Vision TECHCONNECT TC-HDMIW30 User manual

1
TC-HDMIW30_manual_en.doc
TECHCONNECT TC-HDMIW30
OWNERS MANUAL
www.visionaudiovisual.com/techconnect/tc-hdmiw30/

2
TC-HDMIW30_manual_en.doc
DECLARATION OF CONFORMITY
Where applicable Vision products are certified and comply with all known local regulations to a
‘CB Certification’ standard. Vision commits to ensure all products are fully compliant with all
applicable certification standards for sale in the EU and other participating countries.
The product described in this owner manual is in compliance with RoHS (EU directive
2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. This product should be returned
to the place of purchase at the end of its useful life for recycling.
WARNINGS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle, is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
All products are designed and imported into the EU by ‘Vision’ who is wholly owned by ‘Azlan
Logistics Ltd.’, Registered in England Nr. 04625566 at Lion House, 4 Pioneer Business Park,
Clifton Moor, York, YO30 4GH. WEEE Registration: GD0046SY
DECLARATION OF ORIGIN
All Vision products are made in the People’s Republic of China (PRC).

3
TC-HDMIW30_manual_en.doc
USE ONLY DOMESTIC AC OUTLETS
Connecting the unit to an outlet supplying a higher voltage may create a fire hazard.
HANDLE THE POWER CORD WITH CARE
Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself.
Pulling the cord may damage it. If you do not intend to use your unit for any considerable
length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and
try to avoid dropping heavy objects on it. Do not tie a knot in the power cord. Not only could
the cord be damaged, but a short circuit could also be caused with a consequent fire hazard.
PLACE OF INSTALLATION
Avoid installing this product under the following conditions:
• Moist or humid places
• Places exposed to direct sunlight or close to heating equipment
• Extremely cold locations
• Places subject to excessive vibration or dust
• Poorly ventilated places
Do not expose this product to dripping or splashing. DO NOT PLACE OBJECTS FILLED WITH
LIQUIDS ON OR NEAR THIS PRODUCT!
MOVING THE UNIT
Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect
the interconnection cords with other units.
WARNING SIGNS
If you detect an abnormal smell or smoke, turn this product off immediately and unplug the
power cord. Contact your reseller or Vision.
PACKAGING
Save all packing material. It is essential for shipping in the event the unit ever needs repair.
IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE,
DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY.

4
TC-HDMIW30_manual_en.doc
SPECIAL WARNINGS
Never use this product near an aircraft or medical facility. It can cause interference.
Use of product in the following locations may result in abnormal video and audio output:
•Product installed in the walls made of concrete
•Product situated near refrigerator. Microwave oven, or other metal items
•A cluttered room where the wireless signals may be blocked
This product has been tested and manufactured to comply with each country‟s safety rules,
however there is no guarantee that interference will not occur in some scenarios. If
interference happens, adjust distance between transmitter and receiver. Optimal range
between transmitter and receiver is between 2 and 7 meters line of sight.
This product may interfere 5GHz wireless devices. If interference occurs configure your
5GHz router to 2.4 GHz band only.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio
frequency energy and may in extreme cases cause harmful interference to radio
communications. If this happens the user should try:
•Relocating the receiving antenna
•Increasing the separation between the equipment and receiver
•Connect the equipment to a different power circuit.
RADIATION EXPOSURE STATEMENT:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.

