Vivo STAND-V001VA User manual

Single Monitor Desk Mount with
VESA Adapter Bracket
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001va
SKU: STAND-V001VA
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
A (x1)
Pole
B(x1)
Clamp
C(x1)
Swivel Arm
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
J(x1)
Pole Cable
Clip
G (x1)
So Pad
H (x1)
Support Plate
I (x2)
Arm Cable
Clip
D(x1)
VESA Plate
E(x1)
Pole Cap
S-A (x3)
M6x16mm Screw
S-F (x8)
Nut
S-G (x8)
Carriage Bolt
M-A (x4)
M4x12mm
Thumbscrews
M-B (x4)
M4x30mm
Screws
M-C (x4)
Spacers
S-B (x4)
M6x40mm Screw
S-C (x4)
M6x60mm Screw
S-D (x4)
M6x80mm Screw
S-E (x1)
M6 Cap Nut
F (x1)
Grommet Plate
T-C (x1)
6mm Allen
Wrench
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x4)
Bracket Arm
L(x4)
“L” Support
Holder
M(x4)
Plastic Cover
T-D (x1)
Wrench
Alternative mounting hardware (if Bracket Arms are not used)

3
Desk Clamp Installation
Mount Clamp (B) to Pole (A) using M6x16mm Screws (S-A) 3mm Allen Wrench (T-A). Secure assembly
to desktop by tightening knob on Clamp (B).
ASSEMBLY STEPS
STEP 1
STEP 2 (Option A)
TOOLS NEEDED 17.6lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Loosen knob on Clamp (B).
B
T-A
S-A
B
B
A

4
Mount Grommet Plate (F) to Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
Remove adhesive backing from So Pad (G) and adhere to Grommet Plate (F).
If desk does not have an existing grommet hole, drill a 3/8” (10mm) diameter hole at the desired
position through the mounting surface.
Position Pole (A) on the mounting surface and secure
using Knob (B2) and Support Plate (H).
STEP 2 (Option B)
Grommet Installation
Using a phillips screwdriver, remove the screw from Clamp (B) and disassemble. Set Knob (B2) aside.
B
B2
A
F
H
A
B2
G
S-A
T-A

5
Slide Pole Cable Clip (J) and Swivel Arm (C) onto Pole (A). Tighten Swivel Arm (C) at desired height
using 6mm Allen Wrench (T-C). Insert Pole Cap (E) into top of Pole (A). Attach arm Cable Clips (I) onto
Swivel Arm (C).
Attach “L” Support Holders (L) to Bracket Arms (K)
using appropriate M6 Screws (S-B, S-C, or S-D)
for monitor thickness and a Phillips screwdriver.
Do not tighten fully.
Connect VESA Plate (D) to assembled arms using Carriage Bolts (S-G), Nuts (S-F),
Wrench (T-D) and a Phillips screwdriver. Arms can be assembled in one of four
methods, which are shown below and on next page.
STEP 3
STEP 4
STEP 5
E
C
J
T-C
A
I
S-B/C/D
L
K
#1
T-D
D
S-F
S-G

6
STEP 5 (Continued)
#2
#3
#4
T-D
S-F
D
S-G
T-D
S-F
D
S-G
T-D
S-F
D
S-G

7
STEP 6
With all “L” Support Holders (L) facing up, place monitor on lower two holders and fully tighten lower
two screws with a Phillips screwdriver. Turn top holders down and tighten top screws, then tighten
nuts for the upper arms. Install Plastic Covers (M) into “L” Support Holders (L).
STEP 7
STEP 8
Slide monitor assembly onto Swivel Arm (C) and secure with M6 Security Screw (S-E).
Route cables through Arm Cable Clips (I) and Pole Cable Clip (J). Use 5mm Allen Wrench (T-B) to
adjust tilt and swivel on VESA plate head.
S-E
C
IJ
T-B
LM
CAUTION:
To avoid risk of monitors sliding o,
DO NOT rotate monitors beyond +5° or -5°.

LAST UPDATED: 01/16/2023
REV1.2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303