visplay Mono 20 P/L User manual

play it smart
Mono 20 P/L
Assembly and operating instructions
USA & CANADA


Mono20P/L
1/2019 (US)
Table of Contents
1 Safety .......................................................... 3
1.1 Explanation of symbols ...........................................3
1.2 Intended use ............................................................3
1.3 Fundamental dangers.............................................3
2 Product description ...................................... 3
2.1 Overview..................................................................3
2.2 Brief description.......................................................3
2.3 Scope of supply and accessories........................... 4
3 Assembly.......................................................5
3.1 Unpacking ...............................................................5
3.2 Requirements of installation location......................5
3.3 Reinforcing of panels...............................................5
3.4 Mounting..................................................................5
3.5 Visplay plug system................................................ 7
4 Operation..................................................... 8
4.1 Attaching merchandise support..............................8
4.2 Removing merchandise support .............................8
4.3 Cleaning...................................................................8
5 Dismantling and disposal............................. 8
5.1 Dismantling ..............................................................8
5.2 Disposal....................................................................8
6 Technical data .............................................. 9
6.1 Dimensions.............................................................. 9
6.2 Connected loads ................................................... 10
6.3 Load values............................................................ 10
These instructions facilitate the safe and eective use
of the “Mono20P/L” product.
These instructions are part of the product and must be
kept safely and in easy reach from the product at all
times.
All persons who use or handle this product must have
read these instructions. Observance of all the safety and
handling instructions given in these instructions are a
prerequisite for safe working.
The figures in these instructions serve for general
understanding and may dier from the actual version.
All dimensions in these instructions are given in
millimeters and inches.
Quality assurance
All processes in our company are subject to a compre-
hensive management system, which conforms to the
quality standard ISO 9001 and the environmental
standard ISO14001.
The management system is regularly inspected by the
Zertifizierungs- und Umweltgutachter GmbH (BSI),
which documents conformance to the standards by a
certificate.
Copyright
These instructions are protected by copyright. Their use
is permitted within the scope of use of the product. Any
use over and above this is only permitted with the written
approval of the manufacturer.
Our General Terms and Conditions of Sale and Supply
are valid for all orders.
Mono 20 P/L is approved by the Underwriter
Laboratories Inc.


Mono20P/L
1/2019 (US)
1 Safety
1.1 Explanation of symbols
Safety instructions are marked as follows in these instruc-
tions.
⚠WARNING
A safety instruction marked in this manner indi-
cates a possible dangerous situation, which if not
prevented may result in death or severe injury.
⚠NOTE
A safety instruction marked in this manner indi-
cates a possible dangerous situation, which if not
prevented may result in damage to property and
the environment.
1.2 Intended use
The product is used exclusively for mounting merchandise
supports, on which goods are presented. Merchandise
supports permitted for this purpose are exclusively those
that conform to the specification in these instructions.
Field of application
The product must be used exclusively in the commercial
field.
Personnel
These instructions describe the assembly of the holder
set as well as its handling and cleaning. Therefore these
instructions must be handed on to the end user after
assembly of the holder set.
The contents of the section on “Assembly” is directed at
personnel, who undertake the assembly of the holder
sets (e.g. shop fitters).
The contents of the section on “Handling” is directed at
the end users (e.g. sales personnel, visual merchandisers).
⚠WARNING
In the event of misuse, there is a danger that the
merchandise supports will be damaged or fall. This
may lead to injury and damage to the product.
>Use only approved accessories.
>Comply with the maximum permitted load values.
>Do not lean any ladders against the merchan-
dise supports.
1.3 Fundamental dangers
⚠WARNING
>Do not load the merchandise supports above the
maximum load capacity.
>Do not place any receptacles, from which fluids
can escape, on the merchandise supports.
>Keep moisture away from current conducting
components.
2 Product description
2.1 Overview
Mono20P/L is a support system that can be selectively
aligned for mounting display supports on which products
are presented.
2
1
Fig. 1: Mono 20 P/L
2.2 Brief description
Contained in the electrified Mono 20 P/L holder set
(Fig. 1/1) is a power element, through which low voltage
power can flow. This allows the use of shelves (Fig. 1/2)
with integrated light fittings for additional illumination of
the positioned goods.
The merchandise supports must be obtained from the
manufacturer. The electrical devices must conform to the
specification given in these instructions. One merchandi-
se support can be hung per holder set.
Holder sets
The holder sets serve for mounting of the merchandise
support. They are available in the following versions:
• Mono20P/L holder set with power cable, electrified
(Fig. 2/A) with separate cover clip.
• Mono20P/L holder set , non-electrified (Fig. 2/B),
with separate cover clip.
• Mono20P/L light holder set with power cable,
electrified (Fig. 2/C) with separate cover clip.
• Mono20P/L light holder set , non-electrified
(Fig. 2/D), with separate cover clip.
NOTE! Non-electrified merchandise supports can
be pushed into electrified holder sets without
anyproblems.
For the holder mounting in wood see section 3.4.1 on
page 6.
A B C D
Fig. 2: Version of the various holder sets


