Vitek VTD-TTD30R2V User manual

VITEK
VITEK
FEATURES
• 1/3” 2.1 Megapixel Progressive Scan CMOS image sensor
• 2.1 MegaPixel Video Transmission over COAX cable at
distances of up to 1500’ using HD-TVI Technology*
• 2.8~12mm Varifocal Lens
• 30 Infrared LED’s with 100’ IR Range
• Digital Wide Dynamic Range (D-WDR)
• True Mechanical Day/Night function by ICR
• 3D-DNR Noise Reduction
• IP66 Weather Resistance
• 12VDC Operation
VTD-TTD30R2V
2.1 Megapixel Vandal Resistant
HD-TVI IR Dome Camera

2 3
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
To prevent electrical shock and risk of fire hazards, do not expose this unit
to rain or moisture and only use specified power source..
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power interruptions, it is
recommended that the device be powered from an uninterruptible power supply
(UPS).
The symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.

3
3
4
5
6
7
8
1
2
Components and Accessories
Overview
Camera
User Manual
Drill Template
Screws
Hex Wrench
Lower Dome
Lens
Video Cable
Power Cable
Focus
Zoom
Lock Screw
Mounting Base
1
2
3
4
5
6
7
8

4 5
Video Connection
Power Connection
Monitor
Video
Power
12VDC
Connect the power connecter to a 12 VDC power adaptor.
Connect the video connecter to a BNC patch cable.

5
Installation
Before starting, please make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting
steps are as follows:
1. Loosen the screws to
open the lower dome
and then loosen the
lock screw to remove
the mounting base.
2. Attach the drill template to
the place where you want to
install the camera, then drill
4 screw holes and 1 cable
hole (if you want to route the
cables through the mounting
base) according to the drill
template.
3. Route the cables and
connect the power & video
cables, then secure the
mounting base to the ceiling
or wall with screws.
Lock Screw

6 7
Installation
4. Install the camera to the mounting base with the lock screw.
5. Adjust the Three-axis camer
bracket to obtain the optimi-
um viewing angle.
6. Adjust the Focus and Zoom
screw to achieve a clear
image.
7. Install the dome bubble on
the camera with the screws,
then carefully remove the
protective film to complete
the installation.
Zoom
Focus
Tilt 0°~75°
Pan 0°~360°
Rotation 0°~360°

7
Detailed Specifications
Image Sensor
Video Compression
Resolution
Effective Pixels
Signal System
Synchronization
Lens
S/R Ratio
Auto Gain Control
Min Illumination
IR LEDs
IR Distance
Color-B/W Auto Switch
Electronic Shutter
White Balance
WB Range
ICR
BLC
WDR
Transmission Distance
Noise Reduction
Video Output
Weather Resistance
Power Supply
working Environment
Weight
Dimensions
1/3” CMOS (AR0330 + NVR2421 + TP2801)
Standard H.264
1080P (2 MegaPixel)
1920(H) x 1080(V)
PAL/NTSC
Internal
2.8~12mm (Vari-Focal)
>52dB (AGC OFF)
OFF ~44.8dB
0 Lux (LED ON)
30
100’
Yes
1/50s~ 1/67500s
AWB
2300~9600K
Yes
Yes
Digtial WDR
Up to 1500’ (Depending on cable characteristics & integrity)
Yes
BNC × 1
IP66
DC 12V (±10%)
-4~122 / 10%~90% Humidity
34.22 oz. / 2.14 lbs. / 970g
3.10” x 3.58” x 5.70” (78.7 × 90.9 × 144.7mm) H x W x Dia

VITEK
28492 Constellation Road ValenCia, Ca 91355
WWW.ViteKCCtV.CoM
Version 1.0
June 2015
LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants
to the purchaser that products manufactured by VITEK are free of any
rightful claim of infringement or the like, and when used in the manner
intended, will be free of defects in materials and workmanship for a
period of three (3) years, or as otherwise stated above, from the date of
purchase by the end user. This warranty is nontransferable and extends
only to the original buyer or end user customer of a VITEK Authorized
Reseller.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.
The product must not have been tampered with in any way or the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels.
Warranty support is available only if product is purchased through a
VITEK Authorized Reseller.