Vita Vibe PRODIGY Series User manual

Thank you for choosing Vita Vibe.
We strive to provide the best products possible
by using only the highest quality materials and
workmanship and back it with our exclusive
10 year warranty.
Please keep in mind that your new Vita Vibe
ballet barre is of a modular design allowing you to
customize it in many ways. You can at any time
order additional horizontal barres to convert a single
barre to a double barre or purchase longer or shorter
horizontal barres to better t your needs. The
possibilities are many.
Additional barres, feet, clamps, and other
components can be ordered online or by
calling us at 864-288-8934.
Vita Vibe also manufactures a complete line of wall
and oor mounted ballet barres.
Please visit www.vitavibe.com for more information.
Please keep this guide for future reference.
Should you have a warranty claim or any questions
about this product, please call 864-288-8934.
Do not return to place of purchase.
Portable
Freestanding
Ballet Barres
Assembly Guide
40 Ellwood Court
Greenville, SC 29607
Tel: [phone]
Fax: [phone]
Email: get[email protected]
www.vitavibe.com
DISCLAIMER: As with any therapy, tness, or
exercise equipment, use of this equipment should
only be used by persons who are physically able to
use the equipment as it is designed for.
Proper safety gear such as padded mats, shoes,
clothing and the like should always be used.
This equipment should not be used alone. Always
have someone nearby in case of an emergency.
Vita Vibe, Inc. and it’s afliates will not be liable
for any injury or death resulting from use of this
equipment.
User assumes responsibility for proper assembly,
maintenance, placement and use of this equipment.
WARNING: Make certain all clamps, fittings and
hardware are securely
tightened before each use,
transporting or moving this equipment.
freestanding ballet barre guide(rev. oct12014).indd 1 10/31/2014 10:17:10 AM
Freestanding ballet barres are intended for use
in keeping balance during ballet exercises.
They are not intended to hold one's weight
especially when pushing or pulling against the
barre. The barre should not be used as a crutch.
In ballet, learning to use a freestanding barre
without it tipping over is a benefit as it helps to
improve one's balance and strengthen one's core.

pRODIGY Ser ies PROFESSIONAL Series EXTREME Ser ies
1) Loosen the clamp knob on the foot assembly and
insert the upright leg into the clamp making sure that
the upright leg is vertical and centered on the foot
assembly. Tighten both clamp knobs. Repeat this for
both foot assemblies.
2) Slide one clamp (single barre) or two clamps
(double barre) onto the top of each upright leg and
insert the end of the horizontal barre(s) into the clamp
on each side. Adjust to the desired height and tighten
all clamp knobs securely.
3) For ease of storage, loosen the upper clamp knob at
the bottom of each upright (on the foot assembly) and
pivot the foot so that it is parallel with the horizontal
barre.
4) Before each use make certain all clamps are rmly
tightened.
1) Insert the vertical bars fully into the feet assembly
clamps and firmly tighten set screws with supplied
tool making sure the upper barre clamps are 90
degrees of the foot assembly.
2) Insert the horizontal barre(s) into the indexing
clamps up to the line shown at each end of the barres.
Note: you may need to back out the hex set screws to
allow the barres to enter the clamps. Once you have the
barres inserted into the clamps rmly tighten the hex set
screws with the supplied tool.
3) To adjust the barres to your desired height, simply
loosen the lever on the indexing clamps two or three
turns, pull the indexing plungers and raise or lower the
barres to your selected height. Make sure the indexing
plungers are fully engaged then rmly tighten the clamp
levers. If working alone, you may need to raise or lower
each side incrementally to your desired height.
4) Before each use make certain all clamps are rmly
tightened.
1) Insert the vertical bars fully into the feet assembly
clamps and rmly tighten set screws with supplied
tool making sure the upper barre clamps are 90
degrees of the foot assembly.
2) Insert the two horizontal barres into the clamps of
ONE side of the vertical bars and rmly tighten the set
screws with supplied tool.
3) Insert the two horizontal barres into the clamps on
the other vertical bar and firmly tighten set screws
with supplied tool.
(This step may require the help
of another person depending on the barre length)
4) Before each use make certain all set screws are
securely tightened.
Horizontal Barres Horizontal Barres
Horizontal Barres
Upright Barre (Leg)
Upright Barre (Leg)
Upright Barre (Leg)
Center Support
Assembly for 10 &
12 Foot Barres only
Barre Clamp Height Adjust Indexing Clamp
“T”Clamp
Foot Assembly Foot Assembly
Foot Assembly
Indexing
Track
Capped
Ends Up Insert Barre Into Clamp only to Line
Double Barre Shown Double Barre Shown Double Barre Shown
freestanding ballet barre guide(rev. oct12014).indd 2 10/31/2014 10:17:11 AM
Foot Assembly
Upright Barre(Leg)
Barre Clamp
Horizontal Barre
5) Note: For barres over 8ft you will use the center leg
assembly. Follow step 3 for attachment procedure.
Capped Ends Up
Indexing Clamp "T" Clamp
Insert Barre into Clamp only to Line
Indexing Upright
Horizontal Barres
Upright Barre(Leg)
Foot Assembly
Horizontal Barres
Upright Barre (Leg)
Foot Assembly