Viking DNA-510 Instructions for use

P
Pr ra ac ct ti ic ce e
T
TE EL LE EC CO OM MS SO OL LU UT TI IO ON NS SF FO OR RT TH HE E2 21 1S ST TC CE EN NT TU UR RY Y
TECHNICAL
TECHNICAL
DNA-510
DNA-510
Digital Mass
Notification Announcer
June 8, 2012
P
Ph ho on ne e. .. .. .7 71 15 5. .3 38 86 6. .8 88 86 61 1
Power: 120V AC/13.8V AC 1.25A UL listed adapter provided
Dimensions: 133 mm x 91 mm x 44 mm (5.25” x 3.58” x 1.75”)
Weight: 0.8 kg (1.76 lbs)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95%
non-condensing humidity
Sampling Rate: 96K (equivalent)
Connections: (2) RCA audio jacks, 11 position cage clamp ter-
minal strip
Audio output: 600 ohm with volume adjustable potentiometer,
maximum level = 2.2 dBm/ 1V RMS across 600 ohm load
Page Trigger Output: 12V DC (20mA maximum) or N.O./N.C.
relay contacts (1A 30V DC / 0.3A 110V AC maximum)
Add Emergency Mass Notification Messages
and Alert Tones to your Existing Paging System
S
Sp pe ec ci if fi ic ca at ti io on ns s
F
Fe ea at tu ur re es s
• Non-volatile memory - retains programming during
power outage
• Up to 2 minutes of total message record time
• Record up to 5 different emergency messages
• Ten different emergency alert tones:
• Call progress detection for automatic hang up on
CPC, busy signal, dial tone or 20 seconds of silence
(During live page only).
• Separate volume controls for paging, messages and
alert tones
• Automatically interrupts current page or background
music to inject emergency announcement, alert tones
or live page
• Programmable trigger input to activate a message
and/or alert tone
• N.O. & N.C. trigger output contacts for activating
flashing beacon (BLK-3-EWP), Alarm Dialer
(K-202-DVA), etc.
• Access code to prevent fraudulent use
• Connects directly to an unused line input (trunk) or
station port of a phone system or to a dedicated
phone line
The DNA-510 is a digital mass notification announcer, capable of
providing up to 2 minutes of digitally recorded voice emergency
instructions and alert tones over your existing paging system.
The DNA-510 connects to a phone line, analog phone system
station or a phone system’s unused trunk/line input allowing you
to securely page, trigger emergency messages and/or alert
tones and program the unit from any remote touch tone phone.
When activated, the DNA-510 will interrupt any current paging or
background music and inject an emergency voice message
and/or alert tone over your paging system. A live page can also
be announced.
The DNA-510 can be programmed to repeat one up to 2 minute message, two up to 1 minute messages,
three up to 40 second messages, four up to 30 second messages or five up to 24 second messages. It
can also be programmed with 10 different alert tones for emergency mass notification of: evacuation, lock
down, severe weather, fire, bomb threat, hazardous material release, tornado, flash flood, terrorist alert,
all-clear, etc.
Provide Emergency Mass Notification for:
• Schools
• College Campuses
• Restaurants
• Churches
• Theaters
• Auditoriums
• Dormitories
• Office buildings
• Factories
• Any “areas of assembly”
A
Ap pp pl li ic ca at ti io on ns s
1. Hi/Low Siren
2. Code 3 Temporal (ANSI
S3.41) Slow Whoop
3. Attack Wail*
4. Alert Siren*
5. Fast Wail*
6. Fast Whoop
7. March Time Horn
8. Bell*
9. Buzzer
10. All Clear Tone
*Note: Looping recordings of actual
emergency sirens and alarm bell.

IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT [phone]
Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please:
1. Know the model number, the serial number and what software version you have (see serial label).
2. Have your Technical Practice in front of you.
3. It is best if you are on site.
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The
customer MUST be able to step through recommended tests for diagnosis.
2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.
3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.
RETURNING PRODUCT FOR REPAIR
The following procedure is for equipment that needs repair:
1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)
number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individual-
ly boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:
Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.
4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
F
Fe ea at tu ur re es sO Ov ve er rv vi ie ew w
the necessary modifications to maintain uninterrupted service.
If trouble is experienced with the DNA-510, for repair or warranty information, please contact:
Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI 54016 [phone]
If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service com-
mission or corporation commission for information.
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:
Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak
hours, such as early morning or late evenings.
It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is connected. This
is to avoid damaging the equipment caused by local lightning strikes and other electrical surges.
PART 15 LIMITATIONS
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
FCC REQUIREMENTS
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the side of this
equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If
requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN's on a
telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of
the REN's should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as deter-
mined by the total REN's, contact the local telephone company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected
to the telephone line, ensure the installation of this DNA-510 does not disable your alarm equipment. If you have ques-
tions about what will disable alarm equipment, consult your telephone company or a qualified installer.
If the DNA-510 causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the cus-
tomer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is nec-
essary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make
Message Volume Control - To adjust audio output
level of recorded messages and pre-recorded alert
tones (attack wail, alert siren, fast wail, bell)
Power Indicator LED
Mode Switch - Set to "Ring Trip" when connect-
ing to a phone system's unused station port or
dedicated phone line. Set to "Trunk" when
connecting to a phone system's unused line
(trunk) input port.
Page Active LED
Dip Switches - See Programming section F.
JP5 Trigger Output Selection - See
Programming section K.
11: Optional Earth Ground (see **Note, pg 3)
Page Trigger Output (see Programming, K)
10: N.C. Relay Contact
9: + 12VDC / COM Relay Contact
8: - Neg / N.O. Relay Contact
6 & 7: Trigger Input - Can be configured as
normally open, normally closed or disabled.
Momentary or continuous contact.
4 & 5: Phone Line Input - Connect to a ded-
icated phone line or phone system's unused
analog station port or unused line (trunk) input.
See "Mode Switch" above.
Audio Loop Output 1 - Line level output to paging amplifier
(RCA type connector, also available on screw terminals
2 & 3 "Audio Out 2".
Alert Tone Volume Control - To adjust audio output level of synthesized alert
tones (hi/low, code 3 whoop, fast whoop, march time horn, buzzer, all clear)
1 & 2: Optional Message Record Input - Connect to output of tape player,
PC sound card, etc. to record professional messages or unique alert tones.
Note: This is optional, normal recording is done via telephone.
2 & 3: Audio Loop Out 2 - Same as Audio Loop Out 1 but uses screw
terminal connections. See Audio Loop Out 1 (above).
1234567891011
GROUND
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
DIGITAL MASS
NOTIFICATION ANNOUNCER
POWER 13.8V AC
MODEL DNA-510
PAGING
VOLUME
MESSAGE
VOLUME
MIN MAX MIN MAX
AUDIO
IN
AUDIO
OUT 1
ALERT
TONE
VOLUME
REC INPUT
1
AUDIO
OUT 2
23
LINE
INPUT
45
TRIGGER
INPUT
6789
EARTH GND
10 11
TRIGGER OUTPUT
N.O.
COM
N.C.
Paging Volume Control - To adjust audio
output level of "live" paging. Note: This does not
control the paging volume from your phone system's
p
aging port.
Power Input - Connect to provided 13.8V AC
1.25A adapter.
Audio Loop Input - Line level pre-amp input for
non-emergency paging, background music etc.
(RCA type connector)
2
LIMITED WARRANTY
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manu-
factured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others. This warranty does not cover
non-EWP products that have been exposed to wet or corrosive environments.
NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FIT-
NESS FOR ANY PARTICULAR PURPOSE.
EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAM-
AGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.
EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL
BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.
IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLU-
SIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED
AS SUCH.

I
In ns st ta al ll la at ti io on na an nd dA Ap pp pl li ic ca at ti io on ns s
3
Dedicated (POTS)
Phone Line
Up to (15) 8 Ohm Speakers
(Viking Model 25AE
shown, not included)
C
LED5
C
LED3
C
LED4
C
LED2
C
LED1
123
on
4
30 WATT TELECOM
PAGING AMPLIFIER
VIKING©MODEL PA-30
PWR 15 VAC
123456
SPKRS SPKRS
600 OHM OUTPUT
789101112
AUX IN PAGE IN
PAGE CONTACT
13 14 15 16 17
LINE IN CONTACT CLOSURE
BACKGROUND MUSIC IN
NIGHT TRANSFER
VIKING
ELECTRONICS
HUDSON, WI 54016
MASTER
VOLUME
MIN MAX
LOUD RINGING
70V OUT
+ SPKR - + SPKR -
70V OUT
600 OHM
OUTPUT AUX IN PAGE IN PAGE
CONTACT
RINGING
LINE CC NT
Optional Background Music
Source (not included)
or
Page Audio Out
Phone System's
Unused Phone
Line Input
(Trunk Port) or
Unused Analog
Station Port
*13.8V AC
Adapter
(included)
*UPS
120V AC
*See caution below
To External Trigger (Example: Fire Alarm
Control Panel Trigger Relay Output)
**Earth Ground (optional)
Up to (15) more 8 Ohm Speakers
(Viking Model 30AE shown, not included)
Audio out to
additional PA-30's
(Connect multiple
PA-30's to drive
additional speakers.
