Videosec PS04PGE+1PD User manual

4-Port Gigabit+1GE(PD) PoE Switch
User Guide
PS04PGE+1PD

- 1 -
Package Contents
Check the following contents of your package:
 PoE Switch x 1
 User’s Manual x 1
 Rubber Feet x 4
If any part is lost and damaged, please contact your local agent immediately.
1. Introduction
Thank you for choosing This PoE Switch. The PoE Switch is 5-Port 10/100/1000Mbps Auto-Negotiation RJ45
Port. Among them, port1~4 is PSE port, support 32W output. Port5 is PD port, support 60W input. This PoE
Power supply support external power supply and PoE.
4-Port Gigabit+1GE(PD) PoE Switch is easy to install and don’t need to configuration. With outstanding
performance and quality, the 5-port 10/100/1000Mbps desktop PoE switch is an ideal choice for expanding
your home or office network.
2. Hardware Description
2.1 Front Panel
The Front Panel of the PoE Ethernet Switch Consists of 5-Port Ethernet Ports. The LED indicators are also
located on the panel.

- 2 -
LED indicator
LED
Color
Function
PWR
Green
Off: No Power supply.
Light: Indicates the switch has power.
10/100M
Orange
Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is successfully
established at 10/100Mbps.
Blink: Indicates that the Switch is actively sending or
receiving data over that port.
1000M
Green
Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is
successfully established at 1000Mbps.
Blink: Indicates that the Switch is actively sending or
receiving data over that port.
PoE
Orange
Off: No PoE powered device (PD) connected.
Light: There is a PoE PD connected to be port, which
supply power successfully.
Blink: Indicates port abnormal power supply.
Max
Orange
Off: indicate the PoE usage is less than 80%.
Light: Indicate the PoE usage is over 80%, No power
may be supplied if additional PD are connected.
Blink: Indicate the PoE usage is over 100%.
2.2. Rear Panel
The rear panel of the PoE Switch indicates a DC inlet power socket.
*** DC：DC Power Socket, connect the power adapter.

- 3 -
3. Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please follow the
following instructions in avoid of incorrect installation causing device damage and security threat.
Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with wet
cloth or liquid;
Do not place the switch near water or any damp area. Prevent water or moisture from entering the
switch chassis;
Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a
fall;
Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of
obstruction;
Make sure that the operating voltage is the same one labeled on the switch;
Do not open the chassis while the switch is operating or when electrical hazards are present to avoid
electrical shocks.
3.1. Desktop Installation
Install the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each
corner of the Switch in case of the external vibration. Allow adequate space for ventilation between the
device and the objects around it.
3.2 Turn on the switch
The PoE switch can be used with DC power supply. Powering on the switch, it will automatically initialize
and its LED indicators will respond as follows:
1) Firstly, the Power LED indicator will light up.
2) Then, the data LED indicators will flash momentarily for one second, which represents a resetting of the
system.

- 4 -
Specifications
Model
4-Port Gigabit+1GE(PD)
Standard
IEEE802.3, IEEE802.3u,IEEE802.3ab, IEEE802.3az, IEEE802.3x,
IEEE802.3af, IEEE802.3at
Network -
Media(Cable)
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e,6 cable (≤100m)
MAC Address Table
2K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T: 1488095pps/Port
Switching Capacity
10G
Dimensions (L*W*H)
140*92.5*28mm
Fan
Fanless
Power supply
55V DC/1.1A AC/DC Adapter or PoE
PSE Port
Port1~4
PSE Power on RJ45
Mode A 1/2(+),3/6(-)
PSE Power Output
Voltage: 55V DC Power: 32W(Max)
PSE Power Budget
55W
PD Port
Port5
PD Power on RJ45
Mode A: 1/2(+),3/6(-) or Mode B: 4/5(+),7/8(-)
PD Port input
60W
Temperature
Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F )
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F )
Humidity
Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing