Vermont Castings VC50 User manual

Gas Barbecue Grill
For Models VC50 and VC75
50000621/1200
VERMONT
Castings
VERMONT
Castings
VERMONT
C
astings
VERMONT
C
astings
USERS MANUAL

Page i
Warnings
FOR YOUR SAFETY
If you smell gas:
• Shut off gas to the appliance
• Extinguish any open flame
• Open lid
• If odor continues, immediately call your gas supplier or fire department.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
An LP cylinder not connected for use shall not be stored in the vicinity
of this or any other appliance.
•Always read and understand the WARNINGS and SAFETY INSTRUCTIONS that are contained
in this Manual before attempting to use this Gas Barbecue Grill, to prevent possible bodily
injury or property damage.
•Always keep this Manual in or near the Grill, for convenient future reference.

SIGNAL WORDS :
The Signal Words used in this Manual, and their intended meanings, are as follows :
DANGER : Indicates that a failure to observe the safety instructions could result in death or catastrophic
bodily injury.
WARNING : Indicates that a failure to observe the safety instructions could result in serious bodily injury.
CAUTION : Indicates that a failure to observe the safety instructions could result in property damage or
minor bodily injury.
NOTE : Designates important information relating to the safe use of the Grill.
IMPORTANT WARNINGS :
Since this outdoor cooking appliance is movable, is fueled by natural or propane gas, generates very high
temperatures for cooking and emits carbon monoxide as a bi-product of combustion, prudent precautions
must be taken to assure its safe use.
•DANGER : This Grill has been designed for OUTDOOR use only.
Never use this outdoor Grill inside any building, garage, shed or breezeway, or inside any
boat, trailer or recreational vehicle, to prevent a possible fire and to prevent the possibility of
carbon monoxide poisoning or asphyxiation
•DANGER : Exposing an over-filled or a disconnected propane cylinder to heat could cause venting of
fuel through the pressure release valve. Since propane vapor is heavier than air it tends to pool and, if
ignited, could produce a violent fire or explosion.
Never install a propane cylinder if it is more than 80 % full, as the contents may lack adequate room for
expansion when exposed to heat.
Never store a spare Propane Gas Cylinder in the cylinder compartment of this Grill, because it will be exposed
to high temperatures when the Grill is in use.
This Gas Barbecue Grill will provide you with many hours of pleasure and enjoyment, if it is used in
accordance with the Warnings and Safety Instructions contained in this Manual.
The essential Warnings and Safety Instructions are located throughout the pages of this Manual, but some of
the principal ones have been summarized below for your convenience:
Page ii
Warnings

Page iii
Warnings
A. SAFE LOCATIONS FOR USE OF THIS OUTDOOR GRILL
DANGER :
•Never use this outdoor Grill inside any building, garage, shed or breezeway, or inside any boat, trailer
or recreational vehicle, to prevent a possible fire and to prevent the possibility of carbon monoxide
poisoning or asphyxiation.
WARNINGS :
•Always confirm that this Grill is not positioned under a combustible object (e.g., an awning or
umbrella) or in a covered area (e.g., a porch or gazebo) before lighting it, to prevent a possible fire.
•Always confirm that this Grill is not positioned under the overhang of a house, a garage or other
structure before lighting it. An overhang will serve to deflect flareups and radiated heat into the
structure itself, which could result in a fire.
•Always confirm that this Grill is positioned more
than 36” (1m) away from any combustible
materials or surfaces before lighting it, and that
no gasoline or other volatile substances are
stored in the vicinity of this Grill. The tempera-
ture of a grease fire or of the radiated heat might
otherwise be sufficient to ignite nearby combus-
tibles or volatile substances.
•Always locate this Grill where there will be ample
combustion and ventilation air, but never
position it in the direct path of a strong wind.
•Never allow the Grill to operate while unat-
tended, to prevent uncontrolled grease fires from
erupting.
Never attempt to move this Grill while it is in opera-
tion or while it is still hot, to prevent possible
personal injury.
• Never store or use gasoline or other flammable or volatile substances in the vicinity of this Grill or in the
vacinity of any other heat-generating appliance, because of the danger of starting a fire.
• Always confirm that the installation of this Grill conforms with the requirements of all local Codes or, in the
absence of any applicable local Codes, with either the National Fuel Gas Code, ANSI Z223.1; CAN/CGA-
B149.1, National Gas Installation Code; or CAN/CGA-B149.2, Propane Installation Code.
Fig. 1
36" (1m)
36" (1m)

