VIRTUFIT Ultimate Pro 2 User manual

Ultimate Pro 2 Ergometer Rowing Machine
EN
T+31 (0)74-7600219
Eservice@tnessbenelux.nl
Wwww.tnessbenelux.nl
Twekkelerweg 263
7553 LZ Hengelo
Nederland
Fitness
Benelux
Uw partner in fitness
For any questions regarding the product you can contact Fitness Benelux:

2Ultimate Pro 2 Ergometer
Rowing Machine
EN
Safety Instructions 3
Assembly Parts 4
Note 5
Assembly Steps 6-11
Part Overview 12
Part List 13-14
CONTENTS

3Ultimate Pro 2 Ergometer
Rowing Machine
EN
SAFETY INSTRUCTION
ASSEMBLY PREPARATION
To ensure ease of product assembly, please take time to verify the size and quantities of all required assembly hardware.
Use the itemized parts listing and hardware chart for reference.
The product assembly process has been documented in easy to follow steps. Please read all assembly instructions
carefully. Take time to review the manual and familiarize yourself with the entire assembly process before proceeding.
Assembly Tip: It is always helpful to pre-stage the items needed for each assembly step.
Perform product assembly in a 4-ft. x 10-ft. flat area. Note: After assembly is completed, allow a minimal 2-3 feet of
space on each side of rower for user access and dismounting.
Do not dispose of any packaging materials until assembly of the product is completed.
Assembly tools are included, but you may also use standard household tools to complete assembly of this product.
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of injury, please read the following precautions before assembling or using your new product.
1. It is the responsibility of the owner to ensure that all users of this equipment are adequately informed of stated precautions .
2. Read all instructions and enclosed literature carefully. Understand the assembly and operation before using the equipment.
3. Use equipment on a flat level surface. Use adjustment levelers on the bottom of equipment to help stabilize unit.
4. It’s recommended to place an exercise mat beneath the equipment for added protection of floors or carpets.
5. Keep children and pets away from equipment at all times.
6. Inspect product on a frequent basis. Tighten loose assemblies or hardware as needed. Replace worn or damaged parts.
7. This equipment is intended for indoor use only. Use in non-recommended environment can lead to serious injury and will
void all related warranties and liabilities.
8. Recommended user weight should not exceed 500 pounds.
9. Keep equipment clean and properly maintained.
10. Observe and adhere to all warning labels posted on equipment.
11. Properly warm up and stretch before starting any strength training or cardio exercise routine.
12. If you feel pain or dizziness at any time while exercising, stop immediately and consult your physician.
SAFETY WARNING: Before starting an exercise program, consult your physician. This is especially important for individuals over
the age of 35 or persons with pre-existing health problems. It’s important to read all instructions carefully. We assume no responsibility
for personal injury or consequential damages sustained by or through the use of this equipment. Additional terms and conditions are
listed in the back of this manual or enclosed owner’s manual.
Colors and specications subject to change without notice.

4Ultimate Pro 2 Ergometer
Rowing Machine
EN
(J0)M8 Nylon Nut
(J5)Bol M8x25mm (J6)Bolt M8x16mm (J7)Washer M8x1.5t (J8)Pull pin (J9)Screw
M4x10mm
(J1)Bolt M10x16mm (J2)Washer M10x1.5t (J3)Bolt M6x50mm
(J4)Screw
M4x12.7mm
ASSEMBLY PARTS
K
E
C
A
G
F
H
D
B

5Ultimate Pro 2 Ergometer
Rowing Machine
EN
NOTE
NOTE: Before assembly please lay out ALL pieces accordingly to ensure you
are not missing any items.
PLEASE BE CAUTIOUS as some components may be sharp and can cause harm if not
handled correctly. Always use safety measurements when assembling any piece of
equipment or machinery.

