VictoriaPlum PFLQ699 User manual

ASSEMBLY INSTRUCTIONS
FRAMELESS PIVOT 2 DOOR QUADRANT
V03/05/2014

BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Additional Notes
Please inspect this product upon delivery. any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage of defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS-AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note--alumimium is a soft metal, and undergoes a series of extrusion.
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.
Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
TOOLS REQUIRED
This product is heavy and may require two people to install.
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-head
Screwdriver
Cross head
Screwdriver
Hammer
Silicone Sealant
1

2
(2)
(1)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
ASSEMBLY INSTRUCTIONS-DRAWING
(1) 2. x Wall Bracket
(2) 2. x Wall Post
(3) 2. x Vertical Profile
(4) .
(5) .
(6)
2
.
x Moving Door
(10).
8x Wall Plugs
8x Screws 4x30mm
2x Handle
(7) .
(8) .
(9) .
(13) .
(12) .
(14)
12
.
x Screw Cover caps
(11)
12
.
x Screws 4x12mm
12x Screw Cover Cap Washers
1x Curved End Cover Cap
1x Bottom Seal
1x Drip Strip
2x Magnet Seal (Moving Door)

ASSEMBLY INSTRUCTIONS
If you require help, we advise you firstly contact a competent plumber
Installation Steps
Step 1
3
THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL,
AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE / WET
WALL PANEL.

MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE
INSTALLING THIS SHOWER PANEL / DOOR.
Step 2
Step 3
4
6mm
4x30
x4
x4
x4
x4
20
20

Step 4
Step 5
5
12
12

6
Step 6
Step 7
x12
x12
3.0mm
How to adjust the width of the
hinged door
Minimum 10mm
internal overlap required
Glass panel
Glass panel
Vertical profile
Vertical profile
Wall profile
Wall profile
Wall
Wall
Maximum adjustment
Minimum adjustment

Step 8
7
Silicone (outside edge only) where the
vertical profiles meet the wall, and the
glass panel meet the tray.

COMMITMENT TO QUALITY
It is our intention that the quality and functions of this product
are of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact out customer services quoting
the following:
Product name:
Customer help line number:0844 804 45 45
CARE AND MAINTENANCE
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier accepts
no liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
8
Frameless pivot 2 door quadrant
Product code: PFLQ699

9

The packaging you have received with your product is 100% recyclable.
It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.