B. SAFE USE OF LP (PROPANE) GAS
DANGER :
•Never install a propane cylinder that is more than 80 % full, as the contents may lack adequate room
for expansion when exposed to heat. Propane vapor may then be vented through the pressure release
valve, which could accumulate in a pool and later result in a fire or explosion.
Always instruct your certified propane fuel supplier to confirm by weight that your cylinder is not more
than 80 % full. An empty cylinder will weigh about 18 lbs., while a properly filled cylinder should weigh
no more than 38 lbs.
•Never store a spare Propane Cylinder in the cylinder compartment of this Grill. Exposing a discon-
nected cylinder to heat could result in the venting of propane vapor through the pressure release valve,
and the pooled vapor could result in a violent fire. (No hazard is posed by the connected cylinder if it is
not overfilled, however, as it tends to refrigerate itself while it is being used.)
Always confirm that all openings in the cylinder compartment of this Grill are free of any obstructions
that would restrict the circulation of ventilation air. Good ventilation will prevent the pooling of leaked
propane vapor, which is heavier than air, and which could explode if ignited.
WARNINGS :
•Always consult the Rating Label on the back of the Grill to confirm which fuel must be used with the
Grill. Never operate the Grill with propane gas if it has been configured to use natural gas, to prevent
hazardous overheating.
•Always confirm that there are no gas leaks before lighting this Grill. Apply a 50/50 solution of liquid
soap and water to the gas supply line connectors with a brush or spray bottle, and watch for bubbles.
Never use a match or open flame to test for gas leaks.
•Always visually inspect the gas supply line for fraying, cracking or rodent damage before each use of
this Grill and, if necessary, install a replacement obtained from your Vermont Castings dealer before
lighting this Grill.
Always store your spare Propane Gas Cylinders in an outdoor area that is well-ventilated, shady, cool and
removed from any heat source. Always store those cylinders in an upright position. Never store a spare
cylinder in the vicinity of this Grill, or in the vicinity of any other heat-generating appliance.
Page iv
Warnings
C. SAFE USE OF NATURAL GAS
• Always consult the Rating Label on the back of the Grill to confirm which fuel must be used with the
Grill. Never attempt to operate the Grill with natural gas if it has been configured to use propane gas, to
prevent possible bodily injury.
• Always employ a qualified service agency to install all necessary gas supply plumbing, for safety reasons
and to assure compliance with all applicable Codes.

Safety
• Always promptly shut off the gas supply and immediately extinguish all flames if you smell gas. Always
seek assistance from your gas supplier or local Fire Department if the gas smell persists, because of the
danger of fire or explosion.
• Always confirm that there are no gas leaks before lighting this Grill. Apply a 50/50 solution of liquid
soap and water to the gas supply line connectors with a brush or spray bottle, and watch for bubbles.
Never use a match or open flame to test for gas leaks.
• Always visually inspect the gas supply line for fraying, cracking or rodent damage before each use of this
Grill and, if necessary, install a replacement before lighting this Grill.
• Never permit a gas supply line to contact any heated surface of this Grill.
D. PREVENTION OF BURNS
• Always keep children and pets under close supervision when using this Grill, and never permit them to
come near the Grill while it is in use, as the exterior surfaces will be very hot.
• Always wear insulated protective mitts when working at the Grill, or when attempting to close a gas
supply valve after cooking has been completed, to prevent possible burns. Always use insulated pot holders
when handling containers of hot food.
• Always wear an insulated protective mitt when adding a smoking agent to a Smoker Box.
• Never store or use gasoline or other flammable or volatile substances in the vicinity of this Grill, or in
the vicinity of any other heat-generating appliance.
E. ELECTRICAL SAFETY
• Always confirm that this Grill has been grounded in accordance with local Codes or, in the absence of
local Codes, with the National Electrical Code, ANSI/NFPA No. 70 or the Canadian Electrical Code, CSA
C22.1, when an external electrical source is being utilized for the Rotisserie Motor.
• Always use a grounded three-prong outlet and a three-prong extension cord to energize the Rotisserie
Motor. Never alter or remove the grounding prong on the Rotisserie Power Cord, as an electric shock
hazard would then result.
• Never permit an electrical supply cord to contact any heated surface of this Grill.
Page v

