Videomitter MIT500 User manual

© 2023 System Q Ltd
1
MegaMitter Video TX & RX Pair - Wireless 2MP AHD Transmission
VideoMitter is a registered trademark of System Q Ltd
Document ref: MIT500
VideoMitter.com
MIT500 - Quick Start Guide
User Information
· The product must be installed in a clean, dry
environment where it will not be exposed to
high temperatures, moisture or excessive
dust.
· Do not touch the product or any of its
connections with wet hands.
· Ensure the power is switched off if the
product is not in use for a long period of time.
· There are no user serviceable parts in the
product and opening or attempting to repair
the product will void the warranty.
Full Instruction Manual
www.systemq.com/PDF/
manual/xMIT500.pdf
· Only use a regulated 12V DC power supply. Note: power supplies are sold separately.
· Do not install or use the device if the power cable or video connections are damaged.
· Do not use alcohol or solvents to clean the product, only clean using a damp cloth.
· Before installation it is recommended to connect the whole transmission setup on a bench or
local to the DVR / monitor to ensure compatibility and that all parts are in working order.
Introduction
The 2MP HD MegaMitter can transmit an AHD CCTV camera wirelessly. Ensure the camera
connected has a 4-in-1 selectable output set to AHD or have a AHD video output (2MP). This
product will not work with higher than 2MP cameras.
Ensure the MegaMitters are installed in line of sight with no obstructions between the TX & RX. Up
to 4 pairs of MegaMitters can be used on the same site but it is recommended to use directional
antennas when using multiple sets.
Connections & Controls
Powering
The MegaMitters need powering with a fullyregulated
12V DC power supply individually. When they are
powered up a red power light will come on.
Antenna
The small antenna simply screws on to
the top of the MegaMitters. Optional
antennas are available to increase
transmission range.

This symbol indicates that equipment must not be mixed with general household waste. For treatment, recovery and recycling please return to your local designated
WEE/CG0783SS collection point as defined by your local council.
© 2023 System Q Ltd
2
MegaMitter Video TX & RX Pair - Wireless 2MP AHD Transmission
VideoMitter is a registered trademark of System Q Ltd
Document ref: MIT500
All specificationsare approximate. System Q Ltd reservesthe right to change product specificationsor features without notice. Whilst every effort is
made to ensure that these instructionsare complete and accurate, System Q Ltd cannot be held responsible for any losses,no matter how they arise,
from errorsor omissionsin these instructions,or the performance or non-performance of the equipment refered to.
Connecting Video and Camera
Connect the video input feed to the video BNC socket on the Transmitter and video output feed to
the BNC socket marked on the Receiver.
To power the camera via power pass-through connect the power out cable (1) on the transmitter to
your camera’s power in female lead.
Note - If you press and hold the reset button by mistake you will need to re-pair the units.
Pairing
The MegaMitters are supplied tested and paired up. Only one receiver can receive video from one
transmitter. When both the TX & RX are powered up within transmission range the green light will
illuminate to indicate they are connected.
Pairing Process - As supplied the MIT500s are already paired, but if they do need pairing
followthe process below;
1. Connect 12V DC Power to both Tx and Rx. Press the PAIR button down on the RECEIVER
for 3 seconds. The Link LED will start to flash.
2. Within 30 seconds press and hold the PAIR button on the TRANSMITTER until the link LED
starts flashing.
3. Once pairing is complete both Link LEDs will display solid Green. If a monitor is connected to
the RECEIVER it will display a signal strength bar at the top left hand corner of the display.
Specifications
Frequency
2.4Ghz
Video Format
AHD 720p / AHD 1080p
Range
200m (as supplied)
Max Range
Up to 1Km (with additional aerials)
Audio
No
IP Rating
IP65 (providing connections are made IP65)
Antenna
RP-SMA
Video Connection
BNC
Input Voltage
12V DC
Current Consumption
Tx 250mA Rx 140mA
Power Connection
2.1mm DC Socket
Operating Temperature
-30 ~70ºC
Delay
150mS Max
Modulation
16QAM/QPSK/BPSK
Transmission Channels
19 (FHSS – maximum 4 pairs per site
Pair separation distance
Minimum of 2m apart
Dimensions
110mm x 95mm x 25mm (Not including aerials or wires)