5
TC-HDMIW30_manual_en.doc
TRANSMITTER (“Tx”)
1. HDMI input
2. IR Output (IR blaster plugs in here, allows source remote control to be used at distant
display)
3. BLUE Power indicator
4. Micro-USB Power 5V2A (10w minimum)
5. RED Data transmitter indicator
a. slow flashing = performing handshake
b. fast flashing = transmitting data
c. on all the time = error
RECEIVER (“Rx”)
1. Phoenix connector power input
2. GREEN Link indicator
a. solid = good connection with Tx
b. off = poor or no connection with Tx
3. RED Data transmitter indicator
a. slow flashing = performing handshake
b. fast flashing = transmitting data
c. on all the time = error
4. HDMI output
5. IR Input (IR receiver plugs in here)
1
2
3
1
2
3
5
4
4
5

6
TC-HDMIW30_manual_en.doc
INSTALLATION NOTES
1. NORMALLY POWER FROM HDMI WILL BE SUCCICIENT TO POWER TX
The Tx needs 500-1000 milli-amps (mA) to operate. Laptops are only obliged to provide
55mA through the HDMI port but they often provide more.
2. IF NOT USE USB CABLE TO GET SUPPLEMENTARY POWER FROM A USB PORT
Use USB cable provided. It WILL NOT work with cheap USB cables
3. IF THAT’S STILL NOT ENOUGH AN EXTERNAL POWER SUPPLY IS INCLUDED.
DISPLAY SLEEP
The Rx will stop outputting HDMI if no source is present for 10 minutes. This allows the display
to go to sleep when the source is off.
FREQUENCY SPECTRUM
This product uses 5GHz WIFI channels so it can be affected by outside interference in the same
way as any wifi device.
IR PASSBACK
If using a source device which has a remote control, this product allows the remote to be
pointed at the display in the remote location. The IR signal is relayed from the Rx to the Tx to
the source device.
To make this happen the IR blaster and receiver cables mush be used.
•The diode on the blaster must be as close as possible to the source IR receiver.
•The diode on the receiver must be in line-of-sight of the remote control.

7
TC-HDMIW30_manual_en.doc
NOT WORKING?
1. Check USB cable powering Tx. Cheap USB cables will not provide enough power.
2. The computer is set to duplicate or extend the desktop (Control Panel\Appearance and
Personalisation\Display\Screen Resolution)
3. Try other cables between the source and Tx
4. EDID handshakes and HDCP key authentication can create HDMI issues. Try rebooting all
equipment to reset.
5. Check the wifi spectrum with a tool such as https://inssider.en.softonic.com/

8
TC-HDMIW30_manual_en.doc
SPECIFICATIONS
TRANSMITTER DIMENSIONS: 87 x 40 x 17 mm / 3.4″ x 1.6″ x .67″ (length x width x height)
RECEIVER DIMENSIONS: 97 x 79 x 21 mm / 3.8″ x 3.1″ x 0.8″ (length x width x height)
PACKAGED DIMENSIONS: 200 x 150 x 80 mm / 7.9″ x 5.9″ x 3.1″ (length x width x height)
PRODUCT WEIGHT:
Tx: 300 g / 0.06 lbs
Rx: 220 g / 0.49 lbs
PACKAGED WEIGHT: 650 g / 1.43 lbs
CONSTRUCTION MATERIAL: Tx Plastic / Rx Metal
COLOUR: White
TECHNICAL DETAILS:
Maximum Video Format Supported: 1920×1080 / 1080P @ 60Hz
Compression: H.264
Video: HDMI 1.3 with HDCP 1.2
Max transfer rate: 10.2 Gbps
TMDS Signal: 0.7~1.5Vp p
DDC Signal: 5Vp p
Audio: Stereo
IR Passback: 20-60KHz
Max Input and Output cable length: up to 5m (16.4 feet)
Electrostatic Protection: Contact and air discharge level 3 IEC 61000-4-2
Operating Temperature Range: 0-40°C
Operating Humidity Range: < 80 % RH (no condensation)
MTBF (Mean Time Between Failures): > 30,000 hours
Transmitter Power Consumption: 3 watts
Receiver Power Consumption: 5 watts
Latency: < 20 ms
Maximum distance: 30 m (98 feet)
Encryption: 128 bit AES
TRANSMITTER CONNECTIVITY:
1 x HDMI socket – gold-plated input
1 x DC power – Micro USB-B for supplementary power if required
1 x 3.5mm Minijack socket – for IR blaster
RECEIVER CONNECTIVITY:
1 x HDMI (type A) output
1 x DC Power – phoenix connector
1 x 3.5mm Minijack socket – for IR receiver
POWER SUPPLY: 100-240v AC 50/60Hz 5 volt / 2 amp 10 watt. USB-A socket. DC tail length:
1.8 m / 5.9 ft
Transformer integrated into plug. Includes interchangeable plugs: UK/EU/US/AU. Transformer
dimensions: 66 x 43 x 32 mm / 2.6″ x 1.7″ x 1.3″