Table of Contents
Page 1
Safety Important Warnings.................................................................... i - v
Clearance Requirements ............................................................. ii
Table of Contents........................................................................ 1
Fuels ........................................................................................... 2
Safey ........................................................................................... 3
Gas Hookup Hooking Up to the Gas Supply..................................................... 4
LP Gas Supply Connection ........................................................... 4
Natural Gas Supply Connection.................................................... 5
Test for Leaks.............................................................................. 5
Operation Control Functions ........................................................................ 6
Lighting the Main Burners........................................................... 7
Turning the Burners Off .............................................................. 8
Flareups...................................................................................... 8
Match Lighting the Main Burner.................................................. 8
Lighting the Rotisserie Burner..................................................... 10
Match Lighting the Rotisserie Burner .......................................... 10
Rotisserie Setup .......................................................................... 11
Lighting the Side Burner.............................................................. 12
Shutting the Side Burner Off........................................................ 12
Using the Smoker Box................................................................. 13
Cooking Methods of Cooking..................................................................... 14
Preparing Food for the Grill ........................................................ 15
Grilling Tips ................................................................................ 16
Cooking Time Chart..................................................................... 17
Care & Burners....................................................................................... 20
Cooking Grids ............................................................................. 21
Drip Tray..................................................................................... 22
Stainless Steel Panels................................................................... 22
Porcelain Enamel Castings .......................................................... 22
Burner Adjustment...................................................................... 23
Trouble Shooting Guide .................................................................................. 24
Maintenance

Safety
Fig. 3
Fig. 2
Page 2
Check hose for breaks
or wear before each use
Type I
Connector
Regulator
Shutoff
Valve
Collar
WARNING: Use only the pressure regulator and and type I propane
gas supply coupling and hose that is originally provided with this
appliance or as specified by Vermont Castings, (see Fig. 2).
ADDITIONAL WARNINGS:
• Always install a 20 lb. propane cylinder that is equipped with a
type I valve outlet (see Fig. 3), and that has a 12” diammeter and
an 18” height. Always use a propane cylinder that has been
constructed and marked in conformance with either the
spectifications for LP Gas Cylinders of the U.S. Department of
Treasportation or the spectifications in the National Standard of
Canada, CAN/CSA-B339, Cylinder, Spheres and Tube for
Transportation of Dangerous Goods, as applicable.
• Always confirm that your propane cylinder is equipped with a
shut-off valve terminating in a Type I propane cylinder valve outlet
connection, and that it has been provided with a collar to protect
the cylinder valve.
• Never install a propane cylinder in this Grill unless it is
equipped with a listed Overfill Protection Device (OPD).
• Always have a new propane cylinder properly purged of air by
your certified propane gas dealer. Since a new cylinder is initially
filled with air, the air must first be purged before it is filled with
propane.
• Always visually inspect the gas supply line for fraying, cracking
or rodent danaged before each use of this Grill and, if necessary,
install a replacement obtained from your Vermont Castings dealer
prior to lighting this Grill.
Fuels
WARNING : Never use Natural Gas in a Grill that has been configured to burn Propane Gas, and never use
Propane Gas in a Grill that has been configured to use Natural Gas, to avoid possible bodily injury. Always
consult the Rating Label on the back of your Grill to confirm which fuel must be used with the Grill.
NOTE: Your Vermont Castings Gas Grill has been specifically equipped at the factory to burn either Propane
Gas (LP) or Natural Gas (NG). The Grill may be converted for safe use with the alternative fuel, however,
through the installation of an appropriate Fuel Conversion Kit, which is available from your Vermont Castings
dealer.

Safety
Page 3
DANGER:
a) Do not store a spare LP - Gas Cylinder under or near this appliance
b) Never fill the cylinder beyond 80% full; and
c) If the information in a) and b) is not followed exactly, a fire causing death or serious injury may occur.
WARNING : Always confirm that the openings in the cylinder compartment of the Grill are free of any
obstructions that would restrict the circulation of ventilation air. Good ventilation will prevent any possible
accumulation of leaked propane vapor, which is heavier than air and which could explode if ignited.
NOTE : Always have a certified propane gas supplier inspect and requalify your refillable propane gas
cylinder prior to each refilling, in accordance with DOT or TC requirements for propane cylinders.
ADDITIONAL WARNINGS :
•Always handle propane cylinders with great care, as the contents are under high pressure.
•Always close the propane cylinder valve promptly after each use of the Grill.
•Always store propane cylinders outdoors, in an upright, secure position, out of direct sunlight, away
from living quarters and in a well-ventilated, cool, dry area. NEVER STORE A CYLINDER IN A BUILD-
ING, GARAGE OR OTHER STRUCTURE OR ENCLOSED AREA.
•Always keep cylinders out of reach of children.
•Always confirm that a valve dust cap has been tightly installed and that the valve itself is fully closed,
whenever a propane cylinder has been disconnected.
•Always transport a propane cylinder in an upright, secure position, after confirming that its valve is
closed.
•Always stabilize a cylinder so that it cannot move, when it is being transported in a car trunk.
•Never transport a propane cylinder in the passenger compartment of a car or truck.
•Never store a Vermont Castings Gas Grill indoors, unless the propane cylinder has first been discon-
nected and removed from the Grill.
•Never expose a propane cylinder to any heat source, never apply heat directly to a cylinder and never
store a spare cylinder in the vicinity of this Grill.
•Never paint a propane cylinder a dark color, as this can cause the cylinder and its contents to over-
heat.
• The LP cylinder must be arranged for vapor withdrawal.

Gas Hookup
Fig. 4
Fig. 5
Page 4
VERMONT
C
astings
VERMONTVERMONT
C
astings
Hooking Up to the LP (Propane) Gas Supply
For Your Safety
1. WARNING : Never store or use gasoline or any
other volatile substance in the vicinity of this Grill.
2. WARNING : Never store a spare propane cylinder
in the vicinity of this Grill, or in the vicinity of any other
potential heat source.
LP (Propane) Gas Supply Connection
1. Always place the propane tank in the tank locator hole in the
bottom pan of the cylinder compartment.
2. Always confirm that all burner control knobs are in the OFF
position before activating the gas supply.
3. Always connect the gas supply regulator as follows :
• Insert the nipple of the valve coupling into the tank valve and
tighten the connection collar by turning it clockwise with one
hand while holding the regulator with the other, (see Fig. 4).
WARNING : Always conduct a leak test before lighting the Grill, to
prevent a possible fire or explosion (see page 5).

