product, please
proceed to:
verkada.com/start
Break up the steps to be
nex tto images
Use a callout bubble to
tighten screw
Installation
Mounting option 2
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
12
Cable exit along the mounting surface
1 - Connect the Ethernet cable to RJ45 connector.
2 - With the cable connected to BC82 and exit
downward along the mounting surface. Place BC82
back onto the mounting plate and engage with all
3 hooks to secure.
3 - To secure BC82, tighten the security screw using
the provided T10 Torx security torx screwdriver.
For easy registration and setup,
scan the QR code on the
product.
If you prefer to manually
register your product, please
proceed to:
verkada.com/start
Bottom view like
the view on the
left
Flip steps; ref BR31
slide 8; check how to
mount thor
Appendix
Compliance
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
13
FCC
Statement
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement :
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Any changes or modifications not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
Appendix
Compliance
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
14
IC
Statement
Innovation, Science and Economic Development Canada(ISED)Compliance Statement
This device complies with ISED’s licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the
device.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
Caution:
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems;
This equipment supports DFS (Dynamic Frequency Selection) to minimize interference and/or damage caused
by the high-power radars that are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz
and 5470-5725 MHz.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
NOTE IMPORTANTE:
Déclaration d'exposition aux rayonnements d'IC :
Cet équipement est conforme aux limites d'exposition aux rayonnements IC RSS-102 définies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm
entre le radiateur et votre corps.
Avertissement:
Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l’intérieur
afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes
canaux;
Cet équipement prend en charge DFS (Dynamic Frequency Selection) pour minimiser les interférences et/ou
les dommages causés par les radars haute puissance qui sont attribués en tant qu'utilisateurs principaux
(c'est-à-dire les utilisateurs prioritaires) des bandes 5250-5350 MHz et 5470-5725 MHz.
Appendix
Support
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
Thank you for purchasing this Verkada product. If for any reason
things don’t work right, or you need assistance, please contact us
immediately.
verkada.com/support
Sincerely, The Verkada Team
15
Other manuals for BC82
1
This manual suits for next models
1
Table of contents
Other Verkada Security System manuals
Popular Security System manuals by other brands
Altronix
Altronix TROVE T3SSK7528 installation guide
Cooper Wheelock
Cooper Wheelock Series 43T AC Bells specification
Logitech
Logitech Alert 700e Guide System Support Guide
ETS
ETS STW1-W4 instruction manual
Syscom Video
Syscom Video FASTRAX IV instruction manual
MAX SMART
MAX SMART SG2 Installation and user manual
