VES XT+ User manual

XT+ Releasing Control Unit
Installation Manual
Version 1.00 |December 2018 |MAN-1252VES

VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 2

CONTENTS
Contents 3
Compliance Information 7
Underwriters Laboratories (UL) 7
NFPA 7
FM Global Technologies LLC (FM APPROVALS) 8
Introduction 9
Technical Support 9
Return Material Authorization (RMA) 9
Warranty Service 10
Advanced Replacements 10
Overview 11
Fascia 11
Buttons 12
LEDStatus Indicators 13
Keyswitches 13
Internal Indicators and Switches 13
Terminals 14
Top 14
Bottom 14
Power Supply 14
Features 15
Batteries 15
Installation 17
Contents
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 3

Preparing for Installation 18
Mounting the XT+ Unit 18
Removing Cabinet Components 19
Replacing Cabinet Components 19
Installing the Power Supply 19
DIPSwitches 21
5.25 Amp Power Supply 21
Status Indicators 22
Connecting Standby Batteries 23
Connecting Field Wiring 24
Networking Multiple XT+Modules 25
24V Power 26
Aux 24V 26
Trouble 26
1st Stage 27
2nd Stage 27
3rd Stage (Released) 27
Supv. / Abort 27
Extract 27
Notification Appliances 28
3rd Stage Alarm 28
2nd Stage Alarm 28
Exting. 1 (Main) and Exting. 2 (Reserve) 28
Bottom Terminals 29
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 4
Contents

CIESerial 30
Status Serial / Status Pow. 30
Access Levels 31
Standby Mode 31
Access Level 2 31
Access Level 3 33
Set the Extinguishant Output Calibration 33
System Startup 35
Setting the Address 35
CIESerial Bus Termination 35
Testing the Installation 35
Testing the Power Supply 35
Lamp, Display, and Buzzer Test 36
Communication Between Elite RS and XT+ 36
Testing Field-Installed Devices 36
Configuration 36
Times Tab 37
Disablements Tab 38
Settings Tab 39
NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION, AND OTHER
INVOLVED PARTIESULCompliance Limitations 41
Appendix A: Specifications 42
Terminal Electrical Ratings 43
Appendix B: Maintenance and Repair 44
Contents
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 5

Batteries 44
Replacing Battery Leads 44
Replacing Standby Batteries 44
Removing the Standby Batteries 44
Installing the Standby Batteries 45
Fuses 45
Battery Lead Fuse on 5.25A Power Supply 45
Replacing the Power Supply Fuse 45
Removing the Power Supply Fuse 45
Installing the Replacement Power Supply Fuse 46
Troubleshooting 46
Appendix C: Equipment List 48
Model Numbers 48
Replacement Parts 49
Accessories 50
Compatible Releasing Devices 51
Special Releasing Accessories 52
Index 53
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 6
Contents

COMPLIANCE INFORMATION
Underwriters Laboratories (UL)
Fire Alarm Equipment
VESFireDetection Systems
The XT+ Releasing Control Unit is suitable as follows:
nTypes of signaling services are automatic fire alarm and manual fire alarm
nClass B for Notification Appliance Circuits
nProtected Premises Unit (PPU) for Local Service, Remote Station Service, Center Station Service, Pro-
prietary Service, Auxiliary Service when used with the Elite RS FACP.
NFPA
Install this product in accordance with NFPA 13, NFPA 72, NFPA70, and NEC 70 and all local codes.
Install SLC detectors with spacing as specified in section NFPA 72. Units employing "multiple detector
operation" shall include guidelines for installing of a minimum of two detectors in each protected space and to
reduce the detector installation spacing to 0.7 times the linear spacing in accordance with National Fire Alarm
Code, NFPA 72.
All field wiring should be installed using fire rated cables according to the NFPA 72. Riser conductors shall be
installed in accordance with the survivability from attack by fire requirements in National Fire Alarm Code, NFPA
72, Section 12.3. Riser conductors shall employ either a 2 hour rated cable system, or meet requirements
approved by the AHJ.
This product, when used with XT+ Releasing modules K1711-xx & K1712-xx, satisfies releasing operation
under:
• Carbon dioxide extinguishing systems, NFPA 12
• Halon 1301 fire extinguishing systems, NFPA 12A
• Sprinkler systems, NFPA 13
• Water spray fixed systems for fire protection, NFPA 15
• Foam-water sprinkler and foam-water spray systems, NFPA 16
Compliance Information
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 7

• Dry chemical extinguishing systems, NFPA 17
• Wet chemical extinguishing systems, NFPA 17A
• Water mist, NFPA 750
• Clean agent fire extinguishing systems, NFPA 2001
• Fixed Aerosol fire extinguishing systems, NFPA 2010
FM Global Technologies LLC (FM APPROVALS)
VESFireDetection Systems
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 8
Compliance Information