Natural Gas Supply Connection
To Connect:
1. Push back the Sleeve on the Socket as shown below (see Fig. 6a).
2. Insert Plug and release the Sleeve (see Fig. 6b).
3. Push the Plug until Sleeve snaps forward to lock
the Plug in the Socket.
• WARNING : Always conduct the following safety
tests before lighting the Grill, to prevent a possible
fire or explosion (see leak test below)
To Disconnect:
1. Push Sleeve back and pull the Plug out.
Fig. 6a
Release Sleeve
Fig. 6b
Gas Hookup
Retract Sleeve
Release Sleeve
Page 5
Testing For Gas Leaks
Before attempting to operate this Grill :
1. Always confirm that all burner control knobs are
in the OFF position.
2. Always connect the gas supply hose first and then open the gas shutoff valve.
3. Always use a brush or spray bottle to apply a 50/50 solution of liquid soap and water to all connection
points (see Fig. 5) to test for gas leaks. Never use a match or open flame for that purpose.
4. Always look for bubbles to appear, as the appearance of bubbles will indicate a gas leak. Always turn off
the gas immediately and tighten the connection, if you find that a leak exists.
5. Always repeat this procedure until no further gas leaks are found to exist, before lighting the Grill.
6. Never attempt to light this Grill, however, if a leak cannot be stopped. Always call your propane gas
supplier promptly to obtain assistance.
WARNINGS :
• Always consult the Rating Label on the back of the Grill to confirm that it has already been configured to burn Natural
Gas. If it is necessary to reconfigure the Grill, however, always utilize the Natural Gas Fuel Conversion Kit available from
your Vermont Castings retailer, to prevent possible bodily injury.
• All gas suppy plumbing should be performed only by a qualified service agency. In the U.S., the supply connection
must be made in accordance with local code or, in the absence of local codes, with the national fuel gas codes, ANSI
Z223.1. In Canada, the supply connection shell be carried out in accordance with the provincial authorities having
jurisdiction and in accordance with the requirements of the CAN/CGA 1-B149.1 AND .2 installation code. A shut-off
value must be installed between the gas grill and the main supply. For natural gas, use a 3/8” or 1/2” natural gas supply
line capable of an a input of at least 60,000 BTU’S.
• Always disconnect the Grill and close its individual manual shutoff valve, when conducting pressure tests of the gas
supply piping system at pressures which exceed 1/2 psi (3.5kPa).
• Always isolate the Grill from the gas supply piping system by closing its individual manual shutoff valve when
conducting pressure tests of the gas supply piping system at pressures which are equal to or less than 1/2 psi (3.5kPa).

Control Functions
Operation
Page 6
Propane Tank Valve
WARNING : Never open the Tank Valve unless the Grill is being prepared for use, to prevent the pooling of
propane vapor.
Always open the Valve immediately before lighting the Grill, and always close it immediately after cooking has
been completed.
Burner Control Valves
On Model VC75, three valves independently control gas flow to the Left, Right, and Rotisserie burners, as
indicated on the front Control Panel (see Fig. 7).
On Model VC50 there are two independent control valves for the main burners.
The OFF position is indicated by the dot above each knob. A full range of flame adjustment is available from
High to Low, (by turning a knob counterclockwise).
Piezo Ignition System
As you turn the Ignitor knob clockwise, you will hear a click as the Piezo module generates an ignition spark
to the burners. The burner should light within four clicks.
Models VC200 & 400
Fig. 7
BUTTON

Lighting the Main Burners
Fig. 8
Fig. 9a Fig. 9b Fig. 9c
Normal: Soft blue flames Out of Adjustment: Hard blue
flames-too much air Poor Combustion: Wavy, yellow flames-too little air
Page 7
1. Always open the Hood completely and always inspect the Grill
and burners to confirm that all components are properly
positioned, before lighting the main burners.
WARNING: Never stand with your head directly over the Grill
when preparing to light the main burners, to prevent possible
bodily injury.
2. Always confirm that all of the burner control knobs are in the
OFF position before opening the gas supply.
3. Turn on the propane gas supply valve at the tank (1 to 2 turns)
or turn on the main natural gas supply valve, (see Fig. 8).
4. Turn the selected Burner Control Knob to the HI position by
pushing down on the knob and turning it counterclockwise.
5. Immediately turn Igniter Button. The selected burner should
light within four clicks.
• WARNING: IF THE SELECTED BURNER DOES NOT LIGHT, immediately turn the burner control knob to the OFF
position, to prevent gas buildup. Wait five (5) minutes for the gas to clear and then repeat the preceding starting
procedure. If the burner will not light when using the Igniter, follow the match lighting instructions (see Page 9).
6. Confirm that the burner is properly lit and that the flame pattern is as desired, (see Figs. 9a, 9b & 9c, for the proper
flame patterns). If the flame pattern is other than normal, consult the Troubleshooting Guide on Page 26 for correc
tive action.
7. Always preheat the grill before starting cooking. Light both burners and adjust them to the HI position for 5 to 10
minutes. Before placing any food on the Grill, clean the cooking grids with a brass wire brush.
8. Adjust the Controls to a medium setting for most cooking requirements. A light coating of cooking oil on the cooking
grids, before heating the Grill, will prevent foods from sticking to the Grill.
VERMONT
Castings
VERMONT
C
astings
Operation

