Vivo STAND-V004TG User manual

Quad Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v004tg
SKU: STAND-V004TG
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
A (x1)
Pole
B(x1)
Glass Base
C1 (x1)
Monitor Arm
C2 (x1)
Monitor Bracket
D (x1)
Decorative Cover
E (x3)
M6x10 Bolt
F(x6)
Rubber Feet
G (x1)
So Pad
H (x3)
Connecting
Bolt
I(x3)
M8 Washer
J (x4)
M8x10 Bolt
K(x1)
Allen Key Set
L(x2)
Spare Plastic
Cover
M (x16)
M4x12
Thumbscrew
N (x16)
M4x30 Bolt
O(x16)
M4 Spacer
P (x2)
VESA Plate
(Side)
Q(x2)
VESA Plate
(Center)
R (x2)
Security Nut
S (x2)
M4x6 Bolt
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
T (x1)
Wrench
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

3
ASSEMBLY STEPS
STEP 1
Glass Base Installation
Attach Rubber Feet (F) to the underside of the Glass Base (B). Attach So Pad (G) to the Pole (A). Use
a screwdriver to poke holes for screws through the pad. Install Pole to Glass Base using M6x10 Bolts
(E), Connecting Bolts (H) and M8 Washers (I), and tighten with medium Allen Key (K) and screwdriver.
Slide Decorative Cover (D) over the Pole.
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
g
22lbs
(9.98kg)
F
D
G
E
I
H

4
STEP 2
Install Monitor Arm (C1) and Monitor Bracket (C2) to the Pole (A), making sure the wire clips are facing
down. Secure using M8x10 Bolts (J) with a Phillips screwdriver.
c1
c2
STEP 3
OPTION A: Flat Back Monitor
Fasten the VESA Plates (P, Q) to monitors using
M4x12 Thumbscrews (M). Use spacers (O) if
necessary. Do not overtighten; Thumbscrews
only need to be finger-tight.
OPTION B: Curved Back Monitor
Fasten the VESA Plates (P, Q) to monitors using
M4x30 Screws (N) and spacers (O).
J
C1
C2
M
O
O
N
P
P

5
w1
STEP 4
Slide the center monitor onto the center head of Monitor Arm (C1) and Monitor Bracket (C2). Install
the M4x6 bolt (S) to secure the monitor. Slide the side monitors onto the heads of Monitor Arm (C1).
Install the Security Nuts (R) to secure the monitors.
C2 S
R

6
STEP 5
Adjust the tilt and swivel. Remove the plastic cover and use the Allen Key (K) to adjust swivel joint
tension. Remove the plastic cover then use the wrench (T) to tighten the side tilt joints if the monitors
are not fully supported. Tighten the grub screw on back of center monitor joint using small Allen Key
if the monitor is not fully supported.
q
Pry off the
Plastic Cap
T
Grub Screw
K

7
STEP 6
Manage cables for side monitors using the Cable Clips. Cables can also be hidden inside the pole.
STEP 7
Turn the bolt on the center of the monitor arm counter-clockwise using medium Allen Key (K) to
lower the center monitor or clockwise to raise the center monitor. Remove the security nut (R) and
turn the bolt underneath with the small Allen Key (K) to raise or lower the side monitor. Replace the
nut aer adjustment.
p
K

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303