6Ultimate Pro 2 Ergometer
Rowing Machine
EN
For best results place Forward Base (A) (Damper
Fan) upside down on a soft and secure surface.
Once this is done, the pre- screwed holes for
Forward Base Leg (C) will be visible. To bolt in
Forward Base Leg (C) into Forward Base (A), place
directly on top of pre-screwed holes. Secure with 2
(J1) Bolt(s) and (J2) Washer(s).
STEP 1
2-1 Please LIGHTLY pull wires so that they do not
recede into the stem of Base Leg (A). DO NOT
CUT WIRES; wires will connect to console tube
when installing console.
CAUTION: PLEASE HANDLE WITH CARE,
AS ELECTRICAL WIRES ARE DELICATE. IF
WIRES ARE HANDLED TOO AGGRESSIVELY
THEY WILL DISLOCATE.
Once the wires are exposed,
CAREFULLY connect wires.
STEP 2
2.2
2.1
2-2 Once wires are connected CAREFULLY
secure Console Tube (G) to the stem of Base
Leg (A).
PLEASE BE CAREFUL OF EXPOSED WIRE
ENDS. THE WIRES SHOULD RECEDE BACK
INTO STEM ONCE CONNECTED IN
ORDER TO PREVENT DAMAGE OR
DISLOCATION.
ASSEMBLY STEPS

7Ultimate Pro 2 Ergometer
Rowing Machine
EN
To nish securing Console (G) onto Forward
Base (A) please attach Place Holder (H).
Place Holder (H) will break up into
2 components (H1) and (H2).
These components will rejoin together once
attached onto forward Base (A).
Once rejoined please secure with
2 screws (J9) and 1 screw(J4).
To install Rear Base Leg (D), face Base
Railing (B) face down so that the receiving
device for the seat cushion is
on the floor. Place Rear Base Leg (D) above
the pre-screwed holes of the Base Rail (B).
Once placed secure with 2 (J1) Bolt(s) and
(J2) washer(s).
STEP 3
J9
J9
STEP 4
D
ASSEMBLY STEPS
B

8Ultimate Pro 2 Ergometer
Rowing Machine
EN
To install foot pedals (E1) and (E2) into (A) Forward Base join the together by Steel Bracket (K). Steel Bracket (K) should
slide into place of Foot Pedal (E1). Once placed secure with 2 (J5) bolts and 2 (J0) nuts.
NOTE: You must install foot pedals before moving forward with the assembly process. Should Step 5 be skipped the
Pre-screwed holes on the base railing would cover up the pre screwed holes on the Forward Base leg where the foot
pedals are to be installed.
J0
J5
E2
A
K
E1
STEP 5
ASSEMBLY STEPS

9Ultimate Pro 2 Ergometer
Rowing Machine
EN
To install Seating place Seat Cushion (F) above
the pre-screwed holes of Base Railing (B)
The high angled read end of Seat Cushion (F)
should face the back end of Base Railing (B).
Secure with 4 Bolts (J6) and 4 washers (J7).
To install Pull pin (J8) locate
the pre-screwed bolt at the end
of Forward Base (A) and turn
clockwise until the bolt is
securely fastened
Align Forward Base (A) with Base
Railing (B) until the pre-screwed holes
are aligned with one another. Secure
Forward Base (A) to Base Railing (B)
with 4 Bolts (J6) and 4 Washers (J7).
NOTE: Please be sure to tighten and
secure ALL BOLTS AND WASHERS
IN THEIR PLACE TO ENSURE A
SOLID AND SECURE foundation to
the rower.
STEP 6
F
J7
J7
B
J8
A
J6
J6
ASSEMBLY STEPS

10 Ultimate Pro 2 Ergometer
Rowing Machine
EN
Rower Storage
To fold the VirtuFit Ultimate Pro 2 Ergometer Rowing Machine, simply pull the PULL PIN (J8) while holding the Rail Handle
(B21) located between Forward Base (A) and Base Railing (B). Gently set Forward Base (A) down to ground by controlling
Rail Handle (B21) gently downwards. This will cause Forward Base (A) to drop down and will allow you to raise Base Railing
(B) until it clicks securely into a folded position. When you are ready to unfold the VirtuFit Ultimate Pro 2 Ergometer Rowing
Machine again, simply pull on PULL PIN (J8) while holding onto Base Railing (B). Gently set Base Railing (B) onto ground,
then use Rail Handle (B21) to pull upwards until rower clicks into unfolded position.
NOTE: Please use a rm grip on ALL MOVING PARTS when folding the VirtuFit Ultimate Pro 2 Ergometer
Rowing Machine. The weight of the rower will cause Forward Base (A) to drop aggressively when folding and will
cause Base Railing (B) to drop aggressively when unfolding.
STEP 7
J8
B
B21
ASSEMBLY STEPS

11 Ultimate Pro 2 Ergometer
Rowing Machine
EN
Damper Lever
Foot Height Adjuster
Push down to adjust the position of the heel support.
ASSEMBLY STEPS

12 Ultimate Pro 2 Ergometer
Rowing Machine
EN
PART OVERVIEW

13 Ultimate Pro 2 Ergometer
Rowing Machine
EN
NO. NAME SPECIFICATION QTY NO. NAME SPECIFICATION QTY
A1 Main Frame Assembly 1 A21 Sensor Base Cover ABS 1
A2 Flywheel Fan Assembly 1 A22 Tapping Screw M4*12mm 5
A2-1 Fan 1 A23 Sensor Cover ABS 1
A2-2 Tube 1 A24 Outer Chain Cover ABS 1
A2-3 One-Way Bearing FC 2016 1 A25 Handle-Bar Φ31.8 1
A2-4 Iron Washer S20 1 A26 1/4” Chain 1
A2-5 S-type Buckle M5*10mm 2 A27 Chain Connecting Spacer SC-2473 2
A2-6 Cap head Socket Screw 4 A28 Evan Head Socket Screw M8*20mm 2
A2-7 Axial of flywheel Φ20*197mm 1A29 Chain Hook 3
A2-8 Magnet Covering Φ100*Φ60*15T 1 A30 Chain Connector 1
A2-9 Ring Magnet BR-6004ZZDKFL 1 A31 T-type Nut 10
A2-10 Bearing Old Design 2 A32 Hand Grip 4
A2-11 Interval Ring M4*12mm 1 A33 End Cap 4
A2-12 Tapping Screw 3 A34 Axial of Pulley(Front) Φ10*79.8mm 1
A2-13 1/4” Chain Gear 1 A35 C-Type Buckle 2
A2-14 PU Washer Φ430*2.5T 2 A36 Pulley 2
A2-15 Fan Stable Bracket M4*10mm 1 A37 Philip Head Socket Screw M5*10mm 1
A2-16 Tapping Screw R42 8 A38 Main Frame Front Cap ABS 1
A2-17 R-type Buckle ABS 2 A39 Axial of Pulley(Back) Φ10*79.8mm 2
A3 Chain Cover (left) 1 A40 Elastic Rope Bracket 2
A4 Mesh ABS 1 A41 Chain Bracket 1
A5 Chain Cover (right) ABS 1 A42 Pulley Socket 1
A6 Adjust Disc M4*8mm 1 A43 Chain Pulley 2
A7 Tapping Screw 2 A44 Hexagon Head Screw M6*10mm 2
A8 Variable Resistor M4*12mm 1 A45 Trim Panel 2
A9 Tapping Screw R40 21 A46 Hexagon Head Screw M6*30mm 2
A10 C-Type Buckle Φ22*Φ44.2*3T 22 A47 Main Frame Bottom
Board(Front)
2
A11 Washer 2 A48 Main Frame Bottom
Board(Back) 1
A12-1 RubberCover 6001 1 A49 Axial of Pin Φ12.7*76mm 1
A12-2 RubberCover 6903 1 A50 Spring 1
A13-1 Bearing 6001ZZDKFL 1 A51 Nut 1
A13-2 Bearing 6903ZZDKFL 1 A52 PlugBlock 1
A14 Nylon Insert Lock Nut M10 1 A53 Foot Pad 1
A15 RingCover ABS 1 A54 Washer M4*Φ10*1T 2
A16 SensorBracket 1 A55 Tapping Screw M4*10mm 2
A17 Sensor 1 A56 Swivel Axial 1
A18 Hearth Rate Reciever 1 A57 Swivel Axial Socket Φ21.5*12mm 2
A19 Handle Holder ABS 1 A58 Washer 1/2”*2.0T*Φ23 2
A20 Philip Head Socket Screw M5*10mm 4 A59 Cap Head Socket
Screw
M10*16mm 2
PART LIST