Mono20P/L
1/2019 (US)
Power supply
The power element integrated in the holder set is
supplied with power from a converter. This converts the
mains power from 120 –240 V AC to 24 V DC.
120 V
L = 1500 mm / 59.055"
NV (24 V)
L = 500 mm / 19.685"
ø 7.7 mm
0.303"
Fig. 3: Converter 24 V
NOTE! The dimmer set 318-271.19 is required for the
use of dimmers!
For an overview of the electrical connection of the holder
sets and the associated components see the section on
Electrification 3.5 on page 7.
2.3 Scope of supply and accessories
2.3.1 Electrical connection set
The electrical connection set is a standard part of the
electrified holder set. It serves for retrospective electrical
connection of existing non-electrified Mono 20P/L holder
sets.
Included in the electrical connection set is the electrical
connection with the power cable (Fig. 4/1) and 2 counter-
sunk fixing screws M5 x 16 Torx (Fig. 4/2).
1
2
Fig. 4: Electrical connection set for non-electrified holder sets
For mounting the electrical connection set see section
3.4.2 on page 6
2.3.2 Cover clip
Fig. 5: Cover clip
The cover clip must be ordered separately.
2.3.3 Merchandise supports
The merchandise supports are used for displaying goods.
Merchandise supports can have dierent shapes.
Examples of merchandise supports available:
• Hanging arms, straight
• Shoe shelves
-for a single shoe or a pair
-electrified or non-electrified
• Mounting bracket for wooden or glass shelf
• Support bar in connection with mounting bracket
• Single support bar
Further information on the individual merchandise sup-
ports as well as the specific product descriptions can be
found in the product catalogue.
Mounting brackets and shelves
Mounting brackets are for mounting support bars orshel-
ves.
Shelves are trays or racks made of wood or glass. Dra-
wings for producing shelves suitable for standard moun-
ting brackets can be obtained from the manufacturer.
2.3.4 Hanger sets for wooden panels, etc.
2
1
Fig. 6: Hanger sets for wooden panels
Instead of merchandise supports, wooden panels and
placards, etc., can be fixed in the holder set with a
hanger set. This consists of hanger adapter (Fig. 6/1) and
hanger bracket (Fig. 6/2).
• Maximum load: 20 kg 44 lbs