Lighting the Oven Burner (Models VC200 & VC400)
Operation
Page 9
Use of the Oven burner is ideal for the convection cooking of roasts, seafood, vegetables and pizzas.
To start the Oven burner :
1. Always open the Hood completely, before attempting to light the Grill.
WARNING : Never stand with your head directly over the Grill when preparing to light the Oven burner, to
prevent possible bodily injury.
2. Always confirm that all of the burner control knobs are in the OFF position, before opening the gas supply.
3. Turn on the propane gas supply valve at the tank (1 to 2 turns) or turn on the main natural gas supply
valve.
4. Turn the Oven Burner Control Knob to the HI position by pushing down on the knob and turning it
counterclockwise.
5. Immediately push the Igniter Button. The Oven burner should light within four seconds.
•WARNING :
IF THE OVEN BURNER DOES NOT LIGHT, immediately turn the burner control knob to the
OFF position, to prevent gas buildup. Wait five (5) minutes for the gas to clear and then repeat the
preceding starting procedure. If the Oven burner will not light when using the Igniter, first ignite one
of the main burners and then turn on the Oven burner. Turn off the main burner once the Oven burner is lit.
6. Confirm that the burner is properly lit and that the flame pattern is as desired (see Figs. 9a, 9b & 9c, for
the proper flame patterns). If the flame pattern is other than normal, consult the Troubleshooting Guide
on Page 26 for corrective action.
7. Always preheat the Grill before starting cooking.
8. Adjust the Control to a medium setting, for most cooking requirements.
WARNING : Never use the main burners while using the Oven burner, as that could result in overheat your
Grill.

Operation
Lighting the Rotisserie Burner (Model VC75)
Fig. 11
Page 10
The Rotisserie burner provides the steady, even heat required to cook poultry and roasts to self-basted perfection.
To start the Rotisserie burner :
1. Always open the Hood completely before attempting to light the Grill.
WARNING : Never stand with your head directly over the Grill when preparing to light the Rotisserie burner,
to prevent possible bodily injury.
2. Always confirm that all of the burner control knobs are in the OFF position before opening the gas supply.
3. Turn on the propane gas supply valve at the tank (1 to 2 turns) or turn on the main natural gas supply valve.
4. Turn the Rotisserie Burner Control Knob to the HI position, by pushing down on the knob and turning it
counterclockwise.
5. Immediately turn the Igniter Button. The Rotisserie burner should light within four clicks.
•WARNING : IF THE ROTISSERIE BURNER DOES NOT LIGHT, immediately
turn the burner control knob to the OFF position, to prevent gas buildup.
Wait five (5) minutes for the gas to clear and then repeat the preceding
starting procedure. If the burner will not light when using the Piezo
Igniter, follow the match lighting instructions below.
6. Confirm that the burner is properly lit and that the flame pattern is as
desired, (see Figs. 9a, 9b & 9c, for the proper flame patterns). If the
flame pattern is other than normal, consult the Troubleshooting
Guide on Page 26 for corrective action.
7. Always preheat the Grill before starting to cook on the rotisserie.
Match Lighting the Rotisserie Burner
1. Always open the Hood completely, before attempting to light the Grill.
WARNING : Never stand with your head directly over the Grill when
preparing to light the Rotisserie Burner, to prevent possible bodily injury.
2. Always confirm that all of the burner control knobs are in the OFF
position before opening the gas supply.
3. Turn on the propane gas supply valve at the tank (1 to 2 turns) or
turn on the main natural gas supply valve.
4. Insert a lit match or a butane lighter into the match lighting hole located
below the rotisserie screen (see Fig. 11).
5. Turn the Rotisserie Control Knob to the HI position by pushing down on the
knob and turning it counterclockwise.
VERMONT
C
astings
VERMONTVERMONT
C
astings
Rotisserie
Lighting Hole

