Vertiv LIEBERT PSA itON-SOHO User manual

LIEBERT® PSA itON-SOHO
650/850/1000VA, 230V
User Manual
1Liebert® PSA itON-SOHO User Manual (R1/071621)
SETUP
1. Inspect the Package
Inspect the package and the UPS upon receipt. Notify the
carrier and dealer of visible damage.
2. Decide where to place the UPS
The UPS must be placed indoors, protected from water, direct
sunlight and excessive heat. Provide at least 7.8” (20 cm) of
clearance on all sides of the unit for proper ventilation.
3. Charge the UPS battery before use
The UPS battery is fully charged before shipping. However,
some charge may be lost during shipping and the battery
should be recharged prior to use.
• Plug in the AC input cord of the UPS to the wall outlet.
It is recommended to charge the battery at least 4 hours
before initial use. The unit charges its battery while
connected to the utility.
4. Start the UPS
After the battery is fully charged:
• Turn on the UPS by pressing the On/O button. (see figure
below) LED1 should be illuminated (green), indicating the
UPS is operating in Normal Mode.
5. Connect the loads
The UPS has dedicated backup outlets that provide power
when the UPS operates on battery. (see UPS Controls and
Connections on next page)
• Plug the loads into the battery backup outlets on the side
panel of the UPS
CAUTION: Never connect a laser printer or scanner to the UPS
unit. This may damage the unit.
IMPORTANT SAFETY INSTRUCTIONS
Save these instructions:
This manual contains important instructions that should be followed
during installation and maintenance of the UPS.
• Intended for installation in a controlled environment.
• Maximum ambient temperature 104°F (40°C)
CAUTION! To prevent the risk of fire or electric shock, install in a
temperature and humidity controlled indoor area free of conductive
contaminants. (See the specifications for the acceptable temperature
and humidity range.)
CAUTION! To reduce the risk of overheating the UPS, do not cover
the UPS’s cooling vents and avoid exposing the unit to direct sunlight or
installing the unit near heat emitting appliances such as space heaters or
furnaces.
CAUTION! Do not attach non-computer-related items, such as medical
equipment, life-support equipment, microwave ovens, or vacuum
cleaners to UPS.
CAUTION! Do not plug the UPS input into its own output.
CAUTION! Do not allow liquids or any foreign object to enter the UPS.
Do not place beverages or any other liquid-containing vessels on or near
the unit.
CAUTION! In the event of an emergency, press the OFF button and
disconnect the power cord from the AC power supply to properly disable
the UPS.
CAUTION! Do not attach a power strip or surge suppressor to the UPS.
CAUTION! If the UPS is with metal chassis, for safety purpose, grounding
is a must during UPS installation in order to reduce leakage current
below 3.5mA.
CAUTION! When replacing the batteries, use the same number and
type of batteries.
CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid,
6-cell battery.
CAUTION! Electric shock hazard. When UPS is disconnected from the
mains source, hazardous voltage may still be available through the
batteries. Disconnect all battery connectors from battery terminals prior
to doing any maintenance or service works.
CAUTION! Servicing of batteries should be performed or supervised by
personnel knowledgeable of batteries and the required precautions.
Keep unauthorized personnel away from batteries.
CAUTION! Do not dispose of batteries in a fire. The battery may explode.
Do not open or mutilate the battery or batteries. Released electrolyte is
harmful to the skin and eyes.
CAUTION! Unplug the UPS prior to cleaning and do not use liquid or
spray detergent.
CAUTION! A battery can present a risk of electric shock and high short
circuit current. The following precaution should be observed before
replacing batteries:
1. Remove watches, rings, or other metal objects.
2. Use tools with insulated handles.
3. Wear rubber gloves and boots.
4. Do not lay tools or metal parts on top of batteries.
5. Disconnect charging source prior to connecting or
disconnecting batteries terminal.
UPS
Quick-start
Guide
1 x Power Cable
As Output Cable:As Input Cable:
TO WALL
SOCKET TO DESKTOPPC Power Button
20CM
CLEARANCE

LIEBERT® PSA itON-SOHO 650/850/1000VA, 230V
User Manual
2Liebert® PSA itON-SOHO User Manual (R1/071621)
UPS CONTROLS AND CONNECTIONS
UPS STATUS, ALARM CONDITIONS AND ALERTS
Condition LED Color Solid/Flashing Audible Alarm
Normal Mode LED 1 Green Solid (none)
Battery Mode LED 2 Yellow Flashes Every 10 seconds
Battery Low LED 2 / LED 3 Yellow/Red Flashes/Solid Every 1 second
Overload at Normal Mode LED 1 Green Solid Every 0.5 second
Overload at Battery Mode LED 2 / LED 3 Yellow/Red Flashes/Solid UPS shuts down immediately
Fault LED 3 Red Solid Continuous until UPS shuts down
TROUBLESHOOTING
If the UPS malfunctions during operation, check the following chart for proper adjustment. For further assistance, pleas contact your
local Vertiv representative
Problem Possible Causes Solutions
Utility is normal, but LED 1 is not illuminated
• Battery capacity may be low.
• The UPS battery reached end of life.
• The UPS may not be turned on.
• Recharge the UPS at least 6 hours
• Replace the battery with the same type of battery.
• Press the ON/OFF button to turn on the UPS.
Alarm buzzer beeps continuously although
utility power is normal
• The UPS may be overloaded • Disconnect some equipment from the UPS
UPS does not provide expected backup time
• The UPS may be overloaded.
• Battery voltage may be low.
• The UPS battery reached end of life.
• Disconnect some equipment from the UPS
• Recharge the UPS at least 6 hours
• Replace the battery with the same type of battery.
Utility is normal, but LED 1 flashes • The power cord may not be connected properly • Connect the power cord securely into a wall outlet

Vertiv.com
© 2021 Vertiv Group Corp. All rights reserved. Vertiv™ and the Vertiv logo are trademarks or registered trademarks of Vertiv Group Corp. While every precaution has been taken to ensure accuracy
and completeness herein, Vertiv Group Corp. assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions.
Specifications are subject to change without notice.
3Liebert® PSA itON-SOHO User Manual (R1/071621)
LIEBERT® PSA itON-SOHO 650/850/1000VA, 230V
User Manual
Technical Specifications
Model Number PSA650-SOHO PSA850-SOHO PSA1000-SOHO
Capacity (VA/W) 650VA/390W 850VA/510W 1000VA/600W
Input
Voltage range 162 – 290VAC, single-phase
Frequency range 50Hz/60Hz automatic identification
Output
Voltage tolerance (Batt. Mode) Simulated sine wave at nominal voltage ±10%
Frequency range (Batt. Mode) 50Hz/60Hz automatic identification
Transfer time Typical 2–6 ms, 10ms max.
Battery
Battery type & Number 12V/7Ah × 1 12V/9AH × 1
Typical recharge time 4 hours to 90% 6-8 hours recover to 90% capacity (About 1A charging current at Normal Mode)
Configuration
Battery 1×2.0kg, 7Ah 1×2.4kg, 9Ah 1×2.7kg, 9Ah
Sockets 3×Universal 6×Universal
USB Charger *1 *1 *0
Runtime: Time (in minutes)
Load%
25% 15m 16m 18m
50% 4m 3m 4m
System Features
Indicators AC Mode: Solid green led lighting; Battery Mode: Solid yellow led flash; Fault Solid: Red led lighting
Protection Discharge, Overload and overcharge protection
Alarm 1.) Battery Mode: Sounding every 10 seconds; 2.) Low battery: Sounding every 1 second;
3.) Overload: Sounding every 0.5 second; 4.) Fault: Continuously sounding
Operating temperature 0 ~ 40°C
Humidity range 0 ~ 90% (non-condensing) 0 ~ 95% (non-condensing)
Noise level Less than 40dB (1 meter from surface)
Fuse Protection YES
USB Charging slot YES (5.0V/1.0A) NO
Physical
Dimension D × W × H (mm) 85 × 272 × 201 85 × 272 × 201 87 × 346 × 208
Gross weight (kg) 5 kg 5.4 kg 6.6 kg
Net weight (kg) 4.4 kg 4.9 kg 6.0 kg