INTRODUCTION
Technical Support
For technical support, contact VES at 800.274.9514 or e-mail [e-mail]. VES technical
support is available Monday through Friday, 9:00 AM to 6:00 PM, EST.
Prior to contacting technical support, have the following information available:
nProduct part number
nPurchase order or order number
nProduct serial number
nCurrent function of the product
nExpected function of the product
nInstallation of the product
Return Material Authorization (RMA)
Contact Technical Support to obtain an RMAfor any product to be returned. Returns will not be accepted
without an accompanying RMA number. An RMA number is assigned when:
lTech Support acknowledges a possible product failure.
lA product was damaged during shipping
lAn incorrect product was shipped
lAn order was placed using an incorrect part number *
lAn order was placed using an incorrect part quantity *
lAn order is no longer required *
* Restocking fees may apply.
All returned products are tested to confirm operating failures experienced in the field. If the product is found to be
functional, contractors must absorb expenses for return shipping, as well as the cost and shipping of the
advanced replacement product.
Prominently display the RMA number on all packages sent for return. Ship all return products to:
Attention: RMA # _____________
Introduction
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 9

620 Allendale Road, Suite 175
King of Prussia, PA 19406
Warranty Service
Technical Support can replace or repair a defective product when the original purchase is within the warranty
period defined in the sales contract. Check your contract for more information, or contact your sales
representative about your specific warranty period.
Advanced Replacements
Products that fail to operate in the field can be replaced quickly using the advanced replacement process. The
advanced replacement process is available to all contractors who maintain an acceptable line of credit.
Initiate the advanced replacement process by requesting an RMA number from a Tech Support representative.
Advanced replacements can be shipped to your location when the product is covered under warranty and when
a replacement product is in stock.
lAdvanced replacements can be expedited at the request of the contractor. Shipping costs associated with
this process are the responsibility of the contractor.
lProducts returned using the advanced replacement process must be received within 30 days of the RMA
issue date.
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 10
Introduction

OVERVIEW
The XT+ Releasing Control Unit is a microprocessor-controlled releasing control unit that will communicate with
a master fire alarm control panel via a two-wire serial bus. Each unit may contain one or two independent
XT+modules, as shown. Up to 15 modules can be connected to an Elite RSpanel, model number VF0810-xx or
VF0820-xx, firmware V07.02.005A (for Apollo) or greater or V07.02.005H (for Hochiki) or greater.
As shown in the image, the entire cabinet and everything contained within is referred to as a "unit". The individual
releasing modules and power supply are referred to as "modules".
Fascia
This section describes the featuresof the XT+ that are located on the fascia.
Overview
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 11

Buttons
Label Description
(-) and (+) Press (-) to move back through the menus and (+) to move forward through the menus.
Exit Press Exit to return to the Main Menu.
Silence Buzzer Mutes the internal buzzer of the XT+module. No NACoutputs are silenced. If the unit contains two mod-
ules, each module must be silenced individually.
Reset
Reset clears latching inputs on the XT+ module. The Extinguishant Release button and Man.Rel input
terminal are the only latching inputs. This button does not reset the master control or latching inputs of
other modules.
Enter Press Enter to enable the menu selection when in AccessLevel 2 or 3.
Extinguishant Release Initiates the releasing process, which can happen immediately or after 30 seconds, depending on the
configuration. This button shall not take the place of any NFPA required manual release device(s).
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 12
Overview

LEDStatus Indicators
Label LEDColor Description
EXTERNAL
Power On Green The XT+ is powered on.
System Trouble Yellow An internal hardware trouble exists.
Abort Activated Yellow The Abort Input is active.
Release Imminent Red One of the contributing devices within a zone has activated.
Reserve Cylinders Yellow The reserve (backup) cylinder is currently the active cylinder.
Trouble Yellow
The Trouble LEDilluminates in the event of any trouble condition on the
XT+ module(s) or disconnection of the serial bus between Elite RS panel
and XT+ module(s).
Disablement Yellow
The Disablement LEDilluminates when options of the LCD menu have
been used to disable specific devices and when the disablement input is
active.
Supervisory Yellow A supervisory point has been activated. Status is provided on the LCD dis-
play and the buzzer sounds continuously.
Extinguishant Released Red The extinguishant is actively being released.
Manual Only Yellow The XT+ is manual mode. Extinguishant will not automatically be
released.
INTERNAL
W/Dog Tell Tale Yellow
Indicates that the processor has failed to correctly execute code and has
been restarted by the watchdog circuit. The watchdog reset switch must
be pressed to clear the Watchdog trouble condition. Press the W/dog
Reset button. If the system does not return to normal, the module is prob-
ably damaged and needs to be replaced.
System Fuse Yellow Indicates that the main fuse has been overloaded and the module has
shut down. Review all loads and reconnect one at a time.
Man. Release Yellow
Indicates that a manual release has been initiated. This indication can
only be cleared by power cycling the module or pressing the Proc. Reset
button.
Keyswitches
Label Description
Enable Access
Insert the key in the lock and turn it to the right to obtain Access Level 2. XT+ releasing modules will ignore
Enable Access commands from the Elite RS panel and will enter access level 2 only when their own Enable
Access switch is operated.
Mode Select Insert the key in the lock and turn it to the right to put the module into Manual mode.
Internal Indicators and Switches
Overview
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 13

