Victor E Lock ER-043 Manual

B04/28/06

B04/28/06

1. Outer Housing Assembly (1 each)
2. Water Seal (1 each)
3. Spindle, Spring Latch / Passage
Function (1 each)
3.1 Spindle, Spring Latch / Storeroom
Function (1 each)
4. Nylon Washer (2 each)
5. 2.5mm Allen Wrench (1 each)
6. Lever Handle with Set Screw (2 each)
7. Remote Controllers (2 each)
8. Inner Housing Assembly (1 each)
9. M5-0.8P Machine Screw (4 each)
10. Push Pin
11. Inner Escutcheon (1 each)
12. M3-0.5P Machine Screw (2 each)
13. 2mm (2 each)
14. Indicator (1 each)
15. Dead Bolt (1 each)
16. Battery Housing (1 each)
17. 4mmx20mm Wood Screw (8 each)
18. Spring Latch (1 each)
19 Tailpiece, Dead Bolt (1 each)
20. Coil Spring (1 each)
21. Plastic Snap Bushing (1 each)
22. Strike Plate, Dead Bolt ( (1 each)
23. Strike Plate, Spring Latch (1 each)
D1
1
5
5
18
11 122 12
13
8
7
21
15
4
4
2
20
17
17
17
17
10
9
9
9
3
19 14
16
6
6
EP-043 Manual Rev. B Date 04/28/06
Page 3
INSTALLATION INSTRUCTION MODEL ER-043
PARTS LIST
US PAT. #6725693B2
17
17
17
17
22
23
3.1

B04/28/06

I
04/28/06
B

B04/28/06

B04/28/06

UNSCREW AND REMOVE JIGS
B04/28/06

ER-043 Manual Rev. B Date 04/28/06
Page 9
INSTALLATION INSTRUCTION MODEL ER-043
Step1B
NEW DOORS ALREADY WITH CYLINDRICAL HOLES
IF YOUR DOOR HAS ONE CYLINDRICAL HOLE
a. Bore out 1” hole with a 1” hole saw on the bottom of Edge JIg (Figure 6).
b. Insert Hole Locator into Spring Latch hole. Insert bottom of Edge Jig into Hole Locator and screw in Edge Jig to door edge.
Proceed with STEP 1 (Figure 7).
IF YOUR DOOR HAS TWO CYLINDRICAL HOLES
a. If distance between two holes is 5” follow the same procedures as above.
b. If distance is 4”, 4-1/2”, or 5-1/2” between cylindrical holes please purchase special Gear Box Assembly from Victor e-lok.
Figure 6
Figure 7
5"
INSERT HOLE LOCATOR
INTO SPRING LATCH HOLE
EDGE JIG
BORE OUT 1" HOLE
WITH A 1" HOLE SAW

Step2
PREPARE THE PARTS BEFORE INSTALLTION
a. Check if door is Right or Left hand. If you are facing the outside of the door and the hinge is on the right, it is a Right
Hand door (and visa versa). Make sure your Kit matches your door type (Figure 8).
b. Set the Rotor to correct position. R is for right hand and L is for left hand (Figure 9).
c. Unscrew 2.0mm Machine Screws on both upper sides of Inner Escutcheon and remove Escutcheon. d.
Insert Push Pin into pinhole on left side of Inner Escutcheon then depress to release and remove Battery Housing
(Figure 10).
Rotor
ER-043 Manual Rev. B Date 04/28/06
Page 10
INSTALLATION INSTRUCTION MODEL ER-043
RH
Right Hand
LH
Left Hand
LHR
Left Hand
Reverse
RHR
Right Hand
Reverse
INSIDE
OUTSIDE
Figure 8
Figure 10
Rotor
Figure 9
INSERT PUSH PIN
AND REMOVE
BATTERY HOUSING
US PAT. #6725693B2 US PAT. #6725693B2
LEFT HAND RIGHT HAND
UNSCREW SCREWS ON
BOTH SIDE TO REMOVE
INNER ESCUTCHEON

2
3
/
8
2
3
/
4
P
U
LIFT THE B UTT ON UP
PUSH ALL THE WAY TO THE RIGHT
Figure 11
ER-043 Manual Rev.Date 04/28/06
Page 11
INST ALLA TION INSTR UCTION MODEL ER-043
""
B

drilling point marks.
B
04/28/06

Step 5
MOUNT DEAD BOL T AND SPRING LATCH
a. Insert Dead Bolt and Spring Latch into bored holes (Figure 17).
b. Loosely mount Dead Bolt and Spring Latch with 4mmx20mm Wood Screws. Test both Dead Bolt and Spring Latch to
confirm they work smoothly. Tighten screws.
Step 6
INSTALL SPINDLE FOR SPRING LATCH
Figure 17
Figure 18
OUTSI
D
E
ER-043 Manual Rev. B Date 04/28/06
Page 13
INSTALLATION INSTRUCTION MODEL ER-043
For Entry function use
For Storeroom function use

B04/28/06
and hold in place
hair.

B28/04/06

B
04/28/06

square
light is solid. If Red Light glows, teaching was not successfull.
Insert Push Pin square into upper right side of Inner Housing Assembly for 5 seconds, green light will glow for 2 seconds. All codes
have been deleted.
BDate 04/28/06

be locked.
B 04/28/06
Do not slam door or allow strong winds to close door. These actions will damage the electronics of the lock.
*Note: Press down lever handle to release dead bolt, then push or pull to open door. Do not push or pull door before releasing
dead bolt.