14 Ultimate Pro 2 Ergometer
Rowing Machine
EN
NO. NAME SPECIFICATION QTY NO. NAME SPECIFICATION QTY
A60 Chain Connecting Axial 1 E1 Left Pedal Rest 1
A61 Elastic Rope 1 E2 Right Pedal rest 1
A62 Axial of Moving Wheel Φ8X156mm 1 E3 Adjust Pedal PAd TPE 2
E4 Left Pedal Rest cover 1
B1 Aluminum Rail 1 E5 Right Pedal Rest cover 1
B2 Seat Carriage Roller 2 E6 Tapping Screw M4*8mm 8
B3 Seat Carriage Cover 2 E7 Set Piece 2
B4 Seat Carriage Wheel 4 E8 Set Base 2
B5 Bearing PR-608ZZ(BMC) 8 E9 Foot Snap 2
B6 Spacer Φ8*Φ12*2mm 8 E10 Flat Head Philips screw M5*15mm 4
B7 Seat Carriage Axial Φ10*121mm 2 E11 Flat Head Philips screw M4*15mm 2
B8 Washer M8*2.0T*Φ16 4 E12 Spacer 2
B9 Lower Acorn Nut M8 4 E13 Nylon Insert Lock Nut M4 2
B10 Seat Carriage Roller 2 E14 Foot Strap 2
B11 Bearing PR-608ZZ(BMC) 2
B12 Even Head Socket Screw M8*20mm 2 F Seat 1
B13 Washer M8*Φ16*2T 2
B14 Lower Acorn Nut M8 2 G1 Console Tube 1
B15 Rail Upper Plate 1 G2 Console Bracket 1
B16 Cap Head Socket Screw M6*10mm 2 G3 Console Back Cover Old Design 1
B17 Rail End Cap ABS 1 G4 Cap Head Socket Screw m8*85mm 1
B18 Philip Head Socket Screw M5*10mm 4 G5 Nylon Acorn Nut M8 1
B19 Double Head Screw Φ5.25*85mm 1 G6 Console 1
B20 Seat Carriage Stopper TPR 2 G7 Ball Head Screw M5*10mm 4
B21 Rail Handle 1
H1 Left Console Tube Cover ABS 1
C1 Front Stabilizer 1 H2 Right Console Tube Cover ABS 1
C2 Flat Oval Cap 40*80 2 J0 Nylon Insert Lock Nut M8 2
C3 Moving Wheel Φ50 4 J1 Cap Head Socket Screw M10*16mm 4
C4 Philip Head Socket Screw M8*40mm 2 J2 Washer M10*1.5T*Φ20 4
C5 Lower Acorn Nut M8 4 J3 Cap Head Socket Screw M6*50mm 4
C6 Foot Pad 40*32mm 2 J4 Tapping Screw M4*12mm 3
C7 Trapping Screw M4*12mm 2 J5 Cap Head Socket Screw M8*35mm 2
J6 Cap Head Socket Screw M8*16mm 10
D1 Rear Stabilizer 1 J7 Washer M8*Φ16*1.5T 10
D2 Flat Oval End Cap 40*80 2J8 Pull pin 1
D3 Foot Pad 40*32mm 2 J9 Ball Head View M4*10mm 2
D4 Tapping Screw M4*12mm 2 K Pedal Stable Bucket 1
PART LIST

T+31 (0)74-7600219
Eservice@tnessbenelux.nl
Wwww.tnessbenelux.nl
Twekkelerweg 263
7553 LZ Hengelo
Nederland
Fitness
Benelux
Uw partner in fitness
Voor vragen of ontbrekende onderdelen kunt u contact opnemen met Fitness Benelux: