VictoriaPlum MODE BATHROOMS 4 PANEL FOLDING BATH SCREEN User manual

4 PANEL FOLDING BATH SCREEN
LH RH
VictoriaPlum.com
0344 804 48 48
Refer To Sheet 8 For Relevant Product Codes

1
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Additional Notes
Please inspect this product upon delivery, any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage or defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note: Aluminium is a soft metal, and undergoes a series of extrusion,
fabrication, polishing and anodising processes in order to create your finished
shower . Some light surface marks are normal, and is a result of thescreen
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.
Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
TOOLS REQUIRED
This product is heavy and may require two people to install.
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTION
PART IMAGE PART IMAGE
Drill
Flat-head
Screwdriver
Cross head
Screwdriver
Mallet
Silicone Sealant
PZ1

2
1x Upright Profile Cover Cap
1x Wall Profile
3x Bottom Seals
1x Plastic Bushing
1x Bottom Strip Cap A
1x Bottom Strip Cap B
1x Drip Strip
3x Screws 4x12
1x Wall Profile Cover Strip
1x Glass Panel
1x Wall Profile Cover Cap
3x Wall Plugs
3x Screws 4x30
3x Upright Seals
24x Hinge Cover Cap
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(9)
(8)
(10)
(11)
(12)
(13)
(14)
(15)
(2)
(1)
(3)
(5)
(6)
(7)
(8)
(12)
(13)
(14)
(9)
(10)
(11)
(4)
(15)
ASSEMBLY DRAWING + BOX CONTENTS PARTS LIST
BEFORE STARTING THIS INSTALLATION - CHECK THAT THE CONTENTS IN
THIS BOX MATCH THE CONTENTS SHOWN IN THE ASSEMBLY DRAWING

ASSEMBLY INSTRUCTIONS
If you require help, we advise you to contact a competent plumber
Installation Steps
FITTED BATH SCREEN DRAWING
LH
RH
3
900
2 0
10
9 0 0 2 0
10

4
Step 1 MARK WALL FIXING POSITIONS AND DRILL WALL HOLE
MAKE SURE THE BATH IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS
SHOWER SCREEN.
6mm
Take Care Not To
Damage Wall Surface
Screws 4x30

3.0mm
ST4X12
x3
x3
1
2
3
5
Step 2 SLIDE GLASS PANEL ON TO THE WALL PROFILE
Step 3 FITTING THE PROFILES
How to adjust the width of the 4 panel
folding bath screen
MAXIMUM ADJUSTMENT
MINIMUM ADJUSTMENT
Glass panel
Glass panel
Vertical profile
0~20mm
Vertical profile
Wall profile
Wall profile
L=0~20mm
L 5mm/R≥ ≥10mm
R
L 5mm/R≤ ≥15mm
Take care not to drill to the glass
INSIDE
4

6
Step 4 FITTING THE SEALS
view from outside
Step 5 FITTING THE DRIP STRIP
1
1
2
3
1
4 5
2 3
2

Silicone (outside edge only) where the
vertical profile meets the wall.
Step 6 FITTING THE TOP CAPS AND SILICONE THE OUTSIDE EDGES
Step 7 FOLD THE DOOR
3
2
1
1
2
3
7

CARE AND MAINTENANCE
COMMITMENT TO QUALITY
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier accepts
no liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
It is our intention that the quality and functions of this product
are of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact out customer services quoting
the following:
Product name: 4 PANEL FOLDING BATH SCREEN
Product code: JBS906L JBS906R
Customer help line number:0344 804 48 48
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
8

INSTALLERS NOTES
9

INSTALLERS NOTES
10

The packaging you have received with your product is 100% recyclable.
It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.
V02/04/2017
Victoria Plum Limited, Bridgehead Business
Hessle, HU13 0DG
Park
EN 14428:2015
Shower enclosures with aluminium
profiles and safety glass
Essential
characteristics
Performance Harmonised
technical
specification
Cleanability
Impact
resistance/shatter
properties
Pass
Pass
PassDurability
Clause 4.2 of
14428:2015EN
Clause 4.3 of
14428:2015EN
Clause 4.4 of
14428:2015EN
Victoria Plum Limited, Bridgehead Business
Hessle, HU13 0DG
Park
17
DOP No.: J170103001-1
Shower enclosures with aluminium
profiles and safety glass
Essential
characteristics
Performance Harmonised
technical
specification
Cleanability Pass
Pass
PassDurability