Vestil D-HEAD-1 User manual

1
04-08
A company dedicated to solving ergonomic and material
handling problems since 1955.
OWNER'S
MANUAL
DRUM DEHEADER
Model D-HEAD-1
Vestil Manufacturing Corporation
2999 North Wayne St., P.O. Box 507
Angola, IN 46703 USA
Ph 260-665-7586 • Fax: [phone]
www.vestil.com • [email protected]
OPERATING INSTRUCTIONS
MODEL D-HEAD-1 DRUM DEHEADER
Insure that all employees understand and follow the
following instructions.
The drum deheader works much like a kitchen can opener
on a larger scale. The Vestil Drum Deheader Model
D-HEAD-1 utilizes pressure created by a vise-grip style
clamp to force rolling cutting wheels into the drum lid. The
finished opening has a very smooth rolled edge making it
safer to handle due to no sharp edges to cut the handler.
The opener uses replaceable cutting blades that can be
easily replaced when cutting capabilities are decreased.
The opener can be used on a variety of styles of drums
with permanently sealed lids. There may be some
instances however where bung nuts may come into contact
with the cutting head. Many times the deheader can be
manipulated around these obstacles with a little care.
However, in few instances, there may be special made
drums that this opener may not be able to work with.
The first step in opening any drum is to make sure that the
contents are completely emptied from the drum before
beginning. If working with hazardous materials, be sure the
proper gear is worn and all necessary precautions are
taken to avoid accidents. The drum deheader is not spark
resistant and can possibly created sparks if struck against
another object so use on highly flammable materials or
explosives is not recommended.
Secure the drum opener to the top lip of the drum with the
1/2" drive socket up and the cutting wheel against the
inside of the lip. The cutting wheel should be as low as
possible on the drum lid to allow for easier cutting. The
two drive gears should rest against the outer ledge of the
drum ring. Clamp the drum deheader down onto the drum
ring when location of the cutting wheel and gear is
achieved. Adjust the clamping force much like a "vise
grip" style wrench. Be careful not to clamp too much
pressure as the cutting wheel is hardened and can break
when excessive force is applied. Try to adjust the wrench
so it takes 20 - 30 lbs. to close the wrench.
Place a 1/2" drive ratchet into the 1/2" "socket like"
receptacle in the top of the wrench. Rotate the ratchet
clockwise and hold the drum wrench 90° to the drum side
to maintain force on the cutting wheel. After completing
one rotation around the drum, readjust the clamping force
again to 20 - 30 lbs. This may be required several times
dependent on the thickness of the drum. When making
consecutive rotations around the drum, be sure to stay in
the same cutting path as the previous cut. After cutting
through the drum lid, take a hammer to tap the lid down
into the drum for easier removal.
As with many hand tools, using the drum wrench several
times will help the operator perfect their style and will
become easier for them to operate. Pneumatic impact
wrenches or air ratchets can also be used with this
wrench to speed the process, but caution should be
used. Air tools are extremely powerful and can injure an
operator when an obstruction is encountered.
To replace blades, simply remove the screw in the center
of the cutting wheel and slide the wheel out from the
side. Place the new cutting wheel with the offset to the
top and reinstall the screw. Tighten the screw down until
the cutting wheel does not rotate and back the screw out
slightly to allow rotation again.
PRESSURE
ADJUSTMENT KNOB
CUTTING WHEEL
1/2" DRIVE SOCKET

Copyright 2016 Vestil Manufacturing Corp. Page 2
LIMITED WARRANTY
Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship
during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is
covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service.
Who may request service?
Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an
authorized distributor AND Vestil has been fully paid.
What is an “original part”?
An original part is a part used to make the product as shipped to the warrantee.
What is a “proper request”?
A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the
shipping date; AND 2) a written request for warranty service including your name and phone number. Send requests
by any of the following methods:
Mail Fax Email
Vestil Manufacturing Corporation [phone] s[email protected]
2999 North Wayne Street, PO Box 507 Phone
Angola, IN 46703 [phone]
In the written request, list the parts believed to be defective and include the address where replacements should be
delivered.
What is covered under the warranty?
After Vestil receives your request for warranty service, an authorized representative will contact you to determine
whether your claim is covered by the warranty. Before providing warranty service, Vestil may require you to send the
entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the
following original dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders. It also
covers defects in original parts that wear under normal usage conditions (“wearing parts”): bearings, hoses, wheels,
seals, brushes, batteries, and the battery charger.
How long is the warranty period?
The warranty period for original components is 15 days. The warranty period begins on the date when Vestil ships the
product to the warrantee. If the product was purchased from an authorized distributor, the period begins when the
distributor ships the product. Vestil may extend the warranty period for products shipped from authorized distributors
by up to 30 days to account for shipping time.
If a defective part is covered by the warranty, what will Vestil do to correct the problem?
Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact
you to discuss your claim.
What is not covered by the warranty?
1. Labor;
2. Freight;
3. Occurrence of any of the following, which automatically voids the warranty:
 Product misuse;
 Negligent operation or repair;
 Corrosion or use in corrosive environments;
 Inadequate or improper maintenance;
 Damage sustained during shipping;
 Collisions or other incidental contacts causing damage to the product;
 Unauthorized modifications: DO NOT modify the product IN ANY WAY without first receiving written
authorization from Vestil. Modification(s) might make the product unsafe to use or might cause excessive
and/or abnormal wear.
Do any other warranties apply to the product?
Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent
allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty.