Vicon V1020-WIR-180 User manual

V1020-WIR-180
Multi-Sensor Camera
Installation & Operation Manual
XX304-10
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or
that the operation will be entirely error free or perform precisely as described in the documentation. This system has not
been designed to be used in life-critical situations and must not be used for this purpose.
Document Number: 8009-8304-10-00 Product specifications subject to change without notice.
Issued: 10/18 Copyright © 2018 Vicon Industries Inc. All rights reserved.
Vicon Industries Inc.
Tel: [phone]) Fax: [phone]
Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON
(800-348-4266) UK: 44/(0) 1489-566300
www.vicon-security.com

ii V1020-WIR-180 User Manual
Content
Copyright © 2018 Vicon Industries Inc. All Rights Reserved.
Contents
Preface
Copyright ............................................................................................. iv
Disclaimer.............................................................................................. iv
Acknowledgements ............................................................................... iv
Safety Information ................................................................................. iv
RoHS Compliance ................................................................................... v
Installation Recommendations................................................................ vi
Technical Support and Assistance........................................................... vi
Conventions Used in this Manual...........................................................vii
Package Contents.................................................................................viii
Chapter 1: Product Introduction
Overview ................................................................................................1
Cable ..................................................................................................1
Hardware Specifications..........................................................................2
Hardware Installation ..............................................................................3
Chapter 2: Camera Configuration
Accessing the Camera’s Configuration Menu (Graphical User Interface) ..8
Installing IP-FINDER Software............................................................8
IP-FINDER.......................................................................................11
Introduction to the IP-FINDER User Interface...................................12
Button Functions............................................................................12
Web Browser .................................................................................13
Main Screen Overview ..........................................................................14
Configuring the Camera’s Setting .........................................................15
Browsing Through the Configuration Menu.......................................16
Video - Video Configuration .................................................................17
Primary Stream 1............................................................................17
Secondary Stream ..........................................................................18
Third Stream ..................................................................................19
Audio Settings ...............................................................................20
Image - Exposure ..................................................................................21
Day/Night Settings .........................................................................24
Image - Basic Settings ...........................................................................25
Image Adjustment..........................................................................25
Basic Settings Cont. ..............................................................................26
Mirror ............................................................................................26
Digital Processing ...........................................................................26
Image - ROI...........................................................................................27
Configurations...............................................................................27
Image - Privacy Zone.............................................................................28
Configurations...............................................................................28
Image - OSD .........................................................................................29
General Settings.............................................................................29
Text Overlay ...................................................................................29
Network - Basic.....................................................................................31
IPv4 Settings ..................................................................................31
System Settings..............................................................................31
Network - Basic.....................................................................................32
IPv6 Settings ..................................................................................32
Network - FTP.......................................................................................33
Configurations...............................................................................33
Network - SSL.......................................................................................34

iii V1020-WIR-180 User Manual
Content
Copyright © 2018 Vicon Industries Inc. All Rights Reserved.
SSL Configurations.........................................................................34
Network - 802.1x..................................................................................35
802.1x Configurations ...................................................................35
Network - SNMP...................................................................................36
SNMP Configurations.....................................................................36
Network - Firewall.................................................................................37
Firewall Configurations ..................................................................37
Network - LDAP....................................................................................38
LDAP Configurations......................................................................38
Network - DDNS ...................................................................................39
DDNS Configurations.....................................................................39
Network - RTSP.....................................................................................40
RTSP Configurations.......................................................................40
Multicast (Stream 1 to Stream 3) ....................................................41
Network - GB28181..............................................................................43
GB28181 Configurations ...............................................................43
System - Date/Time...............................................................................44
Date/Time Configurations ..............................................................44
Time Setting ..................................................................................44
Time Zone Setting..........................................................................44
System - Maintenance...........................................................................45
System Information........................................................................45
Firmware Update ...........................................................................45
Backup...........................................................................................46
Restore ..........................................................................................46
System - User Management ..................................................................47
Admin Setting................................................................................47
User List.........................................................................................47
User Information............................................................................48
Event - Alarm Handler...........................................................................49
Alarm Handler Configurations........................................................49
Alarm Schedule Settings.................................................................49
Event - Motion Detection......................................................................50
Motion Configurations...................................................................50
Zone1 to Zone5 Setup....................................................................50
Motion Schedule Settings...............................................................51
Event - Sabotage Detection...................................................................52
Sabotage Detection Configurations................................................52
Sabotage Schedule Settings ...........................................................52
Event - FTP Upload................................................................................53
FTP Upload Handler Configurations................................................53
Remote Server................................................................................53
Event - SMTP Notification......................................................................54
SMTP Notification Handler Configurations......................................54
Trigger Event..................................................................................54
SMTP Server...................................................................................55
Recipient List..................................................................................55
Event - Network Storage.......................................................................56
Network Storage Configurations....................................................56
Trigger Event..................................................................................56
Recipient Setup..............................................................................56
Login Certificate.............................................................................57
Mount and Remove Network Storage ...........................................57
Event - Relay Handler............................................................................58
Relay Handler Configurations.........................................................58
Event - SD Record .................................................................................59
SD Record Handler Configurations .................................................59
SD Information...............................................................................59
Alarm/Motion/Sabotage Detection Settings ....................................61
Record Type Selected: Snapshot ....................................................61
Alarm/Motion/Sabotage Detection Settings ....................................62
Record Type Selected: Video ..........................................................62
Trigger Scheduled Settings .............................................................63
Day/Time Inclusion Filter.................................................................63

