Visual Comfort & Co. Lafayette NW 2707 User manual

1. Carefully remove all parts from the box.
2. Remove the backplate (G) from the metal frame (J) by loosening the side screws (I).
3. Remove the mounting plate (C) from the backplate (G) by loosening the top and bottom
screws (F).
4. Put the mounting plate (C) on the wall and mark the holes position with pencil.
5. Drill 4 holes on the wall and knock the anchors (B) into the holes.
6. Affix mounting plate (C) onto the outlet box and secure with mounting screws (E), then
secure the wood screws (D) to the anchors (B) and lock tight.
7. Connect the fixture Ground (bare) wire with the ground wire from the outlet box using
wire nut (A). If your house does not have ground wire, then attach this wire to the
green grounding screw inside of the outlet box.
IT IS IMPERATIVE THAT THIS FIXTURE BE GROUNDED.
8. Connect the fixture Neutral wire (WHITE) with the neutral wire (White) from the outlet box
using wire nut (A).
9. Connect the fixture Hot wire (BLACK) with the hot wire (Black) from the outlet box using
wire nut (A).
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL
BE COMPROMISED.
10. Attach the backplate (G) to the mounting plate (C) and secure with top and bottom
screws (F).
Lafayette Large 1/2 Wall Lantern
Item # NW 2707
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING***SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY
DAMAGE OR OBVIOUS DEFECT. DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
NOTE: CAREFULLY UNPACK EACH PIECE IN TOP LAYER OF PACKING PRIOR TO
REMOVING. RETAIN ALL PACKING MATERIAL UNTIL INSPECTION AND
INSTALLATION ARE FINAL.
WET
L
I
S
T
E
D
C
US
Intertek
CM
TO assemble safety cables:
1.Join fixture safety cables with safety
cable from wall.
2.Wrap both safety cable around the
cable lock nut.
3.Insert screws into both holes on cable
lock nut,secure screws with screwdriver.
4.Push the cable lock nut into outlet box.
Safety cable
Cable lock nut

11. Hang the reflector (H) to the backplate (G).
12. Attach the glass panels (K & L) on the frame and secure by bending the metal tabs.
13. Insert bulbs (not included) into the sockets.
14. Attach the metal frame (J) to the backplate (G) and secure with side screws (I).
15. Installation is complete, turn on power at fuse or circuit breaker.
***Clean with a dry, soft cloth only. Use no harsh abrasives or chemical agents.
Lafayette Large 1/2 Wall Lantern
Item # NW 2707
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING***SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY
DAMAGE OR OBVIOUS DEFECT. DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
NOTE: CAREFULLY UNPACK EACH PIECE IN TOP LAYER OF PACKING PRIOR TO
REMOVING. RETAIN ALL PACKING MATERIAL UNTIL INSPECTION AND
INSTALLATION ARE FINAL.
WET
L
I
S
T
E
D
C
US
Intertek
CM
TO assemble safety cables:
1.Join fixture safety cables with safety
cable from wall.
2.Wrap both safety cable around the
cable lock nut.
3.Insert screws into both holes on cable
lock nut,secure screws with screwdriver.
4.Push the cable lock nut into outlet box.
Safety cable
Cable lock nut