Mono20P/L
1/2019 (US)
3 Assembly
⚠WARNING
The system can fail if assembly is not carried out
correctly or the base cannot support the necessary
load. There is a danger of injury from goods or
merchandise supports falling down.
>Note and comply with all the following instruc-
tions on assembly.
>Make sure that the base is suitable for the ex-
pected loads.
3.1 Unpacking
Immediately on receipt, check the delivery is complete
and intact.
If transport damage is noted, proceed as follows:
• Do not accept delivery or only under reservation.
• Make a note of the extent of the damage on the trans-
port documents or the delivery note of the transport
company.
• Initiate a complaint.
Packaging
The product is securely packed so that transport damage
is unlikely.
• Store original packaging for subsequent transport.
• Only send product in original packaging.
• Take note of all instructions which are given on the
packaging.
Disposing of packaging materials
If the packaging materials are no longer required, dis-
pose of them according to local disposal regulations.
3.2 Requirements of installation location
The installation location must comply with the following
requirements:
• The installation location must be dry. Construction
outdoors is not permitted.
• The base (walls, columns, etc.) must be designed for
and able to support the loads to be borne.
• The base must be level in order that the holder sets are
fully supported after mounting.
3.3 Reinforcing of panels
The panels, in which the holder sets are mounted, must
be reinforced. Otherwise the panels, together with the
mounted holder sets, may buckle andbreak.
A B
c
a
bc
a
d
a
b
c
d
min. 60
min. 22
19
min. 28.5
min. 2.362
min. 0.866
0.748
min. 1.122
mm in
Fig. 7: Back panel reinforcement
Possible reinforcements:
• Angle sections (Fig. 7/A). Take note of the dierent
heights of the holder sets (whether electrified or
non-electrified).
• Wooden ribs (Fig. 7/B)
• Screw reinforcement on to the rear side of the panels
and additionally glue wooden ribs. Make sure that the
panels are supported evenly.
3.4 Mounting
⚠WARNING
If fixing points are left out, the load carrying
capacity of the holder sets provided for will not be
achieved.
>Use all fixing points of the holder sets.
>Ensure the correct alignment of the holder sets.
Fig. 8: Correct alignment of the holder sets
The fixing points, on which the holder sets are to be
screwed, are prepared. The holder set is marked on the
rear side with an arrow and the marking “UP” (Fig. 8).


Mono20P/L
1/2019 (US)
3.4.1 Mounting holder set on wood
When using the fixings supplied, the holder set must only
be mounted on wooden panels that are 19 mm 0.630”
thick.
The holder sets can be used both with or without the
cover clip. Pay attention to the dierent milled form.
A B
Fig. 9: Milled form without (a) and with cover clip (B)
Mounting for the non-electrified holder sets (Fig. 10/A)
is identical to mounting for the electrified holder sets
(Fig. 10/B).
1. Arrange for wooden panels with a milled form
(see 6.1 on page 9) to be fabricated by a specialist
works.
2
1
A B
2
1
Fig. 10: Mounting on wooden panel
2. Apply holder set (Fig. 10/1).
3. Screw the wood screws (Fig. 10/2), through the holes
provided in the holder set, into the panel and tighten
to 3 Nm.
ÂThe holder set is fixed.
Attaching cover clip
If the version with cover clip has been selected, the cover
clip must finally be attached after mounting the holder
set.
1
2
Fig. 11: Attaching cover clip
• Place the cover clip (Fig. 11/1) on the holder set
(Fig. 11/2).
3.4.2 Holder sets to be retrospectively electrified
By using the electrical connection set 332-259.19, a non-
electrified holder set (Fig. 12/A) can be retrospectively
electrified (Fig. 12/B). The holder set does not need to be
dismantled from the wooden panel for this procedure.
Access to the back of the panel, however, must be
ensured.
A B
Fig. 12: Holder set, non-electrified (A) and electrified (B)
Removing cover panel
1
3
2
4
Fig. 13: Unscrewing cover panel
1. Loosen both screws (Fig. 13/1) with a Torx screwdriver.
The screws and cover panel (Fig. 13/2) are no longer
required and can be disposed of.
2. Fix the electrical connection set (Fig. 13/3) with the
supplied countersunk screws (Fig. 13/4) to the holder
set.
ÂThe holder set is electrified and can now be
connected to the power supply.