See the PA-30
Technical Practice)
123
on
4
Set all PA-30 Dip
Switches to OFF
3.5mm
plug
Mode Switch
(see Note above)
Ring
Trip Trunk
Model PA-30 (not included)
Page Trigger Output
Selection (J5 Jumper)
1 2 3 4
= Dry Contact
Optional Page Trigger Contact
12345678 91011
GROUND
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
DIGITAL MASS
NOTIFICATION ANNOUNCER
POWER 13.8V AC
MODEL DNA-510
PAGING
VOLUME
MESSAGE
VOLUME
MIN MAX MIN MAX
AUDIO
IN
AUDIO
OUT 1
ALERT
TONE
VOLUME
REC INPUT
1
AUDIO
OUT 2
23
LINE
INPUT
45
TRIGGER
INPUT
6789
EARTH GND
10 11
TRIGGER OUTPUT
N.O.
COM
N.C.
This application will allow you to control the DNA-510 from any telephone on your phone system. You can simply access the phone
system’s line the DNA-510 is connected to or call the phone system extension or dedicated POTS line it is connected to. The unit
will automatically answer allowing you to enter a touch tone command to interrupt standard paging or background music and
announce a live emergency page, start a emergency pre-recorded message or start one of ten different alert tones. Note: Place
mode switch in “Trunk” position when connecting to a phone system’s unused line input. Place mode switch in “Ring Trip” position
when connecting to a phone system’s unused station port or dedicated phone line.
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the telephone line.
It is recommended that a surge protector be installed to protect against such surges.
!
A. Connecting to a Phone Systems Unused Line (Trunk) Input, Unused Analog Station Port or
to a Dedicated (POTS) Line
This application will allow you to control the DNA-510 from one or more dedicated (standard analog) telephones. You can simply
come off-hook with any phone and enter a touch tone command to interrupt standard paging or background music and announce
a live emergency page, start a emergency pre-recorded message or start one of ten different alert tones. Note: Place the mode
switch in the “Trunk” position.
B. Connecting to One or More Dedicated Telephones
* Caution: Uninterrupted Power Supply (UPS) recommended.
UPS should have sufficient backup time to allow for emer-
gency communication during a power outage. Maximum power
consumption: DNA-510: 10 watts, PA-30: 50 watts.
Dedicated Telephones
12345678 91011
GROUND
*13.8V AC
Adapter
(included)
*UPS
120V AC
To External Trigger (Example: Fire Alarm
Control Panel Trigger Relay Output)
**Earth Ground
(optional)
Paging Amplifier
(not included)
SPKR
Out
+ -
SPKR
Out
+ -
Paging
Input
Page
Trigger
Input
Background
Music Input
Mode Switch
(see Note above)
Trunk
*UPS
120V AC
Page Trigger Output
Selection (J5 Jumper)
1 2 3 4
OR
= Dry Contact
= 12VDC
1 2 3 4
Pin 9: +
Pin 8: -
*** To control optional strobe light
(Example: Viking model BLK-3-EWP)
120V AC
- or -
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
DIGITAL MASS
NOTIFICATION ANNOUNCER
POWER 13.8V AC
MODEL DNA-510
PAGING
VOLUME
MESSAGE
VOLUME
MIN MAX MIN MAX
AUDIO
IN
AUDIO
OUT 1
ALERT
TONE
VOLUME
REC INPUT
1
AUDIO
OUT 2
23
LINE
INPUT
45
TRIGGER
INPUT
6789
EARTH GND
10 11
TRIGGER OUTPUT
N.O.
COM
N.C.
** Note: To increase surge protection, fas-
ten a wire from the screw terminal to Earth
Ground (grounding rod, water pipe, etc.)
** Note: To increase surge protection, fasten a wire from the screw terminal to Earth Ground (grounding rod, water pipe, etc.)
* Caution: Uninterrupted Power
Supply (UPS) recommended. UPS
should have sufficient backup time
to allow for emergency communica-
tion during a power outage.
Maximum power consumption:
DNA-510: 10 watts.
*** Note: A 390-750 Ohm 1/2 Watt resistor
(not included) is required for this application.
For more information, see DOD# 880.

4
B. Security Code
A. Accessing the Programming Mode
1. Accessing the Programming Mode Locally (Trunk Mode) with a Security Code
Step 1. Come off-hook with any phone connected to terminals 4& 5 PHONE LINE INPUT, 1 or 2 beeps will be heard.
Step 2. Enter Qfollowed by the 6-digit security code (factory set to 845464, see Programming section B).
Step 3. A double beep will indicate that you have accessed the programming mode.
Step 4. You can now touch tone program the features listed in section L.
Step 5. When finished programming, hang up.
2. Accessing the Programming Mode Locally (Trunk Mode) without a Security Code
P
Pr ro og gr ra am mm mi in ng g
3. Accessing the Programming Mode Remotely (Ring Trip Mode)
Step 1. Move DIP switch 1 from OFF to ON (Security Code Bypass mode, see DIP Switch Programming section G).
Step 2. Come off-hook with any phone connected to terminals 4& 5 PHONE LINE INPUT.
Step 3. A double beep will indicate that you have accessed the programming mode.
Step 4. You can now touch tone program the features listed in section L.
Step 5. When finished programming, hang up and move DIP switch 1 back to the OFF position.
Step 1. Call into the DNA-510 from a touch tone phone.
Step 2. The DNA-510 will automatically answer and provide 1 or 2 beeps.
Step 3. Enter Qfollowed by the 6-digit security code (factory set to 845464, see Programming section B).
Step 4. A double beep will indicate that you have accessed the programming mode.
Step 5. You can now touch tone program the features listed in section L.
Step 6. When finished programming, dial ##7, 3 beeps should be heard, then hang up.
Note: Programming from a cell phone may not be suitable in areas with weak coverage.
This six-digit number can be used to access the programming mode. The security code has been factory set to 845464 (V-I-K-I-N-
G). It is recommended that you change the security code to a personal six-digit number. To change the security code, access pro-
gramming (see Programming section A). Enter six digits 0-9 followed by #47. If you have forgotten your security code, follow the
steps in Programming section A, 2. Accessing the Programming Mode Locally (Trunk Mode) without a Security Code. Note:
The security code must be 6-digits and can NOT contain a
Q or #.
C. Access Code
This is a programmable number that must be entered to access the DNA-510’s touch tone operation commands. The access code
can be programmed from 1-6 digits and is factory disabled. An access code is useful at installations where only select personnel
are allowed to control the DNA-510. To program an access code, access programming (see Programming section A) then enter
a 1-6 digit number followed by #48. With an access code programmed, as soon as you call the line the DNA-510 is connected to
(ring trip mode) or access the phone system’s line input the unit is connected to (trunk mode), you will hear one beep signaling you
to enter your 1-6 digit access code. If an incorrect access code is entered, the unit will output 3 beeps and you can re-enter your
access code. When a correct access code is detected, 2 beeps will be heard and you can now operate the unit. Note: The access
code must be 1-6 digits and can NOT contain a
Q or #.
D. Recording Messages
Recording of the voice messages may be done either locally or remotely with a touch tone phone. Once programming has been
entered, touch tones are used to start and stop the recording process. To start a recording: enter Qfollowed by the message
number (1-5). The DNA-510 gives a single beep to indicated that it is recording and then starts the recording process. Speak
into the handset of the telephone to record the message. The DNA-510 has a total message record time of 2 minutes allowing
for (1) up to 2-minute recording, (2) up to 1-minute recordings, (3) up to 40-second recordings, (4) up to 30-second recordings
or (5) up to 24-second recordings. When finished recording the message, enter any touch tone to stop the recording process.
At this point the DNA-510 automatically plays back the message just recorded. If the recording process goes over 2-minutes,
the DNA-510 stops the recording and starts to playback the message. To clear a single message: enter Q#followed by the num-
ber of the input (1-5).
1. Recording Messages from Your Touch Tone Phone
Pre-recorded emergency messages and/or alert tones can be recorded through the DNA-510’s “REC INPUT”. Connect a line
level (2V p-p max) source across terminals 1 and 2. Use a touch tone phone to start, stop and review recordings (see para-
graph 1 above). Recording audio can be monitored through your phone’s earpiece. Make several sample recordings at differ-
ent volume settings from your audio source. Review the sample message audio quality to select correct source volume setting.
Note: Use caution not to speak into the handset during external source recording as unit can record telephone line audio during recording.
2. Recording Messages from an External Source (Tape player, CD, PC wav/mp3, etc.)
CAUTION! Attention Installers: All programming must be thoroughly tested when installation is complete.
Periodic testing at regularly scheduled intervals is recommended.
Note: The unit must be idle (alert tones and messages stopped) to access programming.

E. Playing Back Messages
When in programming, enter Q0 followed by the message number (1-5) to playback the selected message. If a message has been
cleared, 3 beeps will be heard.
