ViewSonic VA930-1 VLCDS24020-1W User manual

Service Manual
ViewSonic VA930-1
(VA930-1_SM_584-Rev. 1.0-September 2002)
ViewSonic381 Brea Canyon Road, Walnut, California 91789 USA - [phone]
Model No. VLCDS24020-1W
19” Color TFT LCD Display
3. LOCATION OF CONTROLS

Copyright
Copyright ¤2002 by ViewSonic Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of ViewSonic Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular
purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time
to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or
changes.
Trademarks
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision Date Description Of Changes Approval
1a 9/4/02 Initial Reversion DCN-2433 K.Yang
ViewSonic Corporation iConfidential – Do Not Copy VA930-1
1b11/05/02 Revise DCN-2433 C.Shen

TABLE OF CONTENTS
ViewSonic Corporation ii Confidential – Do Not Copy VA930-1
1. PRECAUTIONS AND NOTICES...............................................................................1
2. SPECIFICATIONS ....................................................................................................2
3. LOCATION OF CONTROLS.....................................................................................3
5. BLOCK DIAGRAM....................................................................................................9
6. TROUBLE SHOOTING FLOW CHART...................................................................11
7. SPARE PARTS LIST...............................................................................................15
8. EXPLODED DIAGRAM AND SPARE PARTS LIST................................................26
9.SCHEMATIC DIAGRAMS........................................................................................28
10.PCB LAYOUT DIAGRAM........................................................................................38
4.ADJUSTING PROCEDURE......................................................................................4

1. PRECAUTIONS AND NOTICES
Prior to using this manual, please ensure that you have carefully followed all the procedures outlined in
the user manual for this product.
Read all of these instructions.
Save these instructions for later use.
Follow all warnings and instructions marked on the product.
Do not use this product near water.
This display should be installed on a solid horizontal base.
When cleaning, use only a neutral detergent cleaner with a soft damp cloth. Do not spray with liquid or
aerosol cleaners.
Do not expose this display to direct sunlight or heat. Hot air may cause damage to the cabinet and other
parts.
Adequate ventilation must be maintained to ensure reliable and continued operation and to protect the
display from overheating. Do not block ventilation slots and openings with objects or install the display
in a place where ventilation may be hindered.
Do not install this display near a motor or transformer where strong magnetism is generated. Images
on the display will become distorted and the color irregular.
Do not allow metal pieces or objects of any kind fall into the display from ventilation holes.
Slots and openings in the cabinet and the back or bottom are provided for ventilation, to ensure reliable
operation of the product and to protect it from overheating, those openings must not be blocked or
covered. Those openings should never be blocked by placing this product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a radiator or heat register. This
product should not be placed in a built-in installation unless proper ventilation is provided.
ViewSonic Corporation 1Confidential – Do Not Copy VA930-1

2. SPECIFICATIONS
1. Specifications
LCD panel type 19.0”TFT(Fujitsu)
Power Consumption 48 W (typ)
Displayable Resolution SXGA 1280 x 1024 maximum
Pixel dimension 0.294 mm x 0.294 mm
Display Color 16.7 M
Viewing Angle
(CR=10)
Horizontal: ±85q
Vertical: ±85q
Response Time 25 ms typ.
Contrast Ratio 500:1 typ.
Brightness 250 cd / m2typ.
Active Display Area 376 mm horizontal x 301mm vertical
AC/DC adapter Input:AC 100~264V,47~63 Hz
Output:+12V DC.
Dimensions ( WxHxD ) 439 mm(W) x 465mm(H) x 180mm(D)
Weight 7.5 kg (unit)
Input connector 15 Pin D-Sub.
Power management YES
Temperature
Operating : 0°C ~ +40°C
Storage : -20°C ~ +60°C
ViewSonic Corporation 2Confidential – Do Not Copy VA930-1

3. LOCATION OF CONTROLS
3. LOCATION OF CONTROLS
ViewSonic Corporation 3Confidential – Do Not Copy VA930-1

The " adjusting procedure" of VA930 model
1. Turn off the display by power button key on the front of bezel,
2. Disconnect the DC power cable from power jack at rear side.
3. Press and hold the “Ÿ” button key on the front of the bezel
4. Connect the power cable with power jack, and keep pressing the “Ÿ” button key.
5. Press the power button key to turn the display on, and then release the “Ÿ” and power button.
6. The unit is set into Reset mode, OSD main window will be shown on the display,
you can see a red message for “ALL RESET” with a red frame inside OSD windows.
7. The LED lightsup with orange and change to green color during reset procedure.
8. OSD changesinto a message for "Auto Image Adjust", it disappearsafter reset procedure.
9. After that the input video signal is showed on display.
4. ADJUSTING PROCEDURE
ViewSonic Corporation 4Confidential – Do Not Copy VA930-1

5.BLOCK DIAGRAM
FROM
A/D ADAPTOR
INTERFACE BOARD(DPWBN5419T8---A)
COMPUTER
GRAPHIC
12V
3.3V
5V
W1
(DB15)
A/D
CONVERTER
AD9883
(U3)
SCALER
SD1210-2
(U8)
DDC
EPROM
24C21A
(U5)
Serial
EEPROM
24C16
(U17)
MPU
(U15)
MTV230P
Serial
EEPROM
24C16
(U9) JP2
TO
INVERTER
JP3 SWITCH MODE
POWER SUPPLY
19” LCD
PANEL
SW BOARD
DPWBN5418T8----
INVERTER
RUNTP5392T8----
CON1
CON4
5CON CON2
CON3
JP7
X1
OSC PLL
U12
AUDIO BOARD
DPWBN5417T8----
ViewSonic Corporation 5Confidential – Do Not Copy VA930-1

YES
NO
ON
OFF
GREEN
Hsync,Vsync
Or DE error
ORANGE
OSD no response
Picture dim
The brightness is
different between upper
and lower side of panel
Picture without color
Vertical, Horizontal
Out of sync
One or more colored
vertical lines
Even (or odd) vertical
line is dark
Does
picture
display
Back-light
On or off?
A
dark picture
full of
colored
vertical lines
Check
power
LED
Check display
resolution Check inverter
Check I/F board JP1
Check LCD cable
Check I/F board JP4
Check LCD panel
J1,J2,J3
Check I/F board
Check SW board S1~S4
Check OSD adjustment
Check inverter
Check backlight
Check signal cable
Check I/F board
Check LCD panel
Check LCD panel
Check I/F board
Check SW board
J1
Check inverter
Check I/F board
RGB signal
error
H,V sync
error
or a picture
6.TROUBLE SHOOTING FLOW CHART
ViewSonic Corporation 6Confidential – Do Not Copy VA930-1

YES
YES
YES
NO
CHECK 5V,3.3VB,
LCD_VCC & 3V3_MCU
START
POWER CKT
(12V,+5V & 3.3V CKT)
POWER CKT
CHECK POWER CKT
END
ViewSonic Corporation 7Confidential – Do Not Copy VA930-1