Rotisserie Setup (Optional to Model VC50 & VC75)
Fig. 12
Operation
Page 11
The Rotisserie burner is intended to be used for rotisserie cooking only.
WARNING : Never use the main burners while using the Rotisserie burner, as that could result in igniting the
drippings, or overheating your Grill.
The Rotisserie assembly includes a
counter-weight for large or irregular
food items ; using the counterweight
will reduce the strain on the motor.
1. Remove the warming rack. Lay a flat
pan directly on the cooking grates to
catch drippings. Large food items
may require that you remove the
cooking grates and place the pan on
the sear plates.
2. Insert the ends of the Rotisserie
Support into the slots of the right
cooking grate, so that the edge of the
support is approximently 1” from the
right casting, and the top groove is in
line with the rotisserie spit hole in the left casting (see Fig. 12).
3. Engage the Motor Bracket into the Bracket guide on the inside edge of the left shelf.
4. Engage the Rotisserie Motor in the Motor Bracket (see Fig. 12).
5. Assemble the spit and meat forks. Adjust the retainer bushing to keep the spit in place (see Fig. 12).
Tighten the thumbscrews with small pliers.
Always use the counterweight to balance the spit when cooking large or irregular food items.
The Rotisserie Motor is rated to turn a maximum load of 12 lbs.
WARNINGS :
Never use the Rotisserie Motor in the rain, and never use it if it has become wet.
• Always use a grounded three-prong outlet and a three-prong extension cord to energize the Rotisserie
Motor. Never alter or remove the grounding prong on the Rotisserie Power Cord, as an electric shock hazard
would then result.
Never permit an electrical supply cord or a gas supply line to contact any heated surface of this Grill.
VERMONT
C
astings
Rotisserie
Motor
Rotisserie
Bracket
Rotisserie
Forks
Rotisserie
Support
Bushing
VERMONT
C
astings

Operation
Lighting the Side Burner (Optional to Models VC50 & VC75)
Fig. 13
O
F
F
HI
LO
IGNITOR VALVE CONTROL
Page 12
WARNING : Never stand with your head directly over the Grill when preparing to light the side burner, to
prevent possible bodily injury.
1. Turn the side burner control knob to HI (see Fig. 13).
2. Turn the Igniter Knob clockwise until the burner ignites. The burner
should light within four clicks of the igniter.
NOTE: Observe the flame pattern. Soft blue flames are normal ; hard blue
flames or wavy yellow flames are not. You can adjust the flame with the air
shutter below the control knob (see Fig 19). If yellow flames persist, refer to
the Troubleshooting Guide on Page 26.
Shutting the burner off
1. Turn the control knob counterclockwise to the HI position, then depress it and turn it to OFF. NEVER force
the knob without depressing it, as that can damage the valve.

