Versiton BHR40-V851 Assembly instructions

9. Power cable or video cable should be always loose.
Do not keep the cables tight or twisted.
10. Do not leave the unit along with an unstable stand or table.
11. Please use the camera unitwithin given temperature and electricity limit.
12. Please make sure thatinstallation should be done by qualified service
person only.
13. Donotdisassemble the unit by yourself. When there is problemwith
the unit please contact after-sale service center or the shop where
you bought.
1. Make a hole ofØ 25mm in diameter for passing cable.
2. Drill four holes on the wall or ceiling and insert the anchors.
3. Arrange the cables and fix the screws.
ACCESSORIES
DIMENSION
4. Attach the sunvisor and fix the sunvisor fixing bolt.
5.Loosenthe boltA, C-1and C-2 by using the 3mmwrench included.
6. Face the direction of the camera to monitor.
7. Tighen the bolt A, B, C-1, C-2 to complete adjustment.
1. Attach the bracket to the camera's bottom hole tightly.(In case of
installing the camera on the ceiling, attach the bracket to the
sunvisor fixing bolt hole on top of the camera.)
2. Fix the camera and bracket on the wall or ceiling.
1. New generation, new technology DSP adopted.
2. This camera is incredibly flexible toinstall with its 3-axis camera con-
struction, which makes the camera ceiling,wall or slope mountable.
3. This product is weather-proof to resist rain, snow and other weather
factors(IP66).
4. 40M range visible in total darkness with 40pcs of IR LEDs.(Indoor)
5. Supreme Resolution(700 TV-Line)
6. Day & Night function
7. Support 4 different privacy zone
8. DWDR(Digital Wide Dynamic Range)
9. Multi function : High Light Mask, Lens Shading Compensation, Motion
Detection
10. Dynamic IR : When IR LED is turned on in B/W, the objects can be
clearly identified due to the function thatdecreases screen saturation
of objects within a short distance.
11. Multi-language full OSD support
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED lightdirectly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface.
It will cause falling or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
(Use the AC adaptor 12V DC regulated, 1A)
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Due to the possibility of water leakage, do not cut or peel off the
cable. In case you cutor peel offthe cable,the warranty will be void.
8. Do not adhere dangerous articles to the camera.
CAUTION
FEATURE
IR WATERPROOF CAMERA
MANUAL
HOW TO INSTALL(Built-in bracket type)
HOW TO INSTALL(Stand bracket type - Option)
SCREW, 3EA
WRENCH
BOLT A
BOLT C-2
BOLT C-1
BOLT B
BOLT
SUNVISOR
207
102
61.5
Ø 6
Ø 25
ANCHOR 6x30, 4EA
SCREW Tp14x35, 4EA
ANCHOR 6x30, 4EA
SCREW 4x35 TP1PAN SUS, 4EA
WRENCH 3mm L TYPE, 1EA
SUNVISOR BOLT, 1EA
Extra video output cable for installation,
1EA(option)
BHR40-V851
Aurora

FUNCTION SETTING
1. How to use the jog lever
SPECIFICATION
※All specification is subject to change without notice to improve the quality.
1/3"SONY SUPER HAD CCD
768(H) X 494(V) PIXEL(NTSC), 752(H) X 582(V) PIXEL(PAL)
6.35 (H) X 7.4 (V)(NTSC), 6.5 (H) X 6.25 (V)(PAL)
2:1Interlace
Internal
700 TV-Line
48dB or More(AGC OFF)
1.0 Vp-p(Sync. Negative) Termination 75
0.1Lux(F/1.2), 0Lux(40M Range with 40pcs LED) - Indoor
γ= 0.45 typ.(0.45, 0.6, 1.0, user)
Yes(Multi Language)
ATW(2,500°K ~ 9,500°K)/MANUAL/AWC
1/60(1/50) ~ 1/100,000sec
BLC, DWDR, HLC(ON/OFF)
LOW/MIDDLE/HIGH/OFF
ON/OFF(64 Block)
ON/OFF(4 Zone)
ON/OFF
AUTO, COLOR, B/W(Electronic)
40pcs, Dynamic IR
ON/OFF
RS-485(Protocol : Pelco D, Pelco P)
Vari-focal auto iris lens
12V DC ±10%(24V AC :option)
Max.850mA(at 12V DC, 24V AC) : LED ON
-10℃~ 50℃
-20℃~ 60℃
61.5(W) X 61.5(H) X 102(D)mm
Approx. 900g
Ⅱ
㎛ ㎛ ㎛ ㎛
Ω
Model No.
Image Sensor
Effective Pixel
Cell Size
Scanning System
Sync. Type
Resolution
S/N
Video Output
OSD
AGC
Min. Illumination
Gamma
White Balance
Shutter Speed
Backlight
Motion Detection
Privacy Zone
Mirror
Day & Night
LED Brightness
DIS
Communication(option)
Lens
Power Supply
Current Consumption
Operation Temp.
Preservation Temp.
Dimension
Weight
Display each privacy mask or not. Press the
enter button to move into the privacy mask
setting section, whenever you press the enter
button, the mask color is changed. When the
mask color is red you can adjust the size by
up, down, left and right button. When the mask
color is blue you can set the position of mask
by up, down, left and right button. Press the
enter button for a few second to escape
Select mask color
Select the camera ID for RS-485communication
Select baud rate
Select protocol
Select language
Display the camera ID on the screen
Internal Sync with 12V DC power
Line-Lock(Not available)
Not available
OFF, ON
BLACK, GRAY…
1~ 255
2400 ~ 9600
ENGLISH, …
OFF, ON
INT
L/L
0 ~ 255
MASK
1, 2, 3, 4
CAM ID
BAUDRATE
PROTOCOL
LANGUAGE
SYNC
EDIT
POSITION
VPHASE
3. How to control through RS-485 communication(Option)
4. Cable array(Option)
1) Match the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is same as Up, Down, Left and
right of RS-485 controller
3)Enter ofJog lever is the same as menu key or IRIS open key ofRS-485
controller
4) Return to previous menu from motion detection setting section and
privacy mask setting section : Iris close or Iris open for a fewsecond.
