Videosec PSH04GE+4GE User manual

User Guide
8-Port Gigabit PoE Switch witch LCD display
PSH04GE+4GE

Package Contents
Check the following contents of your package:
 PoE Switch x 1
 User’s Manual x 1
 Power Cord x 1
 Accessories(hanging ears*2, Rubber Feet*4, screw*8)
If any part is lost and damaged, please contact your local agent immediately.
1. Introduc on
Thank you for choosing this PoE Switch. The provides 8-10/100/1000Mbps RJ45 port, all ports support
MDI/MDIX func on. Among them 1-4 ports have PSE func on, using 4 twisted-pair cable to the terminal
equipment of power supply at the same me, the output power up to 60W, complies with
IEEE802.3 af/at standard, can automa cally detect iden fica on standard of electrical equipment and
through the cable power supply to them.
The LCD not only can display the PoE work status, accurate judgment port of load, can also help customer
and engineer mely discover and solve the network failure, improve work efficiency and quality.
2. Hardware Descrip on
2.1 Front Panel
The Front Panel of the PoE Ethernet Switch Consists of Ethernet Ports. The LCD Display and LED indicators
are also located on the panel.
- 1 -

LED indicator
LED Color Func on
PWR Green Off: No Power supply.
Light: Indicates the switch has power.
LNK/ACT
Orange
Off: No device is connected to the corresponding port
Light: Indicates the link through that port is successfully
established at 10/100Mbps.
Blink: Indicates that the Switch is ac vely sending or
receiving data over that port.
Green
Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is
successfully established at 1000Mbps.
Blink: Indicates that the Switch is ac vely sending or
receiving data over that port.
PoE Orange
Off: No PoE powered device (PD) connected.
Light: There is a PoE PD connected to be port, which
supply power successfully.
Blink: Indicates port abnormal power supply.
2.2. Rear Panel
The rear panel of the PoE Switch indicates an AC inlet power socket, which accepts input power from
100 to 240V AC, 50/60HZ.
2.3. LCD Features
The PoE Switch is with the func on of the LCD display and PoE Ethernet switch. The LCD can display
the working condi n of PoE port not only , s ll can accurately show the state of each port, such as:
Output power, Overload, Short circuit, Light load, Low voltage, Over voltage,High temperature, and so on...
- 2 -
Fan
Power socket
Grounding column

3. Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please follow the
following instructions in avoid of incorrect installation causing device damage and security threat.
Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with wet
cloth or liquid;
Do not place the switch near water or any damp area. Prevent water or moisture from entering the
switch chassis;
Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a
fall;
Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of
obstruction;
Make sure that the operating voltage is the same one labeled on the switch;
Do not open the chassis while the switch is operating or when electrical hazards are present to avoid
electrical shocks.
3.1. Desktop Installation
Install the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each
corner of the Switch in case of the external vibration. Allow adequate space for ventilation between the
device and the objects around it.
- 3 -

3.2. Rack-mountable Installaon
The switch is rack-mountable and can be installed on an EIA-19 inch equipment rack. To do this, first, please
install the mounng brackets on the switch’s side panels (one on each side), secure them with the included
screws, and then use the screws provided with the equipment rack to mount the switch on the 19 inch rack.
3.3 Turn on the switch
Please plug the power supply into the switch, the internal power system of the switch can Auto-regulate the
working power according to the actual inputpower. When the switch is power on, the power indicator will
be light on the front panel of the switch shines.
Note: Please confirm the voltage is correct before power on, otherwise the switch will be damaged.
(There is a power supply socket on the back panel of the PoE Ethernet switch. The power input is:
100V-240Vac, 50/60Hz.)
- 4 -

Specifica ons
Model 4GE(PoE)+4GE
Standard IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3az, IEEE802.3x,
IEEE802.3af, IEEE802.3at
Network -
Media(Cable)
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e cable (≤100m)
LCD Display
Support
MAC Address Table
8K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T: 1488095pps/Port
Switching Capacity
16G
Dimensions (L*W*H)
280 *179 *44.5 mm
Fan
Power Input
AC: 100~240V, 50/60Hz
Power output
55VDC /3.6A
PoE Port
Port1~4
PoE Power on RJ45
Twisted-pair polarity: 1/2(-),3/6(+);and4/5(+),7/8(-)
PoE Power Output
Voltage: 55V DC Power: 60W(Max)
PoE Power Budget 180W
Temperature Opera ng Temperature: 0°C ~ 40 °C (32 °F ~104°F )
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F )
Humidity Opera ng Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing
- 5 -
Fan