Vip-Vision INTKIT-A1 User manual

INTKIT-A1
Analogue 4-Wire Video Intercom
Quick Start Guide
INT-A1-Q10121

VIP Vision INTKIT-A1 Intercom Installation Manual - Version: INT-A1-Q10121
2
1. Introduction
2. Included Components
Thank you for purchasing this Intercom System. This install guide
covers basic setup and installation for your intercom system.
For detailed technical support and software downloads, visit our
Help Centre at: help.c5k.info
help.c5k.info
IMPORTANT:
• Door Stations are designed to mounted in a sheltered location,
not exposed directly to weather.
• When installing the Door Station, apply outdoor silicone sealant
between the Door Station and the wall, and seal the hole that
has been created for the cable to prevent water ingress. If using
a mounting box, ensure the box is also sealed, and the included
waterproof rubber seals are used when installing the screws.

3
Visit help.c5k.info for more information and support
3. Mounting Guide
1.
3.
5.
7.
4.
6.
2.

VIP Vision INTKIT-A1 Intercom Installation Manual - Version: INT-A1-Q10121
4
4. Front Panel
Button Description
• Press to hang up the incoming call without answering.
• Press to adjust monitor settings.
• In set up mode, press to decrease value.
• Press to answer incoming calls. Press again to hang up.
• In set up mode, press to increase value.
• Press to cycle between video live views of Door Station 1,
Door Station 2, Camera 1 and Camera 2.
• In set up mode, press to skip to next item.
• Press to unlock the door where the door station(VTO) calls.
• In set up mode, press to exit set up menu.
Button Description
Call • Press once to call door monitor(s)
Indoor Monitor
Door Station

5
Visit help.c5k.info for more information and support
5. Back Panel
Name Description
Power
PWR 12VDC positive input
G 12VDC negative input
Camera Ports
CAM Analogue camera signal input
G Analogue camera signal ground
Door Station Ports
P1, P3 12VDC positive output to door station
V1, V3 Video signal
A1, A3 Audio signal
G Common ground for door stations
Indoor Monitor Ports
P2, P4 12VDC positive input to monitors
V2, V4 Video signal
A2, A4 Audio signal
G Common ground for monitors

VIP Vision INTKIT-A1 Intercom Installation Manual - Version: INT-A1-Q10121
6
6. Wiring
7. Wiring Example - One Door Station and One Indoor Monitor
Port connection rules
• Port A of the indoor monitor can be
connected to Port C of another indoor
monitor.
• Port B of the indoor monitor can be
connected to Port D of another indoor
monitor.
• Port A of the indoor monitor cannot be
connected to Port B or D of another indoor
monitor.
• Port C of the indoor monitor cannot be
connected to Port B or D of another indoor
monitor.

7
Visit help.c5k.info for more information and support
8. Wiring Example - Three Door Stations and One Indoor Monitor

VIP Vision INTKIT-A1 Intercom Installation Manual - Version: INT-A1-Q10121
8
9. Two Door Stations and Three Indoor Monitors

9
Visit help.c5k.info for more information and support
10. Setup Menu
Button Description
• Open the menu
• Wake up the monitor
• Decrease Vol (volume), Bright (brightness), Contrast and
BellVol (bell volume), change Bell tone and turn off DND
(do not disturb)
• Increase Vol (volume), Bright (brightness), Contrast and
BellVol (bell volume), change Bell tone and turn off DND
(do not disturb)
• Select an item to adjust or change
• Exit the menu and lock the screen

All products, designs and software may be subject to change without prior written notice. Information, layout and
graphics presented in this guide are the property of their respective owners.
See www.c5k.info for more information.
For detailed technical support and software downloads,
visit our Help Centre at: help.c5k.info
help.c5k.info