Vita Vibe ASB36-90 User manual

ASB36-90 36" Wide 90" Tall Stall Bar Assembly Guide
TM
Please read this guide thoroughly before begi i g
assembly a d follow each process step by step.
Note: Some steps may require two people.
Tools required for assembly a d i stallatio :
9/16" a d 1/2" Wre ch or Socket Wre ch
Tape Measure
Power Drill with 7/32" Drill Bit
Stud fi der (for wood stud mou ti g)

VITA VIBE
ASB36-90
36" Wide 90" Tall Stall Bar Bar Carton Contents.
A - 90" Stall Bar Upright Bea s with Rung Saddles & Hardware (Qty. 2)
B - Stall Bar Wall Mount Standoff Brackets (Qty. 4)
C - 1-1/2" Dia. Hardwood Ash Rungs (Qty. 10)
D - 5/16 x 2-1/2" Lag Bolt with Flat Washer (Qty. 8)
E - Decorative Bolt Head Cover Caps (Qty. 8)
F - Spacer Block (Qty. 1)
A
B
C
D
E
Note: Some hardware items may include
additional pieces and are considered spares.
F
Spacer Block

STEP 1
STEP 2
Attach the four wall mount standoff brackets (B) to the two upright beams (A) as shown by removing the pre-installed
acorn nuts and washers then placing the smaller side of the standoff bracket over the threaded bolts and re-installing
the washers and acorn nuts. DO OT TIGHTE UTS YET.
Measure 12" from the TOP end of the upright beam to the standoff bracket as shown below then securely tighten nuts.
Measure 17" from the BOTTOM end of the upright beam to the standoff as shown below then securely tighten nuts.
Attach the top rung (C)
Lay the two upright beams on the floor 32" apart. Loosen the acorn nuts on the top rung saddles enough to
insert the first wood rung. Position this wood rung under the top saddles locating the saddle between the
laser marks on each end of the rung making sure logo name is on the correct side. DO OT TIGHTE YET.
Measure 8-1/2" from the TOP of the upright beam to the CE TER of the wood rung as shown below.
Securely tighten saddle nuts.
STEP 3
TOP
12"
Acorn ut
Split Lock Washer
Flat Washer
Standoff Bracket
Upright Beam
TOP
17"
ASB36903
TOP
8-1/2"
8-1/2"
Attach the balance of rungs (C)
Once the top rung is in the correct position and securely tightened, begin attaching the rest of the rungs
working from the top to the bottom. Again, loosen the acorn nuts at each saddle enough to insert the wood
rungs. Position the wood rung under the saddles and locate the saddle between the laser marks at each
end of each rung. DO OT TIGHTE YET. Use the supplied wood spacer block (F) to evenly space the
balance of the rungs by placing this spacer between the rungs as shown above. Once you have the rungs
spaced out you can then securely tighten the saddle nuts. ote: These instructions are for evenly spaced
rungs (8-1/2" center spacing) you can space the rungs to your desired location if you prefer.
Laser Marks
Standoff Bracket
Saddle
Spacer Block
Place the spacer block (F) at both sides
when tightening saddle nuts.
Spacer Block
Logo name on this side
(facing the floor)

ASB36904
Mounting the assembled stall bar.
If assembled correctly, the all mount standoff brackets ill be spaced 32" apart allo ing it to mount to standard
ood all studs that are typically spaced 16" on center. once you have located your ood studs and ith the help
of another person, stand the stall bar up against the all and mark the spots here the stall bar ill be bolted to
the ood studs. Pilot drill these eight locations ith a 7/32" drill bit. NOTE: If you are not experienced in doing
this type of ork you may ant to consult a handyperson or professional for help. There is the possibility of
utilities ithin the all that you ill ant to avoid.
Securely fasten stall bar to the all ith the supplied 5/16" x 2-1/2" lag bolts and ashers (D)
If mounting to a metal stud all you ill need to first mount ood blocking spanning at least 3 studs for both
upper and lo er all mount brackets. If mounting to a concrete or masonry all you ill first need to install
lag shield anchors or other type of 5/16" min. anchor bolts. After all bolts are installed push on the supplied
decorative bolt head cover caps (E) If mounting to a metal stud all, you ill need to securely attach t o
backer / blocking boards to the metal stud all then attach the stall bar as described above.
STEP 4 (Final)
To keep you ne stall bar in top condition you may periodically treat the ood rungs ith a light coat of Danish oil
or Linseed oil. Typically t ice a year ill suffice. Before each use please make sure all fasteners are tight and secure.
Vita Vibe, Inc. 40 Ell ood Ct. Greenville, SC 29607
Tel: [phone] Fax: [phone]
Email: [e-mail]
Please keep this assembly guide for future reference. Should you need assistance
ith assembly or replacement parts contact us directly. Do not return to place of purchase.
Made in USA
DISCLAIMER: As with any fitness or exercise equipment, use of this
equipment shoul only be use by persons who are physically able to
use the equipment as it is esigne for. Proper safety gear such as
pa e mats, shoes, clothing an the like shoul always be use .
This equipment shoul not be use alone. Always have someone
nearby in case of an emergency. Vita Vibe, Inc. an it's affiliates will
not be liable for any injury or eath resulting from use of this equipment.
User assumes responsibility for proper assembly, maintenance an
use of this equipment.