5
F. DIP Switch Programming
DIP Switches shown
in the factory default
positions
ON
OFF 1 2
ON
12345678 91011
GROUND
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
DIGITAL MASS
NOTIFICATION ANNOUNCER
POWER 13.8V AC
MODEL DNA-510
PAGING
VOLUME
MESSAGE
VOLUME
MIN MAX MIN MAX
AUDIO
IN
AUDIO
OUT 1
ALERT
TONE
VOLUME
REC INPUT
1
AUDIO
OUT 2
23
LINE
INPUT
45
TRIGGER
INPUT
6789
EARTH GND
10 11
TRIGGER OUTPUT
N.O.
COM
N.C.
Switch
1
1
2
2
Position
OFF
ON
OFF
ON
Description
Normal Operation Mode (factory setting)
Security Code Bypass Mode (for local programming)
* Trigger Input Sensitivity Reduced
Trigger Input Sensitivity Normal (factory setting)
* Note: Very long wire runs on the trigger input can cause false trig-
gers. If this occurs, lower the trigger input sensitivity by placing dip
switch 2 in the OFF position.
G. Message Repeat Counter
Each recorded message can be programmed to repeat 1-99 times or repeat indefinitely until manually stopped via touch tone com-
mand or trigger input control. Once programming has been entered, enter a 2-digit repeat count number 00-99 (00 = infinite) fol-
lowed by the memory location #11-#15 (messages 1-5 respectively). Once a message has been triggered, the DNA-510 will repeat
that message (and pre-alert tone if programmed) until it has reached the programmed repeat count. A repeating message can also
be stopped with a touch tone “#“ operation command or by opening a contact closure or second momentary closure when activat-
ed from the “trigger input” (see section J. Trigger Input below).
H. Message Pre-Alert Tone
Each recorded message can be programmed to have one of ten different pre-alert tones (see chart below). Each pre-alert tone will
be approximately 8 seconds in length and will sound prior to playing the emergency message. Once programming has been
entered, enter a single digit 0-9 followed by memory location #21-#25 which correspond to message 1-5 respectively. To disable a
pre-alert tone simply enter the memory location only.
Blank = Disabled
00 = Hi/Low
01 = Code 3 Whoop
02 = Attack Wail
03 = Alert Siren
04 = Fast Wail
05 = Fast Whoop
06 = March Time Horn
07 = Bell
08 = Buzzer
09 = All Clear Tone
10 = (not used)
11 = Message 1 and Pre-Alert Tone (if programmed)
12 = Message 2 and Pre-Alert Tone (if programmed)
13 = Message 3 and Pre-Alert Tone (if programmed)
14 = Message 4 and Pre-Alert Tone (if programmed)
15 = Message 5 and Pre-Alert Tone (if programmed)
I. Programmable Touch Tone Operation Commands
Each touch tone operation command 1-9 can be programmed with an alert tone, emergency message or emergency message with
a pre-alert tone (see chart below). When a touch tone is entered during operation, the DNA-510 will start playing the specific alert
tone or message that has been programmed for that touch tone command. Once the programming has been entered, enter 2-dig-
its followed by memory location #31-#39 which correspond to touch tone digits 1-9 respectively. To disable a touch tone operation
command, simply enter the memory location only. Note: Touch tone “0” can not be programmed and is factory set to “live page”.
J. Trigger Input
The DNA-510 has a single remote trigger input (available on terminals 6 and 7) that can be activated by a momentary or continu-
ous normally open or normally closed contact. When the input senses a contact, the unit will start a pre-programmed alert tone,
emergency message or emergency message with a pre-alert tone. The input sensitivity can be reduced (see DIP Switch
Programming section F). The trigger input is factory set to play a repeating “code 3 Temporal Slow Whoop” from a momentary NO
contact and can be stopped from a second momentary contact or by a touch tone “#“ command. To program the input see
Programming section L Quick Programming Features on page 6. Note: When programmed to activate from a continuous con-
tact, and the repeat counter is programmed to infinite (00), the unit will continue to repeat the programmed alert tone and/or mes-
sage until the contact is released or the DNA-510 is stopped from a touch tone “#“ command. Alternatively, if the repeat counter is
programmed from 1-99, the message will repeat until it reaches its pre-programmed repeat count or the continuous contact has
released.
Blank = Disabled (default)
0 = 8 seconds of Hi/Low
1 = 8 seconds of Code 3 Whoop
2 = 8 seconds of Attack Wail
3 = 8 seconds of Alert Siren
4 = 8 seconds of Fast Wail
5 = 8 seconds of Fast Whoop
6 = 8 seconds of March Time Horn
7 = 8 seconds of Bell
8 = 8 seconds of Buzzer
9 = 8 seconds of All Clear Tone
Note: All alert tones continuously repeat until manually stopped with a “#“ command. Messages repeat per programmed repeat
counter. Example: To program touch tone “1” to play message 4 enter 14#31.
K. Page Trigger Output (J5)
The DNA-510 is factory set to output 12VDC (20mA maximum) on terminals 8 and 9 dur-
ing paging, messages or alert tones. Remove both jumpers and reconnect one jumper
across pins 2 and 3 to change page trigger output to a N.O./N.C. dry relay contact (1A
30V DC / 0.3A 110V AC maximum).
Page Trigger Output Selection (J5 Jumper)
OR
Dry N.O./N.C.
Contacts
12VDC (20mA
maximum)
1 2 3 41 2 3 4

6
Security code (default = 845464) ...........................................................................................................
Access code (default = blank/disabled) .................................................................................................
Message memory (see chart 1 below, default: five 24-second messages) ............................................
Record messages 1-5 (press any digit to stop recording) ......................................................................
Playback messages 1-5 (press any digit to stop message playback) ....................................................
Clear messages 1-5 ...............................................................................................................................
Message 1 repeat counter (00-99, 00 = infinite, default = 00) ................................................................
Message 2 repeat counter (00-99, 00 = infinite, default = 00) ................................................................
Message 3 repeat counter (00-99, 00 = infinite, default = 00) ................................................................
Message 4 repeat counter (00-99, 00 = infinite, default = 00) ................................................................
Message 5 repeat counter (00-99, 00 = infinite, default = 00) ................................................................
Message 1 pre-alert tone (see chart 2, default = blank/disabled) ...........................................................
Message 2 pre-alert tone (see chart 2, default = blank/disabled) ...........................................................
Message 3 pre-alert tone (see chart 2, default = blank/disabled) ...........................................................
Message 4 pre-alert tone (see chart 2, default = blank/disabled) ...........................................................
Message 5 pre-alert tone (see chart 2, default = blank/disabled) ...........................................................
Touch tone “1” operation command (message or alert tone - see chart 3, default = Code 3 Whoop) ...
Touch tone “2” operation command (message or alert tone - see chart 3, default = Attack Wail) ...........
Touch tone “3” operation command (message or alert tone - see chart 3, default = Alert Siren) ............
Touch tone “4” operation command (message or alert tone - see chart 3, default = Fast Wail) ..............
Touch tone “5” operation command (message or alert tone - see chart 3, default = Fast Whoop) ..........
Touch tone “6” operation command (message or alert tone - see chart 3, default = March Time) ..........
Touch tone “7” operation command (message or alert tone - see chart 3, default = Bell) .......................
Touch tone “8” operation command (message or alert tone - see chart 3, default = Buzzer) ..................
Touch tone “9” operation command (message or alert tone - see chart 3, default = All Clear) ................
Note: Touch tone “0” is not programmable and is factory set to “live page”.
Trigger input (see chart 4 below) ............................................................................................................
Forced hang-up .....................................................................................................................................
Reset all programming to factory default settings ..................................................................................
Blank = Disabled
00 = Hi/Low
01 = Code 3 Whoop
02 = Attack Wail
03 = Alert Siren
04 = Fast Wail
05 = Fast Whoop
06 = March Time Horn
07 = Bell
08 = Buzzer
09 = All Clear Tone
10 = (not used)
11 = Message 1 and Pre-Alert Tone (if programmed)
12 = Message 2 and Pre-Alert Tone (if programmed)
13 = Message 3 and Pre-Alert Tone (if programmed)
14 = Message 4 and Pre-Alert Tone (if programmed)
15 = Message 5 and Pre-Alert Tone (if programmed)
Blank = Disabled (default)
0 = 8 seconds of Hi/Low
1 = 8 seconds of Code 3 Whoop
2 = 8 seconds of Attack Wail
3 = 8 seconds of Alert Siren
4 = 8 seconds of Fast Wail
5 = 8 seconds of Fast Whoop
6 = 8 seconds of March Time Horn
7 = 8 seconds of Bell
8 = 8 seconds of Buzzer
9 = 8 seconds of All Clear Tone
1= (1) up to 2-minute message
2 = (2) up to 1-minute messages
3 = (3) up to 40-second messages
4 = (4) up to 30-second messages
5 = (5) up to 24-second messages
First Digit: 0 = N.O. contact (default), 1 = N.C. contact, 2 = Disabled
Second Digit: 0 = Momentary contact (default), 1 = Continuous contact
Third and Fourth Digits:
Note: All alert tones continuously repeat until manually stopped with a “#“ command. Messages repeat per programmed repeat count-
er. Example: To program touch tone “1” to play message 4, enter: 14 #31.
Note: When trigger input is set to continuous and the message repeat counter is set to infinite, the message (and pre-alert tone if
programmed) will repeat until contact is removed.
L. Quick Programming Features
6 digits (0-9)
1-6 digits (0-9)
1 digit (1-5)
Q1 - Q5
Q01 - Q05
Q#1 - Q#5
2 digits (0-9)
2 digits (0-9)
2 digits (0-9)
2 digits (0-9)
2 digits (0-9)
1 digit (0-9)
1 digit (0-9)
1 digit (0-9)
1 digit (0-9)
1 digit (0-9)
2 digits (00-15)
2 digits (00-15)
2 digits (00-15)
2 digits (00-15)
2 digits (00-15)
2 digits (00-15)
2 digits (00-15)
2 digits (00-15)
2 digits (00-15)
4 digits
##7
###
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
#47
#48
#49
#11
#12
#13
#14
#15
#21
#22
#23
#24
#25
#31
#32
#33
#34
#35
#36
#37
#38
#39
#40
Enter Digits +
Memory
Location
Chart 1: Message Memory (Caution: Changing this parameter erases all previously recorded messages.)
Chart 2: Pre-Alert Tone
Chart 3: Programmable Touch Tone Operation Commands
Chart 4: Trigger Input
00 = Hi/Low
01 = Code 3 Whoop (default)
02 = Attack Wail
03 = Alert Siren
04 = Fast Wail
05 = Fast Whoop
06 = March Time Horn
07 = Bell
08 = Buzzer
09 = All Clear Tone
10 = (not used)
11 = Message 1 and Pre-Alert Tone (if programmed)
12 = Message 2 and Pre-Alert Tone (if programmed)
13 = Message 3 and Pre-Alert Tone (if programmed)
14 = Message 4 and Pre-Alert Tone (if programmed)
15 = Message 5 and Pre-Alert Tone (if programmed)

O
Op pe er ra at ti io on n
To control the DNA-510 simply call the telephone line, phone system station port or access the phone system’s line input (trunk) the unit
is connected to. At this point you should hear one or two beeps. Two beeps will indicate the access code has been disabled and you can
now operate the unit. A single beep will signal you to enter your pre-programmed access code (1-6 digits), when a correct access code
is detected, two beeps will be heard and you can now operate the unit. Three beeps indicate an incorrect code. Once in the operation
mode you can enter a touch tone command which will allow you to start a live page or start and stop any of the pre-programmed alert
tones and/or message (see chart below). Note: If you have accessed the DNA-510 remotely (ring trip mode), you will be allowed up to
20 seconds between touch tone command entries. If more than 20 seconds has elapsed, the DNA-510 will automatically hang up.
Description
Live Page (default, not programmable)
Play programmed Message and/or Alert Tone (default = Code 3 Whoop)
Play programmed Message and/or Alert Tone (default = Attack Wail)
Play programmed Message and/or Alert Tone (default = Alert Siren)
Play programmed Message and/or Alert Tone (default = Fast Wail)
Play programmed Message and/or Alert Tone (default = Fast Whoop)
Play programmed Message and/or Alert Tone (default = March Time Horn)
Play programmed Message and/or Alert Tone (default = Bell)
Play programmed Message and/or Alert Tone (default = Buzzer)
Play programmed Message and/or Alert Tone (default = All Clear Tone)
Stop any message, alert tone or live page (default, not programmable)
Dial
0
1
2
3
4
5
6
7
8
9
#
Description
633Hz/457Hz alternating every 800msec.
0.5 sec sweep from 200Hz-700Hz, pause 0.5 sec, repeat 3 times then pause for 1.5 sec and repeat
total cadence. Cadence complies with ANSI S3.41.
Air raid siren recording: 2 second rise to 5 seconds of steady siren then decay for 5 seconds, repeat.
Loop every 13 seconds.
Severe weather siren recording: 2 second rise to steady siren. Loop steady siren every 11 seconds.
Siren recording: 1.5 second rise and decay, repeat. Loop every 8 seconds.
Fast repeating up sweep: 600Hz-1200Hz with 1 second rise, repeat.
Fast on/off horn: 639Hz/1087Hz 0.25 sec on, 0.25sec off, repeat.
Alarm system bell recording: Loop every 8 seconds.
120Hz/240Hz, steady.
1KHz steady tone.
Alert Tone
Hi/Low Siren
Code 3 Temporal Slow
Whoop (ANSI S3.41)
*Attack Wail
*Alert Siren
*Fast Wail
Fast Whoop
March Time Horn
*Bell
Buzzer
All Clear Tone
7
A. Pre-Programmed Alert Tones and/or Messages
B. Alert Tone Descriptions
C. Programming Chart
To help simplify programming, write all of the programming numbers below. See section F. Quick Programming Features page 5.