Using the Smoker Box (Model VC75)
Fig. 14
Operation
Page 13
The VC75 model Grill is equipped with a Rotisserie Burner Smoker Box. You can add a distinct, smoky flavor
to your food by burning a variety of woods or herbs in this unit.
1. Always soak any wood chips or herbs that you wish to smoke for a half-hour or more.
2. Always pre-warm the Grill before adding your smoking agent to the Smoker Box.
3. Remove the lid from the Smoker Box with a pair of tongs, or while wearing an insulated protective mitt
and place some of the presoaked material in it (see Fig. 14).
4. Use low or medium heat for smoking.
5. Use a marinade with drier foods to benefit the smoking process and to enhance the flavor of your smoked
dishes.
WARNING : Always wear an insulated protective mitt when adding a smoking agent to the Smoker Box,
to prevent burns.
Rotisserie Burner Smoker Box

Methods of Cooking
With its combination of burners and accessories your Vermont Castings gas grill
can provide for virtually every conceivable style of cooking.
• The powerful Main burners deliver the middle and high range of tempera-
tures desired for traditional barbecuing. This includes searing and finishing
steaks, hamburgers, pork chops and the like, or grilling chicken parts,
sausages, or kebabs with more moderate heat (see Fig. 15a).
• The Rotisserie burner standard on Model VC75, delivers the succulent self-
basted flavours of chickens, ducks and hams or pork, beef and lamb roasts
that only rotissing can achieve. Also the radiant infrared unit ensures that you
will be enjoying the results much sooner (see Fig. 15b).
• The optional Side burner boils sautés, stir fries or warms all with equal
aplomb. Plus its high power is more than adequate for deep frying seafood,
vegetables and meats or hard boiling soups, lobsters or corn on the cob (see
Fig. 15c).
• The optional Smoker Box, standard with all Vermont Castings gas grills
allows you enhance the flavors of foods by slow smoking with herbs, or a
variety of wood chips or chunks (see Fig. 14).
• The optional Vermont Castings Griddle pan accessory extends your
capabilities again. With this item you can pan fry eggs and bacon, potatoes
or seafood. Or if you prefer use it to grill fish steaks, other seafood or
lamb chops.
ROTISSERIE
Fig. 15a
Fig. 15b
Fig. 15c
Cooking
Page 14

One of the keys to extending your range of grilling capabilities is a fundamental understanding of the two
common methods of cooking, Direct and Indirect cooking.
In the Direct cooking method foods are placed directly above the heat source. This method is used in
searing for example where you require high and immediate heat to quickly brown the outside layer of meats
thereby sealing in their juices to enhance flavor. On the Vermont Castings grill this is accomplished using one
or both of your main burners and placing the food on the porcelain cooking grids directly over the burners.
This may be done with the grill hood either open or closed.
In the Indirect cooking method foods are placed on the grill offset from the heat source . With the grill lid
closed reflected heat surrounds the food cooking it more evenly and gently. This approximates the action of a
convection oven where heat is circulated by the use of a fan to achieve a similar result. This method is perfect
for cooking roasts of any kind but is also useful whenever you want to slow cook or bake a wide variety of
foods. Indirect cooking on your Vermont Castings grill is accomplished using one of the main burners and
placing the food on the porcelain cooking grid above the opposite burner, or on the warming rack burner.
The grill hood should always be closed when employing the indirect cooking method
Preparing Food for the Grill
Cooking
Page 15
WARNING: Always observe safe food-handling and safe food-preparation practices when using this Grill, to
prevent food-borne illnesses :
• Always cook foods adequately. Undercooked foods can retain bacteria, especially if thawed or exposed to
warm conditions prior to cooking.
• Always use a meat thermometer to confirm that foods have been fully cooked.
• Always use separate plates and utensils for the handling of raw food. Never place raw food and cooked
food on the same plate, and never place cooked food on a plate that was used for handling raw food.Al
ways carefully wash all plates and utensils used to handle raw food before using them to handle cooked
food.
• Always wash all vegetables, seafood and poultry before cooking.
• Always leave uncooked foods in the refrigerator until you are ready to start cooking.
• Always marinate meat in the refrigerator. Always dispose of the excess marinade, and never reuse it.
• Always preheat your Grill for 5 to 10 minutes before cooking, and clean off all grease and food residue
before using the cooking grids.