Mono20P/L
1/2019 (US)
1 Extension cable 24 V
2 90 W LED converter
3 24 V distributor, 6 way - optional
Powering with 90 W converter
3.5 Visplay plug system
⚠NOTE
It is imperative to take account of power consump-
tion of the electrical devices! The maximum power
consumption should be 10% below the nominal
output rating of the converter.
1
2
12 2
2 3
1


Mono20P/L
1/2019 (US)
4 Operation
⚠WARNING
Injury can be caused and the merchandise supports
and/or system can be damaged if the maximum
load of the merchandise supports is exceeded.
>Observe the maximum load values of the
individual merchandise supports.
>Do not exceed the maximum load of
40kg 88lbs per holder set.
4.1 Attaching merchandise support
To insert the merchandise support, proceed as follows.
1 2
Fig. 14: Inserting merchandise support
1. Feed the merchandise support with a slight upward
angle into the hole of the holder set up to the stop
(Fig. 14/1), and then lower (Fig. 14/2).
2. Make sure that the merchandise support is correctly
engaged in the holder set.
ÂThe merchandise support is securely fixed. It has
a slight slope (approx. 1.5°).
3. Place goods evenly on the merchandise support
and ensure that the maximum load is not exceeded.
All load values are inclusive of the weight of the mer-
chandise support.
4.2 Removing merchandise support
To remove the merchandise support, proceed as follows:
1. Remove goods from the merchandise support.
2. If a shelf is used, remove the shelf from the mounting
bracket.
1 2
Fig. 15: Removing merchandise support
3. Slightly lift up the merchandise support/mounting
bracket (Fig. 15/1) and pull away from the holder set
(Fig. 15/2).
ÂThe merchandise support comes away from the
holder set.
4.3 Cleaning
During the course of time, dust and deposits from clothes
hangers can settle on the merchandise supports. In order
that the goods on display do not become soiled, the
merchandise supports must be regularly cleaned.
Fig. 16: Cleaning
1. Remove goods from the merchandise support.
2. Remove dirt on the merchandise support carefully
with a soft, dry cloth (Fig. 16).
3. Remove stubborn dirt with a mild cleaning agent.
5 Dismantling and disposal
5.1 Dismantling
To dismantle the holder set, proceed as follows:
1. Remove goods from the merchandise supports.
2. Remove all merchandise supports (see section 4.2 on
page 8).
1
2
Fig. 17: Levering o cover clip
3. Lever o cover clip (Fig. 17/1) with a small slotted
screwdriver (Fig. 17/2). The cover clip cannot be
reused and must be replaced.
4. Unscrew screws.
5. Take o holder set.
5.2 Disposal
⚠NOTE
If product components are improperly disposed of
they can pose a danger to the environment.
>Ensure product components are disposed of in a
proper environmental manner or through waste
management specialists.
>Send components that can be recycled for recy-
cling.
Disposal rules
Dispose of product components in line with the following
principles:


Mono20P/L
1/2019 (US)
• Send steel for recycling or scrapping.
• Send aluminium for recycling or scrapping.
• Send die cast zinc for recycling or scrapping.
• Send plastics for recycling.
• Dispose of remaining components sorted according to
the type of material.
6 Technical data
6.1 Dimensions
6.1.1 Installed dimensions, holder set
Mono 20 P/L
ed
b
a
ef
c
a
b
c
d
e
f
ø 31.9
60
100
28.5
19
22
1.256
2.362
3.937
1.122
0.748
0.866
mm in
A B
Fig. 18: Mono 20 P/L with power cable(A) / non-electrified (B)
Mono 20 P/L light
Installed dimensions, non-electrified holder set
ed ef
b
a
c
A B
a
b
c
d
e
f
ø 31.9
50
86
28.5
19
22
1.256
1.969
3.386
1.122
0.748
0.866
mm in
Fig. 19: Mono20P/L light with power cable(A) / non-electrified (B)
6.1.2 Milled form for holder set with cover clip
Mono 20 P/L
mm in
a
b
c
d
e
f
g
h
i
j
k
19
6
ø 2.5
ø 32
50
24
22
32.8
35.2
68
90
0.748
0.236
0.098
1.260
1.969
0.945
0.866
1.291
1.386
2.677
3.543
e
ff
ihg
j
k
e
a
b
c d
Fig. 20: Mono20P/L with cover clip
Mono 20 P/L light
e
a
b
c
h
f g
d
mm in
a
b
c
d
e
f
g
h
19
6
ø 2.5
ø 32
38
6
72
53
0.748
0.236
0.098
1.260
1.496
0.236
2.835
2.087
Fig. 21: Milled form for Mono20P/L light with cover clip
6.1.3 Milled form for holder set without cover clip
Mono 20 P/L
mm in
a
b
c
d
e
f
g
h
i
j
k
l
m
19
6
ø 2.5
ø 32
ø 26
15
50
24
22
32.8
35.2
68
90
0.748
0.236
0.098
1.260
1.024
0.591
1.969
0.945
0.866
1.291
1.386
2.677
3.543
e
0
+0.2 0
+0.008
g
hh
kji
l
m
g
a
b
f
c d
Fig. 22: Mono20P/L without cover clip


Mono20P/L
1/2019 (US)
Mono 20 P/L light
g
a
b
c
j
h i
d
e
f
mm in
a
b
c
d
e
f
g
h
i
j
19
6
ø 2.5
ø 32
ø 26
15
38
6
72
53
0.748
0.236
0.098
1.260
1.024
0.591
1.496
0.236
2.835
2.087
0
+0.2 0
+0.008
Fig. 23: Mono20P/L without cover clip
6.1.4 Converter dimensions, power-dependent
LKLE
H
1
H
2
W
L 1
L 2
Fig. 24: Converter dimensions, power-dependent
Specification 90 W
Length [L1] 171 mm
6.732 inches
Length [L2] 161 mm
6.339 inches
Width [W] 37.5 mm
1.476 inches
Height [H1] 63 mm
2.480 inches
Height [H2] 53 mm
2.087 inches
Length - connecting cable to the infeed
[LE]
500 mm
19.685 inches
Length - power cable [LK]1500 mm
59.055 inches
6.2 Connected loads
General
Specification Value Unit
Operating voltage 120–240 V
Frequency 50–60 Hz
Nominal voltage (SELV) 24 V
Nominal current at power connecti-
on, maximum
6 A
Mains side protection class; conver-
ter 90 W
II
Maximum housing temperature
(converter)
75
167
°C
°F
6.3 Load values
The maximum load applies including the dead weight
and the weight of all components.
Holder set
Specification Value Unit
Mono20P/L holder set 40
88.185
kg/
lbs/
holder set
Mono20P/L light holder set 5
11.023
kg/
lbs/
holder set
Merchandise supports
Specification Value Unit
Shoe shelf for one shoe 20
44.092
kg
lbs
Shoe shelf for a pair of shoes 20
44.092
kg
lbs
Universal mounting bracket 20
44.092
kg
lbs
Hanger arm Ø 20 mm 20
44.092
kg
lbs
Single support bar Ø 20 mm 15
33.069
kg
lbs
Mounting bracket for support bar
Ø 20 mm
15
33.069
kg
lbs
Mounting bracket for wooden
or glass shelf
15
33.069
kg
lbs
Mounting bracket for support bar
30 x 15 mm
20
44.092
kg
lbs
Clamping mounting bracket
for glass shelf
10
22.046
kg
lbs
Single mounting bracket Ø 20 mm 15
33.069
kg
lbs
Hanger set for wooden panel 20
44.092
kg
lbs
Mounting bracket for wooden shelf 15
33.069
kg
lbs
Hanger hook Ø 6 mm 2
4.409
kg
lbs
Hanger hook Ø 7.5 mm 2
4.409
kg
lbs
Panel thickness
Specification Value Unit
Thickness of wooden panel, maximum 19
0.748
mm
inches

Visplay Companies
Oces & Showrooms
Visplay Exclusive Dealers / Sales Agents /
Authorized Distributors
Australia
Distributed by MADE Retail Systems
Authorized Distributor
2 Stephenson Street
Cremorne Vic 3121
Melbourne
Australia
T [phone]
[e-mail]
Brazil
Distributed by Instant Shop
Authorized Distributor
Av. Nove de Julho, 5017 # 51
Cj. 51 - 5° Andar
São Paulo, SP - CEP 01407-200
Brazil
T [phone]
[e-mail]
China
Distributed by Okamura Shanghai
Authorized Distributor
15Fax: B block, FutureLand building
No.5 Lane 388, Zhongjiang Road
Putuo District
Shanghai 200062
China
T [phone]
[e-mail]
Greece
Distributed by KYVERNITIS I. SA
Exclusive Dealer
125, G. Papandreou & Adrianiou str.
144 51 Metamorfosi Athens
Greek
T [phone]
[e-mail]
India
Distributed by
Matrix Visual Innovations Pvt. Ltd.
Authorized Distributor
45/1, 2nd Floor, Corner Market,
Malviya Nagar
New Delhi 110017
India
T [phone]
[e-mail]
Italy
Distributed by Zeppelin s.r.l.
Exclusive Dealer
Via Matteucci, 2
61032 Fano PU
Italy
T [phone]
[e-mail]
Japan
Distributed by
Okamura Corporation
Exclusive Dealer
Higashi Ote Bldg.,
1F1-1-7, Uchikanda, Chiyoda-ku
Tokyo 101-0047
Japan
T [phone]
[email protected]
Panama
Distributed by Vidisplay S.A.
Authorized Distributor
Calle Ramon Jurado,
Paitilla Mall, Local 17 Piso 1
Punta Paitilla
Panama
Ciudad de Panamá
T [phone]
[e-mail]
Poland, Czech Republic & Baltics
Distributed by
Meškank Interior Brands
Sales Agent
T [phone]
[e-mail]
Russia
Distributed by ULTIMATHULE
Exclusive Dealer
Business quartel „ARMA“
Nizhniy Susalniy per., 5 bld.18
105065 Moscow
Russia
T [phone]
[email protected]
Saudi Arabia
Distributed by Saudi TKT
Authorized Distributor
P.O. Box 10700
Jeddah 21443
Saudi Arabia
T [phone]
[e-mail]
Turkey
Distributed by
Dekotek Mimarlık Ltd. Sti
Exclusive Dealer
Sair Nigar Sokak 80/8 Osmanbey
34363 Istanbul
Turkey
T [phone]
[e-mail]
For other countries:
Visplay GmbH
Charles-Eames-Str. 2
79576 Weil am Rhein
T [phone]
[e-mail]
Austria
Visplay Austria
Schottenring 12
1010 Wien
Austria
T [phone]
[e-mail]
Belgium
Visplay Belgium
Woluwelaan 137
1831 Diegem
Belgium
T [phone]
[e-mail]
France
Visplay France
So Square Opéra
5, Rue Boudreau
75009 Paris
France
T [phone]
[e-mail]
Germany
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Germany Showroom
Visplay GmbH
Charles-Eames-Strasse 2
79576 Weil am Rhein
Germany
T [phone]
[e-mail]
Netherlands
Visplay Netherlands
De Oude Molen 2
1184 VW Ouderkerk aan de Amstel
Netherlands
T [phone]
[e-mail]
Spain /Portugal / Latin America
Visplay Spain
Calle Padilla, 21
28006 Madrid
Spain
T [phone]
[e-mail]
United Arab Emirates
Visplay GmbH (Dubai BR)
Sheikh Zayed Road
P.O. B o x: 2 13 0 3 5
Sheikha Sana Mana
Al Maktoum Building
Oce - M 10
Dubai
T [phone]
[e-mail]
United Kingdom
Visplay United Kingdom
30 Clerkenwell Road
London EC1M 5PG
United Kingdom
T [phone]
[e-mail]
USA
Visplay Inc.
7528 Walker Way
Allentown, PA 18106
USA
T [phone]
[e-mail]