VEVOR RA250200 User manual

Technical Support and E-Warranty Certificate www.vevor.com/support
RETRACTABLE PATIO AWNING
USER MANUAL
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and doses not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.

1
RA250200
RA300250
RA350300
RA400250
Have product questions? Need technical support? Please feel free to
contact us:
[e-mail]
NEED HELP? CONTACT US!
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our
user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again if
there are any technology or software updates on our product.
RETRACTABLE PATIO
AWNING

2
NOTICE:
Protect from severe weather conditions.
Wipe clean with a moist cloth and mild detergent.
Do not use abrasive materials or cleaners.
Carelessness causes fire-keep open flames away from covers.
2 people are recommended for mounting this product.
Please retain these instructions for future reference.
SPECIFICATIONS
Model
RA250200
Product Size
8×7ft
Color
khaki
Model
RA300250
Product Size
10×8ft
Color
khaki
Model
RA350300
Product Size
12×10ft
Color
khaki
Model
RA400250
Product Size
13×8ft
Color
khaki

3
PARTS LIST

4
Please prepare the following tools before installation (not included with the product).
Power drill
Tape
Wrench
Rubber Hammer
WARNING
Please read the instruction manual carefully before using it.
Please assemble this product strictly according to the instructions.
Please double-check that all parts of the package contents are intact.
The mechanical arm will pop out immediately after the safety casing is removed, which will
cause damage to the assembler. Please do not remove the safety casing.

5
Assembly steps
Roller assemble: Insert the roller connector (A-2) into the right roller (A-3) and secure it
with the screw (S). Connect the left pulley (A-1) with the pulley connector (A-2) and fix
it with the screw (S). Now you have a full-length roller.

6
Front Pole Assemble: Insert Front Pole Connector (D-2) into Right Front Pole (D-3) and
secure it with screw (S). Connect the left front rod (D-1) to the connector (D-2) and secure it
with the screw (S). You now have a full-length front bar.

7
Unfold the awning fabric. You will have a large piece of fabric (C) and a valance with a
scalloped edge. You will also have three strips, two thick and one thinner. Insert the thick
and thin strips into both ends of the large piece of fabric.

8
Put the end of the fabric with the thin strip in the groove of the roller. Then put the end with
the thick strip in the cut of the front bar and put the end of the flounce with the thick strip in
the other cut of it.

9
Slide the blocker (l) and arm-bar connector (K) into the passage / slot in the wedge-shaped
front bar, Cut off the excess part of the long strip. Then pull the left and right plastic
covers(H) on each end of the rod, and then screw in the screw (R) on the plastic cover to
secure the cover (H) and strip (T) in place. Insert the rotator (V, W) into the roller (A).

10

11
Slightly loosen the nut so that the parts can be moved left and right for further assembly.
Assembly of the entire awning: Insert the square shaft with fabric into the square hole of the
gear unit and connect it to the round shaft on the right-hand side with a hammer.
Loosen the nut slightly so that the parts can be moved left and right for further assembly.
Assembly of whole awning: Insert the square shaft in the roller with fabric into the square
hole of the gearbox, and link it with a round shaft on the right side using a hammer.
Pay attention to the winding direction of the cloth！

12
The next step is to unlock the security straps. We need to firmly grip the limb of
the movement arm bar with our hands to prevent the limb of the movement
arm bar from injuring people if it pops out of the safety band.

13

14
Please prepare the following tools before installation (not included with the product).
Installation Procedure:
1. Measure the distance along the wall where it can be placed. Drill holes for wall brackets
on the wall according to the installation distances and height of the wall brackets. The
diameter and depth of the hole must be the same as the expansion bolts.
The holes of each group must be on the
same line in transversal direction and
vertical direction.
(Note: It is recommended to draw lines
on the wall first to ensure the precise
position and size of the holes)
2. Hammer all the expansion bolts into the holes. Then take down the nuts and washer.
(Note: ①The expansion bolts must be hammered into the wall completely.
②The bolts must be stuck out of the wall so that the wall brackets can be installed on it.
③The nut and washer might be separated from the bolt during the process of transportation.
Please put them back into their original positions before hammering them into the wall.)
3. Take down the original bolts of the wall brackets, as shown in the figure. Use expansion
bolts to fix the wall brackets on the wall. Do not tighten completely. Leave wall brackets to
stay on the wall with a little movement.

15
Installation distance between wall brackets
Awning < 3m
Only 2 wall brackets for each end of the torsion bars.
Awning 3.5m ~ 4.5m
2 wall brackets at each end of the torsion bar, a middle
bracket in between the distance of 2 arm shoulders (arm
brackets refer to steps of assembly 6)
Awning > 5m
2 wall brackets at each end of the torsion bar, 2 middle
brackets divide into equal lengths in between the distance
of 2 arm shoulders at each end of the torsion bars.(Steps of
assembly 6)
4. As shown in the figure, we recommend making the awning surface to form an angle of
about 80 degrees with the wall when it is open.
A) The height of the front bar you desire
L) The length of the arm stretches out
C) The height of wall brackets
You can follow this formula: C= A + 0.17*L

16
5. Install the awning on the wall brackets according to "Installation distances between
wall brackets" above, put the original bolts on the wall brackets and tighten them. Finally,
fasten all expansion bolts.
CAUTION: Proper location of the brackets is the most important aspect of the awning
installation. It is critical that you fasten all the mounting brackets to studs, joists,
headers or other major structural components.
WARNING: Failure to securely fasten all the brackets to the wall could result in the
collapse of the awning and cause personal injury or death.
6. Instruction for front side leveling
①Loosen the locking nuts.
②Turn the jack bolt to adjust the pitch
③Adjust the arm until the front side stays in a
horizontal line.
④Tighten the locking nuts.

17
FAQ: What if the fabric wraps unevenly or the arms cannot open at the same time?
Answer: Check the stability of the two arms and adjust the front handlebar wrist of the faster
arm outwards accordingly.
◎Hang the Hand Crank on the Rotation Ring. You can rotate the Hand Crank in a
Clockwise/Anticlockwise direction to stretch/contract the awning flexibly.
◎When the awning is fully extended, the arm link on both sides is about 8” from the edge,
but it must be noted that the distance between the two sides must be consistent. Otherwise,
it will cause uneven stretching of the product.

18
Questions
Answers
When I open the awning, why the
front bar will pull the Fabric and
Valance toward one end?
A1: There are two possible reasons for uneven
product stretching:
1: The fabric is not evenly rolled.
2: The distance between the two ends of the bent
arm is inconsistent.
What should I do if the front bar pulls
the Fabric and Valance toward one
end?
A2: You should check if the fabric rolled evenly and
adjust the arm bar link by follow these steps:
1: First, take back the awning and fix the arm with
straps to prevent the spring from hurting people.
2: Adjust the distance between the arm bar link and
both ends to be consistent, about 8”.
3: Reinforce the screws of the link of the arm bar
so that it is not easy to slide.
Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd.Suite 250, 9166 Anaheim Place, Rancho
Cucamonga, CA 91730
Made In China
REP
EC
SHUNSHUN GmbH
Römeräcker 9 Z2021,76351
Linkenheim-Hochstetten,Germany
REP
UK
Pooledas Group Ltd
Unit 5 Albert Edward House, The Pavilions
Preston, United Kingdom

Technical Support and E-Warranty Certificate
www.vevor.com/support