These indicators and switches are only accessible when the unit is unlocked by qualified service personnel.
Label Description
Term. Exting. Terminates the flow of extinguishant caused by a releasing event and resets the operation of the XT+.
Proc. Reset Resets the XT+ processor.
W/dog Reset Clears the watchdog event caused when the unit failed to carry out an operation.
Address Each module must be allocated an address between 1 and 15 using the binary coded DIP switch.
Write Enable
When this switch is on, the configuration will be write-protected.
When this switch is off AND the Enable Access keyswitch is on, the module will be at access level 3; if not, the
module will indicate a configuration ROM write-protect trouble.
Terminals
For detailed descriptions and wiring information, refer to the Installation section.
Top
Bottom
Power Supply
The XT+ uses a 5.25 Amp power supply, capable of charging batteries with capacities ranging from 7 to 60 Ah
and providing an output voltage of 24V and accepting input voltages of 120 VAC or 240 VAC. A jumper
connection for the 5.25 Amp power supply is set at the factory according to input voltage requirements of the
customer, either 120VAC or 240 VAC.
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 14
Overview

Features
Features of the power supplies include:
Features Description
Deep Discharge
Prevention
Prevents deep-discharge of the standby batteries by disconnecting the load when the standby bat-
tery-voltage drops below 19 +/- 1V DC. A deep-discharge can cause permanent damage to standby
batteries. Preventing this condition allows standby batteries to recharge for continued operation
after extended power outages.
Battery Backup Provides battery power to the load when the AC input of the power supply falls below the rated
level. The voltage at the load remains within the specified range during these switching-transitions.
Battery Boost Boosts standby battery voltage to maintain a constant 22 VDC when the voltage drops below the 22
VDC level.
Short-Circuit Protection Provides a shut down on the load side of the power supply when the load-current exceeds the max-
imum level.
Automatic Retry Restores output to the load when operating conditions return to nominal levels. This feature
restores voltage levels at the load following conditions such as over-current and AC restore.
Battery Impedance Provides a warning when the impedance of the battery reaches a level that could prevent proper
system operation.
Battery Supervision Battery presence and low battery voltage supervision
Earth Fault Detection Earth Fault Detection
General Trouble Relay All troubles are reported over the common trouble contacts.
Batteries
Standby Battery Type Two 12 VDC, valve-regulated lead acid
Standby Battery Charging Two standby batteries wired in series
Maximum Amp Hour Capacity 60 AH maximum
Charge Current 1.25 A Max
Output Current 4 A Max
Maximum Alarm Current 4A
Normal Standby Load during AC Fail
XT+ 1 Area Releasing Control Unit: 140mA
XT+ 2 Area Releasing Control Unit: 230mA
XT+ 2 Area Releasing Control Unit w/ Status unit & Ancillary board for each Area: 372 mA
A 12Ah battery can support a full alarm load (4A) for 7 minutes following 24hr standby
with a max standby load of 379mA.
Standby Operating Time 24 Hours
Battery Charge Voltage 27.6 VDC
Recommended battery size is 12 Ah for a typical configuration. Required battery size is mainly dependent on
standby current. To determine the most appropriate battery size, use the battery calculator in LE2.
Overview
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 15

If your required battery capacity exceeds the space available in the cabinet, an appropriately-sized auxiliary UL
listed battery cabinet suitable for fire alarm service will be required. If needed, install that cabinet (wired close-
nippled) adjacent to the unit to minimize battery lead length.
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 16
Overview

INSTALLATION
This section provides instructions for connecting cables, mounting, and testing the XT+ Releasing Control Unit
for installation. The following is a general checklist for the installation of the unit. Detailed instructions are
provided for each step.
IMPORTANT! The XT+ Releasing Control Unit installation must be performed by qualified service personnel.
Maintain extreme care when anchoring the cabinet to the premises wall. Electronic components within the unit are
vulnerable to physical damage from severe shock and vibration. Remove the cabinet door and fascia from the cabinet
when installations cannot guarantee vigilant care during cabinet anchoring.
Task
qObtain required mounting hardware, tools, and batteries.
qDisconnect ground cables and all pre-installed wiring.
NOTE It is recommended that a photo is taken of the factory wiring for ease of reinstallation.
qOpen and remove the door and fascia from the cabinet.
qDisconnect and remove the power supply from the cabinet.
qAnchor the empty cabinet to the premises wall.
qThread the cabling into the cabinet.
qReinstall the power supply and fascia.
qReconnect all factory pre-installed wiring.
qConnect all field wiring.
qReinstall the door and reconnect ground cables.
qPlace standby batteries in the base of the unit and connect them to the power supply.
qApply power to the unit from the AC source.
qConfigure the unit using Loop Explorer 2.
qTest the installation.
Installation
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 17

Preparing for Installation
1. Refer to the checklist provided above before beginning the installation process. For detailed information,
refer to the appropriate, referenced section in this document.
2. Select a suitable operation environment. The site should be clean, dry, and not subject to shock or vibra-
tion. Ensure that the environment is free from wire ends, knockout tabs, and other debris.
3. Familiarize yourself with the unit and components.
Item Description
Power Supply The XT+will have a 5.25 A power supply.
Ground Cable(s) Ground cabling is green and yellow, insulated wire containing connecting lugs. Ground cabling
provides common electrical grounds of the cabinet to the door.
4. The following items are not included, but may be required for the installation:
lTwo 12 VDC VRLA (Valve-Regulated Lead Acid) Standby Batteries - Required
lMounting Hardware - Mounting hardware that secures the cabinet to the wall is not provided. Screws
should be either a #10 or #12.
lA Ground Strap is required for handling circuit boards.
lVarious Diodes and Resistors: S2027 - 6.8k Ohm Resistor, S2028 - 10k Ohm Resistor, S2029 - EOL
Diode, S2051 - 470 Ohm Trigger Resistor
Mounting the XT+ Unit
IMPORTANT! Electronic components within the unit are vulnerable to damage from electrostatic discharge.
Ground straps must be worn by installers before handling circuit boards to prevent damage from electrostatic
discharge.
Mount the cabinet box on a flat, dry surface. Use the cabinet box as a template and mark the position of the
mounting holes while ensuring that the wall is flat at the chosen location. The unit must be mounted in an
accessible location. It must not be mounted in another enclosure or near sources of excessive heat. The unit is
intended for indoor, dry use only. Use knockout tabs of the cabinet box to route external cabling into the unit.
IMPORTANT! Drilling additional holes in the cabinet will void the product warranty.
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 18
Installation

Removing Cabinet Components
Remove the door, fascia, and power supply before mounting the cabinet box. To remove these components:
1. Disconnect all wires and cables between the door/fascia and the cabinet.
2. Remove the hinge pins of the fascia and then remove it from the cabinet box. Return the hinge pins to the
hinges of the cabinet box for safekeeping.
3. Remove the hinge pins of the door. Return the two hinge pins to the hinges of the cabinet box for safe-
keeping.
4. Disconnect the power supply and remove it from the cabinet.
5. Mark hole locations on the wall for mounting the empty cabinet.
6. Drill holes and anchor the empty cabinet box to the wall using appropriate mounting hardware to secure
it.
7. Remove the necessary number of knockout tabs from the cabinet box and feed external cabling into the
unit.
WARNING! Separate high and low voltage wiring in the enclosure with a minimum gap of 0.25". Do not route low
voltage cabling through the same conduit as AClines. ACpower lines should be threaded through a dedicated
conduit.
Replacing Cabinet Components
1. Replace the power supply.
2. Replace the door and fascia.
3. Reconnect the cabling.
4. Install the standby batteries.
Installing the Power Supply
The XT+ is equipped with a 5.25 Amp power supply. Set DIP switches on the power supply before completing
the installation process. Refer to DIP Switch Settings. The power supply settings must be performed to
establish the optimal charge current of the standby batteries. These power supplies can be set to operate at
Installation
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 19

inputs of 120 VAC or 240 VAC. For more information about the power supplies and their functions, see
Section 1: Power Supplies.
The power supply contains a jumper setting for changing from 120 VAC to 240 VAC. Check the jumper setting
prior to wiring and operating the 5.25 Amp Power Supply.
WARNING! Remove jumper J1 before operating the unit at 240 VAC. Failure to remove jumper J1 prior to
operation will cause permanent damage to the power supply.
Confirm that the 5.25 Amp Power Supply is set for 240 VAC before operating. Permanent damage of the
power supply will result if the 120 VAC jumper setting exists while operating the power supply at 240 VAC.
High voltage is present on jumper pins. Remove ACpower before changing jumper setting.
VESFireDetection Systems
XT+ Releasing Control Unit Installation Manual
Version 1.00 |December 2018 |MAN-1252VES
Page 20
Installation