Security Code: ____ ____ ____ ____ ____ ____ + #47
Access Code: ____ ____ ____ ____ ____ ____ + #48
Message memory: ____ + #49
Message 1 repeat counter: ____ ____ + #11
Message 2 repeat counter: ____ ____ + #12
Message 3 repeat counter: ____ ____ + #13
Message 4 repeat counter: ____ ____ + #14
Message 5 repeat counter: ____ ____ + #15
Message 1 pre-alert tone: ____ + #21
Message 2 pre-alert tone: ____ + #22
Message 3 pre-alert tone: ____ + #23
Message 4 pre-alert tone: ____ + #24
Message 5 pre-alert tone: ____ + #25
Touch tone “1” operation command: ____ ____ + #31
Touch tone “2” operation command: ____ ____ + #32
Touch tone “3” operation command: ____ ____ + #33
Touch tone “4” operation command: ____ ____ + #34
Touch tone “5” operation command: ____ ____ + #35
Touch tone “6” operation command: ____ ____ + #36
Touch tone “7” operation command: ____ ____ + #37
Touch tone “8” operation command: ____ ____ + #38
Touch tone “9” operation command: ____ ____ + #39
Trigger input: ____ ____ ____ ____ + #40
* Note: Looping recordings of actual emergency sirens and alarm bell.

8
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
DOD# 492 Printed in the U.S.A.
P
Pr ro od du uc ct tS Su up pp po or rt tL Li in ne e. .. .. .7 71 15 5. .3 38 86 6. .8 86 66 66 6F Fa ax xB Ba ac ck kL Li in ne e. .. .. .7 71 15 5. .3 38 86 6. .4 43 34 45 5
ZF302540 Rev B
D. User Recorded Message Script Examples
E. Operation Commands
Use the chart to the right to fill in the number to be dialed
or line to access. Access Code (if programmed) and all
pre-programmed operation commands. Make photo-
copies of the chart and place near each phone that may
use the DNA-510.
Emergency Notification System
Operation Commands
Viking Model DNA-510
Dial: _____________________________________
Enter Access Code: _______________________
Enter a digit to activate the following:
0 _________________________________
1 _________________________________
2 _________________________________
3 _________________________________
4 __________________________________
5 __________________________________
6 __________________________________
7 __________________________________
8 __________________________________
9 __________________________________
# _________________________________
Live Page
Stop Message, Alert Tone or Page
The following are some examples of messages which may be recorded in the field:
“May I have your attention please. May I have your attention please. The signal you have just heard indicates a report of a fire in this building. Please proceed
to the nearest exit and leave the building. Do not use the elevators. Do not re-enter the building unless directed to do so by the proper authorities.”
“May I have your attention please. May I have your attention please. A fire emergency has been reported in the building. A fire emergency has been reported
in the building. Please proceed to the stairways and exit the building. Do not use the elevators, but proceed to the stairways and exit the building.”
“May I have your attention please. May I have your attention please. A fire emergency has been reported on your floor. A fire emergency has been reported on
your floor. Please proceed to the stairways and exit the building. Do not use the elevators.”
“May I have your attention please. May I have your attention please. An emergency condition exists in this building. An emergency condition exists in this build-
ing. Please proceed to the stairways and exit the building. Do not use the elevators.”
“May I have your attention please. May I have your attention please. An armed intruder is in the building. Lock all doors and take cover.”
“Your attention please. A severe weather warning has been received. Please walk to the nearest safe area and wait for further instructions. Elevator lobbies,
stairwells, bathrooms and auditoriums are designated safe areas in the event of severe weather. Stay away from windows and glass. Do not use the elevators.”
“May I have your attention please. May I have your attention please. A tornado warning has been issued for this area. A tornado warning has been issued for
this area. Please take all appropriate safety actions at this time.”
“May I have your attention please. May I have your attention please. A hurricane warning has been issued for this area. A hurricane warning has been issued
for this area. Please take all appropriate safety actions at this time.”
“Attention chemical release. Stay inside buildings and close windows and doors unless advised by authorities to evacuate the area. Attention chemical release.
Stay inside buildings and close windows and doors unless advised by authorities to evacuate the area. Chemical release.”
“May I have your attention please. This is a test of the emergency warning system. This is only a test. This is a test of the emergency warning system. This is
only a test.”
“Attention. Your attention please. The building emergency condition has been cleared. You may return to your normal activities. The building emergency has
been cleared. You may return to your normal activities.”
Fire 1
Fire 2
Fire 3
Emergency
Condition
Lockdown
Severe
Weather
Tornado
Hurricane
Chemical
Release
Test
All Clear