Versatile AutoBoom SX275 User manual

Versatile SX275 AutoBoom™
Installation Manual
Manual No. 016-0230-097 Rev. H 03/17 E29365
Copyright 2017

While every effort has been made to ensure the accuracy of this document,
Raven Industries assumes no responsibility for omissions and errors. Nor is any
liability assumed for damages resulting from the use of information contained
herein.
Raven Industries shall not be responsible or liable for incidental or consequential
damages or a loss of anticipated benefits or profits, work stoppage or loss, or
impairment of data arising out of the use, or inability to use, this system or any of
its components. Raven Industries shall not be held responsible for any
modifications or repairs made outside our facilities, nor damages resulting from
inadequate maintenance of this system.
As with all wireless and satellite signals, several factors may affect the availability
and accuracy of wireless and satellite navigation and correction services (e.g.
GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the
accuracy, integrity, continuity, or availability of these services and cannot
guarantee the ability to use Raven systems, or products used as components of
systems, which rely upon the reception of these signals or availability of these
services. Raven Industries accepts no responsibility for the use of any of these
signals or services for other than the stated purpose.
Disclaimer

Table of Contents
Manual No. 016-0230-097 Rev. H i
Chapter 1 Important Safety Information............................................................................. 1
Hydraulic Safety ...........................................................................................................................................................2
Electrical Safety ............................................................................................................................................................2
Chapter 2 Introduction............................................................................................................. 3
Introduction ...................................................................................................................................................................3
Preparing for Installation ..........................................................................................................................................4
Recommendations .................................................................................................................................................................4
Point of Reference .................................................................................................................................................................4
Hydraulic Fittings .........................................................................................................................................................4
Updates ...........................................................................................................................................................................5
Chapter 3 PowerGlide Plus...................................................................................................... 7
PowerGlide Plus Kit Contents .................................................................................................................................7
Install the PowerGlide Plus Hydraulic System ................................................................................................11
Remove the Orifice Fittings ..............................................................................................................................................11
Install Fittings on the AutoBoom Valve .......................................................................................................................14
Mount the AutoBoom Valve ............................................................................................................................................14
Install the Left and Right Cylinder Up Hoses .............................................................................................................16
Install the Left and Right Cylinder Down Hoses .......................................................................................................17
Hydraulic Schematic ............................................................................................................................................................19
Remove the Boom Stops .......................................................................................................................................21
Install the Gauge Wheels .......................................................................................................................................21
Gauge Wheel Mounting Locations ................................................................................................................................21
Install the PowerGlide Plus Wiring .....................................................................................................................22
Install the AutoBoom Node .............................................................................................................................................23
Connect the Harness Cable to the Boom Function Controls ..............................................................................23
Connect the Harness Cable to the Controller Cable ..............................................................................................24
Connect the Controller (If Applicable) .........................................................................................................................24
Connect the Field Computer (If Applicable) ..............................................................................................................24
Connect the Power Leads .................................................................................................................................................25
PowerGlide Plus Wiring Schematics ..................................................................................................................26
AutoBoom Controller .........................................................................................................................................................26
SCS 4000/5000 ......................................................................................................................................................................27
Viper Pro & Envizio Pro .....................................................................................................................................................28
Chapter 4 UltraGlide............................................................................................................... 29
UltraGlide Kit Contents ..........................................................................................................................................29
Install the UltraGlide Hydraulic System ...........................................................................................................33
Install Fittings on the AutoBoom Valve .......................................................................................................................33
Mount the AutoBoom Valve ............................................................................................................................................34
Install the Left and Right Cylinder Up Hoses .............................................................................................................36
Install the Left and Right Cylinder Down Hoses .......................................................................................................37
Install the UltraGlide Sensors ...............................................................................................................................40
Boom Sensor Mounting Locations ................................................................................................................................40
Mount the Center Rack Sensor .......................................................................................................................................41
Connect the Sensor Cables ...............................................................................................................................................41

Table of Contents
ii Versatile SX275 AutoBoom™ Installation Manual
Remove the Boom Stops ........................................................................................................................................42
Install the Gauge Wheels - Optional .................................................................................................................42
Gauge Wheel Mounting Locations ...............................................................................................................................42
Install the UltraGlide Wiring ..................................................................................................................................43
Install the AutoBoom Node .............................................................................................................................................44
Connect the Harness to the Boom Function Controls ...........................................................................................44
Install the Center Rack Control .......................................................................................................................................45
Connect the Harness Cable to the Sensors ...............................................................................................................46
Connect the Harness Cable to the Controller Cable ..............................................................................................46
Connect the Controller (If Applicable) .........................................................................................................................46
Connect the Field Computer (If Applicable) ..............................................................................................................46
Connect the Power Leads .................................................................................................................................................47
UltraGlide Wiring Schematics ...............................................................................................................................48
AutoBoom Controller .........................................................................................................................................................49
SCS 4000/5000 ......................................................................................................................................................................50
Viper Pro & Envizio Pro .....................................................................................................................................................51
Chapter 5 Replacement Parts............................................................................................... 53
Valve ...............................................................................................................................................................................53
Sensors ..........................................................................................................................................................................54

