VirtuaPin Plunger Kit User manual

VirtuaPin™PlungerKit
InstallaonGuide
ThingsYou’llNeed
TOOLS
Screwgun / Drill (corded or baery powered)
Screwdriver
FASTENERS
2 ‐ #4 1/2” pan head screws (oponal)
3 ‐ 10‐32 Machine Screws
3 ‐ 1/4” Washers
Please read all warnings and follow all operang procedures of all equipment used
in the installaon of this product.

PlungerKitParts
When you receive your kit,
please take a moment to ensure
you’ve received all of the
components found in the illustra‐
on on the le.
To wire the buons to your
kit, a terminal barrier strip, like
the one below, is strongly
suggested.
1
Setup
For opmal results, mount the
board on the boom of your cabi‐
net face‐up and oriented as pic‐
tured on the right. The J1 and J2
headers should be facing the cabi‐
net and the USB connectors on
the le side of the cabinet. Con‐
nect the plunger to the connector
indicated to the right.
IMPORTANT!
Plunger MUST be connected
before the board is powered on.
2
Note: If using screws to fasten the board to your cabinet’s boom, be sure to drill
pilot holes, DO NOT over ghten and damage the board!


Wiring
(Pins are numbered le to right)

Plug the cable into the connector pictured above in Diagram2, and then into your PC. The controller will auto‐
macally be detected, and the drivers installed.
The accelerometer (nudging) is auto‐calibrated on power on. To calibrate the plunger, simply pull it all the way
back, hold for 2 seconds, and release.
J1(10‐Pin)Connector
PIN
1
2
3
4
5
6
7
8
9
10
BUTTON
Digital Plunger
Right Flipper
Not Used
Common/Ground
Right Magnasave
Change Camera*
Toggle HUD*
Look at Backbox*
Pause
Exit Table
Joy
1
2
—
—
3
4
5
6
7
8
J2(8‐Pin)Connector
PIN
1
2
3
4
5
6
7
8

BUTTON
Start Game
Le Flipper
Le Magnasave
Insert Coin 1
Insert Coin 2
Test*
Service*
Ground
Joy
9
10
11
12
13
14
15
—
COLOR
Green
Red
—
Black
White
Purple
Orange
Blue
Gray
Yellow
COLOR
Green
Red
White
Yellow
Purple
Brown
Blue
Black
*UsedwithFuturePinball
USBandCalibraon
90DayLimitedManufacturer’sWarranty
The VirtuaPin Digital Plunger Kit, sold by VirtuaPin Cabinets, is covered by a 90‐day Limited Manufacturer’s Warranty. Any and all claims
must be brought to the aenon of VirtuaPin Cabinets to receive warranty service. Remember to retain a copy of your receipt to receive
warranty service during the warranty period.
Tamperingwith,oralteringinanyway,theVirtuaPinDigitalPlungerKitwill immediatelyvoidthiswarranty.In addion,warranty
requestsdeterminedtobetheresultofabuseorimproperusagewillbedenied.
The manufacturer warrants the VirtuaPin Digital Plunger Kit against defects in materials and workmanship as follows:
Labor ‐ For a period of 90 days from receipt, if the manufacturer determines the equipment is defecve, subject to the limitaons of this
warranty, the manufacturer will replace defecve components, at no charge. The manufacturer warrants any such work against defects for
the remainder of the original warranty period.
Parts ‐ For a period of 90 days from receipt, the manufacturer will supply, at no charge, new or remanufactured parts in exchange for
parts determined to be defecve, subject to the limitaons of the warranty. The manufacturer warrants any such parts against defects for
the remainder of the original warranty period.



USBandCalibraon
SengUpVisualPinball
SengUpFuturePinball