9
TC-HDMIW30_manual_en.doc
ACCESSORIES INCLUDED:
Power for Tx:
1 x USB-A to Micro -USB-B cable, white, length: 450 mm / 18″
1 x USB-A to Micro -USB-B cable, white, length: 130 mm / 5.1″
Source Connectivity:
1 x HDMI cable, white, length: 130 mm / 5.1″
1 x Mini DP to HDMI cable, white, length: 200 mm /7.9″
IR Connectivity:
1 x IR Blaster cable, black, length: 1 m / 3.3 ft
1 x IR Receiver cable, black, length: 1 m / 3.3 ft
WARRANTY: Lifetime return-to-base
2 years onsite (UK only)
COMPLIANCES: RoHS, WEEE, CE/Tx, CE/Rx, CAC/Tx, CAC/Rx, FCC/Tx, FCC/Rx, RCM-POC, RCM-
SDOC
ORDER PART CODE: TC-HDMIW30 [SAP: 4360679]

10
TC-HDMIW30_manual_en.doc
LIFETIME RETURN-TO-BASE WARRANTY
This product comes with a lifetime return to base warranty. If you have a problem you are
required to provide a DETAILED DESCRIPTION of the fault.
Some Vision products are very technical and require troubleshooting all elements of the
installation as it may not be the Vision product at fault. Because of this the manufacturer may
refuse to replace the item if an adequate description is not provided.
•This warranty applies only to the original purchaser and is not transferable.
•This warranty protects you against the following:
oFailure of any components, including the power supply.
oDamage when the product is first removed from its packaging if reported within
24 hours of purchase.
•If the product is DOA (dead on arrival), you have 21 days from purchase date to notify the
national distributor via your AV reseller.
•The original purchaser is responsible for shipment of the product to the Vision’s appointed
service centre.
•The liability of Vision is limited to the cost of replacement of the faulty unit under warranty
except for death or injury (EU85/374/EEC).
•If the product is end of line (EOL) the Vision will provide a credit instead of replacement.
•This warranty does not protect this product against faults caused by abuse, misuse,
incorrect installation, unstable or faulty power input, or modification.
Vision aims to send a replacement item within 5 working days however this may not always be
possible, in which case it will be sent as soon as practicably possible. UK End users and resellers
can request support at http://www.visionaudiovisual.com/support
2-YEAR ONSITE WARRANTY (UK ONLY)
The manufacturer provides an onsite warranty for the first two years taken from date of sale.
This service can be requested at the url above and is provided at the manufacturer’s discretion.
•This service is only provided for products which are difficult for an end user to get at
and replace.
•The manufacturer will not provide the onsite service if
oThe reseller or end user has been abusive
oThe user has is taking unfair advantage of this service
•The manufacturer will pre-qualify the visit to ensure the fault relates to the Vision
product.
The engineer visits are timed to ensure you are onsite and the room is accessible. A revisit
WILL NOT be provided if access to the room is not provided at the arranged time. Engineers will
wait 15 minutes only.

11
TC-HDMIW30_manual_en.doc
LEGAL DISCLAIMER: Because we are committed to improving our products, the details above
may change without prior warning. This User Manual is published without warranty and any
improvements or changes to the User Manual necessitated by typographical errors, inaccuracies
of current information, or improvements to programs and/or equipment, may be made at any
time and without notice. Such changes will be incorporated into new editions of the User
Manual.