CHAPTER
1
Manual No. 016-0230-097 Rev. H 1
C hapt er 1 Important Safety
Information
Read this manual and the operation and safety instructions included with your implement and/or controller
carefully before installing the AutoBoom™ system.
•Follow all safety information presented within this manual.
•If you require assistance with any portion of the installation or service of your Raven equipment, contact
your local Raven dealer for support.
•Follow all safety labels affixed to the AutoBoom system components. Be sure to keep safety labels in good
condition and replace any missing or damaged labels. To obtain replacements for missing or damaged
safety labels, contact your local Raven dealer.
When operating the machine after installing AutoBoom, observe the following safety measures:
•Be alert and aware of surroundings.
•Do not operate AutoBoom or any agricultural equipment while under the influence of alcohol or an illegal
substance.
•Remain in the operator’s position in the machine at all times whenAutoBoom is engaged.
•Disable AutoBoom when exiting from the operator’s seat and machine.
•Do not drive the machine withAutoBoom enabled on any public road.
•Determine and remain a safe working distance from other individuals. The operator is responsible for
disabling AutoBoom when the safe working distance has diminished.
•Ensure AutoBoom is disabled prior to starting any maintenance work on AutoBoom or the machine.
•When starting the machine for the first time after installing AutoBoom, be sure that all persons stand clear,
in case a hose has not been properly tightened.
•The machine must remain stationary and switched off, with the booms unfolded and supported, during
installation or maintenance.
NOTICE
WARNING

Chapter 1
2 Versatile SX275 AutoBoom™ Installation Manual
Hydraulic Safety
•Raven Industries recommends that appropriate protective equipment be worn at all times when working on
the hydraulic system.
•Never attempt to open or work on a hydraulic system with the equipment running. Care should always be
taken when opening a system that has been previously pressurized.
•When disconnecting the hydraulic hoses or purging is required, be aware that the hydraulic fluid may be
extremely hot and under high pressure. Caution must be exercised.
•Any work performed on the hydraulic system must be done in accordance with the machine manufacturer’s
approved maintenance instructions.
•When installing AutoBoom hydraulics or performing diagnostics, maintenance, or routine service, ensure
that precautions are taken to prevent any foreign material or contaminants from being introduced into the
machine’s hydraulic system. Objects or materials that are able to bypass the machine’s hydraulic filtration
system will reduce performance and possibly damage the AutoBoom hydraulic valve.
Electrical Safety
•Always verify that the power leads are connected to the correct polarity as marked. Reversing the power
leads could cause severe damage to the equipment.
•Ensure that the power cable is the last cable to be connected.
CAUTION

CHAPTER
2
Manual No. 016-0230-097 Rev. H 3
C hapt er 2 Introduction
Introduction
Congratulations on your purchase of the RavenAutoBoom system! This system is designed to provide
automated boom height adjustment for agricultural spraying equipment.
This manual applies to the following machines. For future reference, write the serial number of your machine in
the space below.
MAKE: Versatile
MODEL: SX275
FIGURE 1. Versatile SX275
Note: This manual contains the installation instructions for the PowerGlide Plus and UltraGlide systems.
Be sure to identify which system you have and follow only the instructions for that system.

Chapter 2
4 Versatile SX275 AutoBoom™ Installation Manual
Preparing for Installation
Before installingAutoBoom, park the machine where the ground is level, clean, and dry. Leave the machine
turned off for the duration of the installation process.
During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.
Important: Do not allow the booms to rest on the on the boom stops during the calibration
process!
Recommendations
Raven Industries recommends the following best practices before installing or operating theAutoBoom system
for the first time, at the start of the season, or when moving the AutoBoom system to another machine:
•Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the
machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic
hoses, etc.).
•Operate each of the machine’s boom hydraulic functions (i.e., tilt, fold, center rack, tongue extension, or
other hydraulic valve functions) three times to ensure the machine’s hydraulic valve is using fresh oil and
debris is flushed from the hydraulic hoses, valves, and filters.
•Upon installation of the AutoBoom system, operate the boom and center rack raise/lower functions through
the machine’s manual control functions first before operating them via theAutoBoom controller/field
computer to ensure the hydraulic system has been installed correctly and air is released from the system.
Raven Industries recommends the following best practices when installing the AutoBoom system.
•Use part numbers to identify the parts.
•Do not remove the plastic wrap from a part until it is necessary for installation.
•Do not remove plastic caps from a part until it is necessary for installation.
Tools Needed
The following tools are recommended for installation of theAutoBoom system:
•SAE standard-sized wrenches
•Cable ties
•Set of tools
Point of Reference
The instructions in this manual assume that you are standing behind the machine, looking toward the cab.
Hydraulic Fittings
This manual may reference the following types of hydraulic fittings:
•SAE O-ring fittings

Manual No. 016-0230-097 Rev. H 5
Introduction
•ORFS (O-Ring Face Seal) fittings
•JIC fittings
Updates
Software and manual updates are available on the RavenApplied Technology website:
http://www.ravenhelp.com
At Raven Industries, we strive to make your experience with our products as rewarding as
possible. One way to improve this experience is to provide us with feedback on this manual.
Your feedback will help shape the future of our product documentation and the overall service
we provide. We appreciate the opportunity to see ourselves as our customers see us and are
eager to gather ideas on how we have been helping or how we can do better.
To serve you best, please send an email with the following information to
[email protected]
-Versatile SX275 AutoBoom™ Installation Manual
-Manual No. 016-0230-097 Rev. H
-Any comments or feedback (include chapter or page numbers if applicable).
-Let us know how long have you been using this or other Raven products.
We will not share your email or any information you provide with anyone else. Your feedback
is valued and extremely important to us.
Thank you for your time.
JIC fitting
ORFS fitting
SAE O-ring fitting

Chapter 2
6 Versatile SX275 AutoBoom™ Installation Manual