Viotek GN32LD User manual

ORCURVED GAMING MONIT
USER MANUAL
GN32LD

3
Table of Contents
Section 1: Safety Precautions................................................................4
Section 2: Box Contents.........................................................................5
Section 3: Product Overview .................................................................6
3.1 – Monitor Buttons .........................................................................6
3.2 – Monitor Ports.............................................................................6
Section 4: Stand Installation..................................................................7
Section 5: Wall Mounting........................................................................9
Section 6: Connectivity Options ...........................................................10
6.1 – Connecting the Power Cable.....................................................10
6.2 – Connecting Your Earphones .....................................................10
6.3 – DP Connectivity ........................................................................11
6.4 – HDMI Connectivity ....................................................................11
6.5 – DVI Connectivity .......................................................................11
Section 7: Basic Operation ....................................................................12
Section 8: Indicator Light .......................................................................13
Section 9: OSD Setup .............................................................................14
9.1 – OSD Menu Functions ................................................................15
Section 10: Troubleshooting..................................................................17
10.1 – PIP (Picture in Picture) Input Information ................................18
10.2 – PBP (Picture by Picture) Resolution Information.....................18
Section 11: Specifications......................................................................19
11.1 – Resolution Compatibility for DVI/DP ........................................19
Section 12: 1 Year Limited Hardware Warranty ...................................20

4
Section 1: Safety Precautions
Read and observe the following warnings and information below.
1. Before cleaning, always unplug your monitor. It is recommended that you use dry cloth or
lightly damp cloth to clean your monitor. Dry cloth is, however, the safest. If using damp
cloth, wait for your monitor to completely dry before plugging it in again.
2. Do not use alcohol or ammonia-based cleaner and/or liquids to clean your monitor.
3. This monitor features ventilation openings on the back of the unit. Avoid blocking these
openings to prevent the monitor from overheating.
4. Avoid placing this monitor near any heat sources e.g: portable heaters or heating vents,
as this may cause damage to your monitor.
5. Do not spray cleaner and or any kind of liquid directly onto the monitor’s screen or any
part of the monitor.
6. Do not insert anything into any part of the monitor especially the ventilation openings.
7. Always make sure your monitor is placed on a secure, level surface to prevent it from
falling and sustaining damage.
8. Unplug your monitor during any extended periods of non-use.
9. Do not place heavy items on the monitor or monitor cables.
10. Do not attempt to disassemble or remove parts from the monitor. Any disassembly or
modication etc. not performed by an authorized technician can result in damage to the
monitor and/or possible exposure to high voltage electricity which may lead to serious
injury or death.
VIOTEK shall not be held responsible for injury or damage of products or persons due to
failure to adhere to the aforementioned precautions or any others noted hereafter.

5
Section 2: Box Contents
Monitor x 1 Stand Stem x 1
(with attached bracket)
Stand Base x 1 Cover Base x 1
Cover x 1
Power Cable x 1
(AC 100-240V, 50/60Hz)
NO. 2 Screws x 3 NO. 3 Screws x 4
(for Wall Mounting)
NO. 1 Screw x 1 DP Cable x 1
Screwdriver x 1 Allen Key x 1 User Manual x 1
Note: The NO. 3 Screws come in two sizes: 26mm x 2 and 31mm x 2.
26mm
31mm

6
Section 3: Product Overview
3.1 – Monitor Buttons
8 Audio Output:Insert the audio cable for output of audio signals.
9 DP Connector: Insert one end of the DP cable into the computer’s DP output and
connect the other end to the monitor’s DP port.
10 HDMI Connector: Insert one end of the HDMI cable into the computer’s HDMI output
and connect the other end to the monitor’s HDMI port.
11 DVI Connector: Insert one end of the DVI cable into the computer’s DVI output and
connect the other end to the monitor’s DVI port.
8 9 10 11
1 3 4 5 6 72
1 Power Connector: Insert the Power Cable to supply power to the monitor.
2 M Menu Button: Press to display the OSD menu or enter sub-menus.
3 Down Button: Press to move down in the menus.
4 Up Button: Press to move up in the menus.
5 E Exit Button:Press to exit.
6 Power Button: Press to turn the monitor on/off.
7 LED Indicator: Changes colors to indicate status. Refer to Section 8.
The E button can also be used to switch between two color gamuts when a compatible
graphics card and either HDMI or DP connections are in use.
3.2 – Monitor Ports

7
Section 4: Stand Installation
Keep the foam over the monitor before attaching the Stand. Follow the steps below to
nish the installation.
1. Open the package, take out the product with foam still attached, and gently place it on a
desktop or table.
Monitor
Stand Base
Foam
Foam
Stand Stem
2. Take out the two parts of the stand and use the included allen key and the NO. 1 screw to
attach them.
Use only the NO.1 screw provided.
Stand Base
Stand Stem
NO. 1 Screw (1x)
Bracket
3. Take out the Cover Base, insert it into the stand near the base and secure it with three
NO. 2 Screws. Next, place the Cover over the Cover Base and press lightly to secure.
Use only the NO. 2 screws provided.
NO. 2 Screws (3x)
Cover
Cover Base
4. Take out the Monitor and remove the foam.

8
5. Align the Stand Stem’s bracket with the opening on the back of the monitor. Carefully
insert the bracket into the opening, top rst then bottom. The pieces should click into
place.
6. Place the Monitor on your desktop or table after completing the installation and carefully
pull or push it up or down to adjust the height.
Stand Stem
7. Press the button to, and remove the Monitor from the bracket and to easily unmount it.
Button
To avoid damaging the screen, don’t press down on the screen while placing it on
the desktop or table.

9
Section 5: Wall Mounting
1. Open the package, take out the product with foam still attached, and gently place it on a
desktop or table. If the monitor was attached to the stand, remove the stand.
Monitor
Stand Base
Foam
Foam
Stand Stem
2. Remove the original screws x 4 ( 1) from the opening in the back of the monitor, and then
use the NO. 3 Screws provided to secure the rear panel.
- Do not discard the original screws. They are needed to secure the rear panel for
the stand installation. Refer to Section 4.
- Use only the NO. 3 Screws (31 mm x 2 pcs, 26mm x 2 pcs) provided. You MUST
follow the gure below to nish the installation.
Use the 31mm
NO. 3 Screws x 2
Use the 26mm
NO. 3 Screws x 2
3. Follow the directions received with your mounting base (not included) and install the
monitor on the wall.
Mounting Base
(Not included)
1

10
Section 6: Connectivity Options
6.1 – Connecting the Power Cable
• Connect the included Power Cable to the power connector, and then plug the other end
into an AC outlet.
Power Cable (Supplied)
6.2 – Connecting Your Earphones
• When earphones are plugged in, no sound will be emitted from the speakers.
Earphones (Not included)
Listening to loud audio for prolonged periods of time may permanently damage your
hearing.