Or press the button as Up Right Down Left successively→ → →
2. OSD menu structure
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
Function
RX +
RX -
Remark
RS-485A
RS-485B
No.
A
B
A : ORANGE(RX +)
B : WHITE(RX -)
6.PRIVACY
ZONE
MANUAL, DC
0 ~ 100
0 ~ 20
AUTO
OFF, LOW,
MIDDLE, HIGH
OFF, ON
OFF, ON,
AUTO
0 ~ 100
ATW
MANUAL
AWC
AUTO
COLOR
B&W
OFF, ON
85 ~ 170
50 ~ 135
3 ~ 15
OFF, ON
OFF, ON
0 ~ 50
OFF, ON
0 ~ 50
0 ~ 200
0 ~ 200
OFF, ON
NONE
MESSAGE
MASK
0 ~ 255
1~ 15
Fixed focal lens or Vari-focal auto iris lens
In case of manual lens selection, adjust the
brightness
In case ofDC lens selection, adjustthe brightness
Shutter speed auto adjustable
Select shutter speed manually
Determines that use the AGC function or not
and AGC level selectable(You can not use the
Auto D&N change mode when AGC is off)
Digital Wide Dynamic Range
BLC function
High Light Mask function
In case of AUTO mode, the function will off in
daytime and on at night
According to the threshold value, the camera
will recognize as High light or not.
Color temperature 2500 ~ 9500°K
Adjust the Red or Blue values to shiftthe color
of the object
Move the camera lens toward to white paper
then press the set button to find the optimal
white balance for current environment
Auto day&night switching mode
Fixed at color
Fixed at B/W
Determines whether to transmit the burst signal
or not in B/W mode
You can select brightness of illumination about
changing the day ↔night mode
You can select the duration time about chainging
the day ↔night mode
When IR LED is turned on in B/W, the objects
can be clearly identified due to the function
that decreases screen saturation of objects
within a short distance.
Set a horizontal image inversion
Sharpness adjustable
Gamma adjustable
Determines whether to use the brightness com-
pensation offour lens'corners(LSC) or not
The LSC level selectable
Adjust Red tone of the image
Adjust Blue tone ofthe image
Determines whether to use the motion detection
function or not
No display on the screen though movement is
detected
The words 'MOTION' appear on the screen
when movement is detected
Motion detection area appear on the screen
when movement is detected
Motion detection sensitivity
Set the duration of outside alarm. If the way of
display is message, it means display time of
message
LENS
E.SHUTTER
AGC
DWDR
BLC
HLC
AWB MODE
D&N MODE
DYNAMIC IR
MIRROR
SHARPNESS
GAMMA
LSC
R-Y GAIN
B-Y GAIN
MOTION
BRIGHT
DC LEVEL
HLC THR
BURST
DELAY TIME
LSC LEVEL
DISPLAY
SET
WINDOW
ALL SET
SENSITIVITY
HOLD TIME
Function
setting menu Select menu ContentsSub menu
1/60(1/50)~1/100,000
BW COLOR→
COLOR BW→
0.45, 0.6,1, USER
ALL CLEAR↓
1. EXPOSURE
3. DAY&NIGHT
4. IMAGE ADJ.
2. WHITE
BALANCE
5. ALARM
PATTERN
GENERATOR
ㆍThe ' ' icon appeared with desired function, press the set button to move sub menu.
ㆍThe '- - -' icon appeared with function that is unavailable according to function setting.
OFF, LOW, MIDDLE, HIGH
MASK COLOR
PELCO-D, PELCO-P
NAME DISPLAY
10. EXIT
8. SPECIAL
9. FACTORY
SET
7. COMMUNI-
CATION
(option)
To reset your camera to factory default condition
Notice : Lens, communication and language is not changed
Save the value and then restart
※If you change the COMMUNICATION value through RS-485, you might not
control the camera due to unmatched value(If your camera is out of working
due to above reason, change your controller's value or wait a few minute till
close the menu, it will be back to previous setting value)
Press the enter button to move into the name setting section.
You can choose the letter by using up and down button and
move next letter by using left and right button. Press the
button for a few second to move out
enter
Press the button to move into the position setting section.
You can move the camera ID to your wanted position by using
up, down, left and right button
enter
Test signal. Press the enter button, color bar appeared on the
screen and press any key to return to menu
Press the button to move into the motion detection area
section to the 64 areas. Press the button for a few
second to move out
Press the button to select all area
Press the button to remove all area
enter
enter enter
enter
enter
①ENTER :
②UP, ③DOWN :
④LEFT, ⑤RIGHT :
⑥FOCUS, ⑦ZOOM :
⑧EXT. VIDEO :
ㆍPush the lever : Used to access the
menu and confirm selection.
ㆍPush the lever for one second : Used
to return to previous menu from the
motion detection setting section or
privacy mask setting section.
Used to move the
cursor to up or down.
Used to move the
cursor to left or right and change the
value.
Use a '+' type
driver for adjusting zoomand focus.
(In case of operation Focus/Zoom,
don't put stress excessively.)
Extra video output terminal for installation. The cable
is option.
*OSD menu & Focus/Zoom
adjustment direction
1. Unfasten the screw of the
bottom door
2. Adjust the jog lever & Focus
/Zoom trimmers
3. Tighten the screw of the
bottom door
F
EXT.VIDEO
Z
7
6
8
2
5
13
4
BHR40-V851