iv V1020-WIR-180 User Manual
Preface
Copyright © 2018 Vicon Industries Inc. All Rights Reserved.
Preface
Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written consent from Vicon
Industries Inc.
Disclaimer
The information in this document is subject to change without prior notice
and does not represent commitment from Vicon Industries Inc. However, users
may update their knowledge of any product in use by constantly checking its
manual posted on our website: http://www.vicon-security.com. Vicon shall
not be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use of any product, nor for any infringements upon the rights
of third parties, which may result from such use. Any implied warranties of
merchantability or fitness for any particular purpose is also disclaimed.
Acknowledgements
Vicon and its logo are registered trademarks of Vicon Industries Inc. All
other product names mentioned herein are registered trademarks of their
respective owners.
Safety Information
Before installing and using the device, note the following precautions:
▪Read all instructions carefully.
▪Follow all warnings and cautions in this manual.
▪Do not place the unit on an unstable surface, cart, or stand.
▪Do not use the camera in extreme temperature conditions. Please use the
camera within -40ºC to 55ºC. Air vent is required at high temperature.
▪Do not use or store the camera in humid environment. It may cause poor
image quality.
▪Do not use the camera in unstable lighting conditions. Inconsistent
lighting or flickering may cause poor image.
▪Never use the camera close to gas or oil leak. It may not operate properly.
▪Do not disassemble the camera. There is no user serviceable part inside.
▪Do not drop the camera or apply force on it. It may cause a malfunction.
▪Avoid using the system near water, in direct sunlight, or near a heating
device.
▪Never face the camera to strong light for long periods of time. It may
damage the CMOS sensor.

vV1020-WIR-180 User Manual
Preface
Copyright © 2018 Vicon Industries Inc. All Rights Reserved.
RoHS Compliance
Vicon RoHS Environmental Policy and Status
Update
Vicon is a global citizen for building the digital
infrastructure. We are committed to providing green
products and services, which are compliant with
European Union RoHS (Restriction on Use of Hazardous Substance in
Electronic Equipment) directive 2011/65/EU, to be your trusted green
partner and to protect our environment.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1%
or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent Chromium
(Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) < 0.1% or
1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm.
In order to meet the RoHS compliant directives, Vicon has established an
engineering and manufacturing task force to implement the introduction
of green products. The task force will ensure that we follow the standard
Vicon development procedure and that all the new RoHS components and
new manufacturing processes maintain the highest industry quality levels
for which Vicon are renowned.
The model selection criteria will be based on market demand. Vendors and
suppliers will ensure that all designed components will be RoHS compliant.
How to recognize Vicon RoHS Products?
For existing products where there are non-RoHS and RoHS versions, the
suffix “(LF)” will be added to the compliant product name.
All new product models launched after January 2013 will be RoHS compliant.
They will use the usual Vicon naming convention.

vi V1020-WIR-180 User Manual
Preface
Copyright © 2018 Vicon Industries Inc. All Rights Reserved.
Installation Recommendations
Ensure you have a stable, clean working environment. Dust and dirt can get
into components and cause a malfunction. Use containers to keep small
components separated.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
▪A Philips screwdriver
▪A flat-tipped screwdriver
▪A grounding strap
▪An anti-static pad
Using your fingers can disconnect most of the connections. It is recommended
that you do not use needle-nose pliers to disconnect connections as these
can damage the soft metal or plastic parts of the connectors.
Technical Support and Assistance
1. For the most updated information of Vicon products, visit Vicon’s website
at www.vicon-security.com.
2. For technical issues that require contacting our technical support team or
sales representative, please have the following information ready before
calling:
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages
Warning!
1. Handling the unit: carry the unit with both hands and handle it with care.
2. Maintenance: to keep the unit clean, use only approved cleaning products
or clean with a dry cloth.

vii V1020-WIR-180 User Manual
Preface
Copyright © 2018 Vicon Industries Inc. All Rights Reserved.
Conventions Used in this Manual
Warning:
Information about certain situations, which if not observed,
can cause personal injury. This will prevent injury to yourself
when performing a task.
CAUTION!
CAUTION!CAUTION! Caution:
Information to avoid damaging components or losing data.
Note:
Provides additional information to complete a task easily.

