Vivo STAND-V038F User manual

Dual Ultrawide Monitor
Desk Stand
Instruction Manual
SKU: STAND-V038F
Assembly Video & Product Info
www.vivo-us.com/products/stand-v038f

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please
contact our product support team at 309-278-5303 or [email protected]om for further assistance. Check carefully to
make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not
use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
LBS
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
We’re Here for You
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
AVG. RESOLUTION TIME (within oice hrs): 5M 4S

3
A (x1)
Pole
B(x1)
Base
S-A (x2)
M6 Cap Nut
M-A (x8)
M4x12mm
Thumbscrew
M-B (x8)
M4x30mm
Screw
M-C (x8)
Spacer
T-A (x1)
3mm Allen Wrench
T-B (x1)
6mm Allen Wrench
F (x1)
Cover
D (x2)
VESA Plate
G (x4)
Arm Cable
Clips
H (x1)
Pole Cable
Clip
E (x1)
Pole Cap
Phillips
Screwdriver Per Arm
C (x1)
Arm
Package Contents
Included Hardware & Tools
Tools Needed: Weight Capacity:
22lbs
(10kg)

4
ASSEMBLY STEPS
STEP 1
STEP 2
Slide Cover (F) and Pole Cable Clips (H) over Pole (A), then thread Pole into Base (B). Press
Pole Cap (E) into the top of Pole. Lock Cover into place by tightening Set Screws using
3mm Allen Wrench (T-A).
Slide Arm (C) onto Pole (A) and secure at desired height using 6mm Allen Wrench (T-B).
Attach Arm Cable Clips (G) onto each arm segment on Arm (C).
E
A
Set Screws
T-A
H
F
T-A
G
C
A
T-B
T-B
B

5
STEP 3
Install VESA Plates (D) onto your monitors using M4x12mm Thumbscrews (M-A) or
M4x30mm Screws (M-B) and Spacers (M-C) if needed. Lightly tighten with a Phillips
screwdriver.
Installation Tip:
The “V” on VESA Plate should
be pointing down towards
bottom edge of monitor.
M-A
M-B
M-C
M-A (x4)
M-B (x4)
M-C (x4)
- OR -
D

6
STEP 4
STEP 5
Slide your monitors with VESA Plate (D) onto Arm (C). Secure the VESA Plates (D) to the
Arm using M6 Cap Nuts (S-A).
Route cables through Arm and Pole Cable Clips (G,H).
WARNING
Do not extend the arms past the base shown below
S-A (x2) S-A
DC
H
G

7
Height
Adjustment
Screw
ADJUSTMENTS
Adjust the tilt joint resistance using 6mm Allen Wrench (T-B).
Remove the M6 Cap Nuts (S-A) and adjust the VESA height adjustment screws using 3mm
Allen Wrench (T-A). Reinstall the M6 Cap Nuts.
T-B
T-B
S-A T-A
T-A

LAST UPDATED: 11/22/23
REV1
v1.0
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
Monday-Friday from 7:00am-7:00pm CST
Need Help? Get In Touch
FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
VIVO-us @vivo_us