Vertiv Liebert GXT5-500LVRT2UXL User manual

LIEBERT® GXT5™ UPS
120‑V500–3,000VA
Quick Installation Guide
590-1932-501A/SL-70307_REV0 1
I M P O R TAN T: Before installing,
connecting to supply or operating
your Liebert GXT5 UPS, please
review the Safety and Regulatory
Statements sheet. For detailed
installation, operating, maintenance
and troubleshooting info
rmation refer to the GXT5 User
Guide for your model available at
www.VertivCo.com.
INSTALLATION
1. Inspecting the UPS
Inspect the UPS for any signs of
obvious damage. If damage is
visible, do not proceed and call
our warranty support line for
assistance at 1-800-222-5877
menu option 3, or email at
microups.[email protected].
2. Choosing a location
Install the UPS in a temperature-
controlled environment that is
free of corrosive and conductive
contaminants. Avoid locations
near heat or water sources and
exposed to direct sunlight.
For proper ventilation, leave four
inches clearance on all sides of
the UPS.
The input outlet should be
nearby and easily accessible.
3. Installing the UPS
The UPS and optional External
Battery Cabinets may be
installed in either a tower or rack
conguration. For tower
installation, assemble and attach
the tower support stands. For
rack installation, attach the
brackets to the UPS, install the
rail kit in the rack if needed, and
install the UPS in the rack.
NOTE: This UPS is not for use in a
computer room as dened in the
standard for the protection of
electronic computer/data
processing equipment of ANSI/
NFPA 75.
MODEL DESIGN CONFIGURATIONS
GXT5‑500/750/1000/1500LVRT2UXL
GXT5‑2000LVRT2UXL
GXT5‑3000LVRT2UXL
1 4 7 5 6
2 9
310 8
1 4
7
5 6
2 9
310
8
11
1 4
7
5 6
2 9
310
8
11
12
GXT5 UPS
#Description #Description
1Liebert® IntelliSlot™ port 7Input circuit breaker
2USB port 8Input-power plug and cable
3RS-485 port 9RS-232 port
4External-battery connector 10 Terminal-block
communication connectors
5Non-programmable
output receptacles 11 Output-power plug and cable
6Programmable
output receptacles 12 Output circuit breaker

LIEBERT® GXT5™ UPS 120-V 500 – 3,000 VA
Quick Installation Guide
2 590-1932-501A/SL-70307_REV0
CONNECTIONS
4. Connecting External
Battery Cabinet
(Optional)
External battery cabinets
(EBC) provide longer battery
run-time for connected
devices. Refer to GXT5 User
Guide, to select the appropriate
model and quantity for your
GXT5 model and applications.
• Verify that the EBC breaker
is in the “O” position.
• Connect one end of the
supplied EBC cable to the
UPS and one end to the
battery cabinet. If
connecting more than one
external battery, connect
one end of the external
battery cable to the second
connector on the battery
cabinet, then connect the
other end to the next
battery cabinet.
5. Connecting the UPS
to Receptacle
The UPS is cord and plug
connected using a L6-30P
input plug. Perform all wiring in
accordance to all local and
national electrical codes.
The
UPS is equipped with
output receptacles. Connect
the equipment to be protected
to the output receptacles.
NOTE: Allow the batteries to
charge at-least 8 hours before rst
start-up to ensure adequate
back-up time. The batteries charge
when the UPS is connected to AC
input regardles of the o/on status
of the UPS.
POWERING THE UPS
NOTE: Do not start the UPS until
after the installation has been
nished, the system is
commissioned by an authorized
engineer, and the external input
circuit breakers have been closed.
1. If an optional POD is installed,
make sure the bypass switch is
in “UPS” position.
2. Make sure the breaker
supplying power to the UPS is
closed, and close the input
breaker on the rear of the UPS.
EBC terminal
GXT5TM UPS to External Battery Cabinet Connections
GXT5‑3000LVRT2UXL
Shown
Single/First EBC
Second EBC
WIRING
Model Recommended external over-current protection
(Maximum)
GXT5-500LVRT2UXL
GXT5-750LVRT2UXL
GXT5-1000LVRT2UXL
12 A
GXT5-1500LVRT2UXL 15 A
GXT5-2000LVRT2UXL 20 A
GXT5-3000LVRT2UXL 30 A

LIEBERT® GXT5™ UPS 120-V 500 – 3,000 VA
Quick Installation Guide
590-1932-501A/SL-70307_REV0 3
3. If necessary, use the LCD
display or a connected
computer to make any required
settings. (Refer to the User
Guide for conguration set up.)
4. Close all output breakers on the
rear of the UPS (or in an
external panel board, if used).
5. If external battery cabinets are
included, close the breakers on
the rear of each cabinet.
6. Power-on the UPS using the
Operation and Display Panel
(see the illustration to the right)
by pressing and holding the
power button until the
conrmation dialog appears.
Use the Up/Down arrows to
select “YES”, then press Enter.
NOTE: During operation, the UPS
may sound an alarm as the output
receptacles are powered. You may
press the Esc button for 2 seconds
to silence the audible alarm.
Display
screen
Power
Operation and Display Panel
Run
Alarm
Enter
Down
Up
Escape

To contact Vertiv Technical Support: visit www.VertivCo.com
© 2018 Vertiv Co. All rights reserved. Vertiv and the Vertiv logo are trademarks or registered trademarks of Vertiv Co. All other names and logos referred to are trade names,
trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no
responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specications are subject to change without notice.
4 590-1932-501A/SL-70307_REV0