viii V1020-WIR-180 User Manual
Preface
Copyright © 2018 Vicon Industries Inc. All Rights Reserved.
Package Contents
The V1020-WIR-180 package contains the following accessories:
Name Quantity
IP camera 1
Quick installation guide 1
Accessory pack 1

1V1020-WIR-180 User Manual
Chapter 1: Product Introduction
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
Chapter 1: produCt IntroduCtIon
Overview Cable
RJ45
Alarm OUT
Alarm IN
Audio OUT
Audio IN
Reset to default button
Power IN
(DC12V 2.5A/AC24V 1.5A)

2V1020-WIR-180 User Manual
Chapter 1: Product Introduction
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
Hardware Specifications
Camera
▪Image sensor: 20MP, 4pcs 1/1.8” 5MP CMOS progressive sensor
▪Maximum resolution: 4 ch x (2592 x 1944)
▪Lens: 4 Fixed Lens 5.5mm F1.8
▪IR effective distance: 30M
▪Day and night: Auto ICR
▪Minimum Illumination: Color 0.1 LUX/F1.8, B/W 0 LUX/F1.8
▪Electronic shutter speed: Auto/Manual 1/7~1/20000
▪Gain control: Global (Sync Brightness)/Auto/Manual
▪Backlight compensation: Yes
▪White balance mode: Auto/Manual
▪Image settings:
– Brightness, Contrast, Saturation, Sharpness, Mirror, Flip
Video
▪Video compression: H.265/H.264/MJPEG
▪Video streaming: Triple streaming
▪Video resolution: 2592x1944/1080p/720p/640x480/640x360/320x240
▪Frame rate: @30 fps
▪Bit rate: 64K~8000K
Network
▪Interface: 1000Mbps Ethernet, RJ-45
▪Supported protocols: TCP/IP, UDP, ICMP, IPv4, IPv6, SNMP v2c/v3, QoS,
HTTP, HTTPS, LDAP (client), SSL, SMTP, FTP, RTSP, UPnP, DNS, NTP, RTP,
RTCP, DynDNS, Zero Configure
▪ONVIF: Profile S, Q, G
▪Users: Live viewing/Administrator for up to 10 clients
▪Browsers: Internet Explorer, Google Chrome, Mozilla, Firefox
Event Management
▪Event trigger: Motion detection, Tampering detection, Alarm In/Out
▪Notifications: Send/Record message via e-mail/FTP/NAS/SD card, record
JPG/mp4
General
▪Power supply: IEEE 802.3at, DC12V/24VAC terminal block
▪Power consumption: 25W (max.)
▪Support SD Card up to 128GB
▪DI/DO: DI*1, DO*1
▪Audio: IN*1, OUT*1
▪Weight: 5.5 lb (2500g)
▪Dimension: Ø 7.7 in. (196 mm) x 7.4 in. (188.4 mm) (H)
▪Operating Temp.: -40°F ~ 131°F (-40°C ~ 55°C)
▪Humidity: 10% ~ 90%RH (no condensation)
▪Certification: CE/FCC class A
▪Vandal Resistant: IK10
▪Weatherproof: IP66
▪Application: SDK available for application development

3V1020-WIR-180 User Manual
Chapter 1: Product Introduction
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
Hardware Installation
1. Use an Allen key to remove the cap on the bottom of the camera. 2. Loosen the 4 screws on the iron sheet and remove the iron sheet.
External Network Cable
Iron sheet
External Network Cable
Iron Sheet

4V1020-WIR-180 User Manual
Chapter 1: Product Introduction
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
Top cove
r
3. Loosen the 4 captive screws on the dome bubble and open it.
Top Cover
4. After opening the dome, use the tool provided to loosen the 4 screws
and remove the bottom cover.
Main body
with modules
Bottom cover
Main Body
with Modules
Bottom Cover

5V1020-WIR-180 User Manual
Chapter 1: Product Introduction
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
5. Fix bottom cover in the location where the camera is to be installed
(wall or ceiling).
5.1 Place installation sticker (template) on the installation location
(wall or ceiling).
5.2 Bore 4 holes according to the marks on the installation sticker.
5.3 Use the 4 expansion bolts provided in the screw installation package
and insert them into the 4 holes.
5.4 Use the 4 screws provided in the screw installation package and
screw them into the expansion bolts to fix the bottom cover in the
installation location (wall or ceiling).
6. Insert the main body with modules back into the bottom cover. Fix them
by the 4 screws previously loosened (on step 3).

6V1020-WIR-180 User Manual
Chapter 1: Product Introduction
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
Right or Left
Up or Down
Manual Easing
Gear
Manual Easing
Gear
7. Rotate the manual easing gear (both sides) to loosen and adjust the
viewing direction that the camera will monitor. The camera idirection can
be adjusted up/down or left/right directions.
Manual Easing
Gear
Right or Left
Up or Down
Manual Easing
Gear
8. After confirming the direction, rotate the manual easing gear (both sides)
to fix the camera direction.
Manual Easing
Gear
Manual Easing
Gear
Manual Easing
Gear
Manual Easing
Gear

7V1020-WIR-180 User Manual
Chapter 1: Product Introduction
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
9. Retighten the 4 captive screws on the dome to secure it in place.

8V1020-WIR-180 User Manual
Chapter 2: Camera Configuration
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
Chapter 2: Camera Configuration
Accessing the Camera’s Configuration
Menu (Graphical User Interface)
By default, the camera is set to obtain an IP address via DHCP. If your network
does not have a DHCP server, run the IP Finder and click “Search;” you will
find the device IP, as shown in the following section.
You can access the camera via a web browser or IP-FINDER software. The
following information outlines the instructions for each method.
Installing IP-FINDER Software
1. Download the IP-Finder installer file; the IP-FINDER tool (Discovery tool)
can be gotten from the Vicon website, Software Downloads..
2. Unzip the IP-FINDER file to a location on the hard drive.
3. Once unzipped, double click on the setup file to start the installation
program.
4. Click the Next button on the Welcome screen to continue.
Next button
Note: If IP-FINDER is already installed, you can skip this section and continue
to the next section IP-FINDER on page 11.

9V1020-WIR-180 User Manual
Chapter 2: Camera Configuration
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
5. Confirm the directory that the program will be installed on. To specify
a different folder, click on the Browse button and locate the desired
installation folder.
Next button
Browse button
Disk Cost
button
User accounts
8. Click on the Next button to continue.
6. To check the available drives you can install the software to and their
available and required disk space, click on the Disk Cost button.
7. Specify which user accounts on the computer can access the program;
the options are Everyone and Just me.

10 V1020-WIR-180 User Manual
Chapter 2: Camera Configuration
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
Next button
9. Click on the Next button to begin installation.
Close button
10. Once the installation process is complete, click on the Close button to
finish. A shortcut will be created on the desktop.

11 V1020-WIR-180 User Manual
Chapter 2: Camera Configuration
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
IP-FINDER
1. Locate and open the IP-FINDER software shortcut on the desktop.
Camera
List
4. You can access the menu by double clicking the camera’s IP address
under Camera List. The IE will be opened automatically.
2. When the program is launched, it will begin searching the network for
IP cameras automatically (the search will last for up to 90 seconds). You
can also manually search cameras by clicking on the Search button.
3. Once the camera is discovered, it will show the following information:
▪Model Name
▪IP address
▪MAC address
▪UUID
▪Serial Number
▪Version

12 V1020-WIR-180 User Manual
Chapter 2: Camera Configuration
Copyright © 2018 Vicon Industires Inc. All Rights Reserved.
Introduction to the IP-FINDER User Interface Button Functions
Preview
Camera List
Device
Mark
Control Bar
Information
UI Block Description
Control Bar Contains [Search], [Assign IP], [Home Page] and [Firmware
Upgrade] buttons.
Preview Displays the selected camera image.
Information Displays the selected camera information such as Model Name,
IP, MAC, UUID, SN and Version.
Camera List
Lists the cameras discovered by the search function. Each camera
shows the “IP”, “Status”, “Model Name” and “Device
Mark”. Users can also click the column headers to sort the list.
Device Mark Asterisk sign indicates that this device has “Preview”, “Assign
IP” and “Firmware Upgrade” functions.
Function Button Description
Search Discovers IP cameras available on the network.
Assign IP Changes the IP address of the camera.
Home Page Opens the web browser to the home page of
the camera.
Firmware
Upgrade Upgrades the camera firmware.
Search
When the [Search] button is clicked, the application will start searching
cameras on the network. To stop searching, click the [Done] button.
Assign IP
When the [Assign IP] button is clicked, a pop-up window “IP Address
Configuration” will appear, providing options to use DHCP or static IP address.
Home Page
To view the home page of a particular camera, double click on the camera in
the list; the web browser will open and redirect to the home page. To access
the home page of two or more cameras, tick the box of the cameras you
want to view and click on the [Home Page] button.
Firmware Upgrade
To update the camera firmware, tick the box of the cameras you want to
update and click on the [Firmware Upgrade] button. Follow the on-screen
prompts to complete the upgrade. If the camera does not support firmware
upgrade, a pop-up window will be displayed.
NOTE: Different IP camera models use different firmwares, please do NOT
update the firmware of different models using the same firmware.