Viewpro Z40K User manual

40x 4K Object Tracking Gimbal Camera
Images are for reference only, please subject to the actual product.
Quick Start Guide
Z40K

-1-
!Please make sure that the motor is not stopped by any object during
the rotation, if the gimbal is blocked during rotation, please remove
the obstruction immediately.
Z40K
Z40K Overview
[1] Control box
[2] Gimbal fixed copper cylinder
[3] Damping ball
[4] Upper damping board
[5] Lower damping board
[6] YAW axis motor
[7] Roll axis motor
[8] Pitch axis motor
[9] HD zoom camera
Z40K is a 25.9MP 4K camera with 3-axis gimbal. It's powered by Panaso-
nic 1/2.3” COMS module, has up to 40x optical zoom. The high-end
camera module and advanced pinpoint anti-vibration system bring you
extreme stable high image quality at anytime. Specially designed for long
distance inspections and aerial photography. All parameters are perfectly
set, you just need to install the gimbal camera to UAV, then ready to fly.
[2]
[1]
[3]
[6]
[7]
[8]
[4]
[5]
[9]

-2-
In the Box
Gimbal Camera Dimension
Gimbal camera*1
Copper cylinders*4 Anti shedding buckle*4
Button head hexagon screw*16
5mm*12 8mm*4
Damping board*2
Unit :mm
96
140
153
84
106

-3-
Install the camera as shown
1.Insert SD card
2.connect HDMI to display
SD card position
Control Box position
Connection of Control Box and Wiring Instruction
Instaling
HDMI : micro HDMI OUTPUT
1080P 60fps default
SD card: max 128G，class10
FAT32 or exFAT format
HDMI position
3S~4S
.

-4-
USB
1 2 3
R6208
S B
Fu t ab a
DATA
1
2
3
4
5
6
7
8/B
Digi
t
alServo O n l
y
ForH SM od e
S.B U S
S.bus/Rx
Pitch
Yaw
Mode
Zoom
Focus
Pic/Rec
Multi
Av
Roll/Tx
3. Connect the signal line as below
USB
1 2 3
5V GND
RX1 RX2 RX3
TX1 TX2 TX3
4. Power supply with 12V, red line is positive and black is negative.
PWM
S.bu s/ Rx
.
.
Roll/Tx
Pitch
Yaw
Mode
Zoom
Focus
Pic/Rec
Multi
Av
PWM
S.bu s/ Rx
Roll/Tx
Pitch
Yaw
Mode
Zoom
Focus
Pic/Rec
Multi
Av

-5-
Function Description
Signal functions
PWM in
5V output
GND
TTL 115200/8/1/N
USER BOARD
RX
TX
GND
S.bus/Rx
Roll/Tx
Pitch
Yaw
Mode
Zoom
Focus
Pic/Rec
Multi
Av
S.bus/Rx: connect to Rx2 for track function.
Roll/ Tx: connect to Tx2 for track function.
Pitch: PWM in, pitch control

-6-
1 pitch up
2 pitch stop
3 pitch down
We have protocol for
con t rol the gimb a l
and camera, please
contact our technical
support for detail
doc.
USER BOARD / GPS module
TX
GND
RX
TTL 9600/8/1/N
1 Yaw right
2 Yaw stop
3 Yaw left
Pitch: PWM in, pitch control
Yaw：PWM in, Yaw contro

-7-
1 zoom tele
2 stop zoom
3 zoom wide
1 focus tele
2 stop focus
3 focus near
1
2
3
Position 1: Lowest speed for pitch and yaw.
Position 2: Middle speed for pitch and yaw.
Position 3: Highest speed for pitch and yaw. The speed is continuously quickly
from 1 to 3.
One click: Home position.
Two click: Look down.
Three click: Yaw not followed by frame.
Four click: Yaw followed by frame.
Five click: Restore the factory settings.
(Click = from 2 to 3 and back to 2 quickly)
ZOOM: Zoom the camera Focus: Focus the camera
Mode: Change the speed / home position

-8-
1
2
3
1
2
3
AV: NO AV output.
Pic/ Rec picture / Start record, stop record
Multi: Back up PWM channel for customization
Switch 2 to 1: Camera mode change;
Picture mode: the number is quantity of photos that
SD card can storage;
Record mode: the time is recording time left.
Switch 2 to 3:
A. take a picture
B. Start record / stop record

-9-
Hardware Para me ter
Gimbal Spe c
Came ra Spe c
Working voltage
Input voltage
Output voltage
Dynamic current
Idle current
Power consumption
Output
Local-storage
Control method
Pitch/Tilt
Roll
Yaw/Pan
Vibration angle
One-key to center
Ima ger Sensor Panasonic 1/2.3inch CMOS
Lens
Zoom
Total pix el
Record effective pixel
Picture effective pixel
Optical Image Stabilization
Record format
Record pixel
Record shutter speed(Manual)
Picture format
Picture pixel
Picture shutter speed(Manual)
Dynamic range
Min object distance
Viewing angle
Sync system
Local vide o
HD output
AV output
S/N ratio
Min illumination
Backlight compensation
Gain
White bala nce
Control system
Communication protocol
12V
3S ~ 4S
5V (connect with PWM)
450mA @ 12V
330mA @ 12V
≤5.4W
-40 ~ +60
micro HDMI(HD output 1080P 60fps)
SD card (Up to 128G, class 10, FAT32 or ex FAT format)
PWM / TTL / SBUS
±90°
±85°
±150°
Pitch/Roll: ±0.02°, Yaw ±0.03°
√
F1.8~F3.6(f=4.08~81.6mm)
Optical zoom:20x, iA zoom:25x(4k) / 40x(FHD)
4k:8.29MP / FHD:6.10MP(16:9)
25.9MP(4:3)
5 axis Optical Image Stabilization
MPEG-4
4k:3840*2160/30p FHD:1080/60p (HD:720/30p)
1/30 ~ 1/8000
JPEG
20.4M(4:3
1/2 ~ 1/2000
65dB
1.5M
Horizontal: 53.2°(Wide end) ~ 5.65°(Tele end)
Vertical: 39.8°(wide end) ~ 4.2°(tele end)
Focus: 66.6°(wide end) ~ 7.2°(tele end)
Progressive scanning
1080P 30fps local TF card
1080P/720/480P 60fps HDMI1.4
Standard CVBS 1Vp-p
38dB
Color 0.05lux@F1.6
Backlight compensation/strong light inhibition
Auto
Auto/Manual
UART/IR/PWM
PELCO-D, Hitachi protocol or VISCA
Working environment temp. ℃ ℃
：
25.9MP
）

-10-
Focus
Focus speed
Lens initialization
User pre setting bit
Ima ge rotation
Facial recognition
OSD
Auto/Manual/One-time automatic focus
2s
Built-in
20 sets
180°, Horizontal/Vertical mirror image
√
Not support
630g
153*96*140mm
1pc gimbal camera device, 16pcs screws / Box
2812g
360*300*250mm
Packing Information
N.W.
G.W.
Product meas.
Accessories
Package me as.