Vivo MOUNT-ART1 User manual

Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-art1
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
Black Clamp-on Art Easel Stand
SKU: MOUNT-ART1

2 3

STEP 1
STEP 2a
Assemble Upper Clamp  to Base  using M6x10mm Screws  and 4mm Allen Wrench .

To mount the stand to a surface less than 29mm/1.1” thick, mount Lower Clamp  to Upper
Clamp  using M6x12mm Screws  in the bottom two holes with 4mm Allen Wrench
.





DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
 (x1)
Upper Clamp
 (x1)
Lower Clamp
 (x2)
Canvas Clamp
 (x2)
Top Pole
 (x1)
Base
 (x1)
Bottom Pole
 (x1)
Pole Cap
 (x8)
M5x6mm
Screw
 (x3)
M6x10mm
Screw
 (x2)
M6x12mm
Screw
 (x4)
M6x30mm
Screw
(x1)
4mm Allen
Wrench
≤29mm









4 5
STEP 4
Assemble Bottom Pole  to Base  using M6x30mm Screws  and 4mm Allen Wrench .
Ensure the top holes are being used on Bottom Pole 
Depending on the desired height of the mount, assemble one or both Top Poles  to Bottom Pole 
using M5x6mm Screws  and the Phillips end of 4mm Allen Wrench . Insert Pole Cap  into
Top Pole .
STEP 3














≤58.5mm
33-88.5mm
STEP 2b

To mount the stand to a surface more than 29mm/1.1” thick, the Lower Clamp  will need to be
adjusted.
Use 4mm Allen Wrench  to remove the Screw from Clamp  and separate into five parts:
Screw , Washer , Clamp Plate , Bracket , and Hand Screw . Flip Bracket 
upside down as shown below, and then reassemble the Clamp .
*Follow steps below for to mount Lower Clamp (B) to Upper Clamp (A)
based on your specific mounting surface thickness.

To mount the stand to a surface less
than 58.5mm/2.3” thick, mount Lower
Clamp  to Upper Clamp  using
M6x12mm Screws  in the upper
two holes with 4mm Allen Wrench .

To mount the stand to a surface
33-88.5mm/1.3-3.4” thick, mount Lower
Clamp  to Upper Clamp  using
M6x12mm Screws  in the lower two
holes with 4mm Allen Wrench .

 













6 7
Loosen the knobs on the back of Canvas Clamps  and slide them on to the pole assembly, with
one at the top and one at the bottom, as shown below. Secure Canvas Clamps  at the desired
height.

Slide both Canvas Clamps  onto the upper section. This allows smaller canvases to sit
above the desktop surface, if desired.
STEP 5



Secure the mount to the desktop by tightening Lower Clamp . Insert the canvas into Canvas Clamps
 and secure by tightening the front knobs. Adjust the tilt using the lever on the side of Base .
STEP 6

LAST UPDATED: 05/24/2023
REV1.2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 
309-278-5303