Vivo STAND-SIT1WD User manual

Sit to Stand Single Monitor Wall Mount Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit1wd
SKU: STAND-SIT1WD
[email protected]om www.vivo-us.com 309-278-5303

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected]om, or call us at 309-278-5303.
A (x1)
Wall Bracket
B(x1)
Arm
C(x1)
Smartphone
Tray
D(x1)
Keyboard
Tray
E(x1)
Lower Support
Arm
F (x1)
Upper Support
Arm
G(x1)
VESA Plate
H (x1)
Cable Clip
I (x1)
Cover
J(x1)
Cover
L(x6)
ST4.8x16
K (x2)
M8x25
M (x2)
M5x10
O(x1)
4mm Allen
Wrench
N(x1)
3mm Allen
Wrench
W-A (x3)
Screw
W-C (x3)
Washer
W-B (x3)
Anchor
M-A (x4)
M4x12
P(x1)
6mm Allen
Wrench
M-B (x4)
M5x12
M-C (x4)
D5 Washer

3
ASSEMBLY STEPS
OPTION A: Wood Stud Mounting
Using vertical holes in wall bracket (A) as a guide,
mark drilling locations on wall. Use of a stud
finder is highly recommended. Drill 2.2” (55mm)
deep holes using a 3/16” (4.5mm) drill bit, then
secure the wall bracket using wall screws (W-A)
with washers (W-C).
STEP 1
OPTION B: Concrete Wall Mounting
Using horizontal and lower holes in wall bracket
(A) as a guide, mark drilling locations on wall.
Drill 2.4” (60mm) deep holes using a 3/8” (10mm)
drill bit and press anchors (W-B) into holes, then
secure the wall bracket using wall screws (W-A)
with washers (W-C).
2.2 - 19.8lbs
(1 - 9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver Drill
Pencil
A
X
W- C
W- A
W- C
W-A
W-B
STEP 2
Install covers (I, J) to wall bracket (A).
STEP 3
Insert the lower post of adjustable arm (B) into
the socket in the wall bracket, then secure using
the 3mm Allen wrench (N).
I
J
B
N

4
Assemble smartphone tray (C) to lower support arm using M5x10 screws (M) with a Phillips
screwdriver.
STEP 5
Mount upper support arm (F) to lower support arm using M8x25 bolts (K) and tighten with 6mm Allen
wrench (P).
STEP 7
STEP 4
Remove the knob from the lower support arm (E) to separate into lower support arm (E1) and knob
(E2).
Assemble keyboard tray (D) to lower support arm using ST4.8x16 screws (L) with a Phillips
screwdriver.
STEP 6
E
E2
E1
CM
E1
D
L
P
K
F

5
Place the support arm/tray assembly onto the upper post of the adjustable arm, then secure using the
3mm Allen wrench (N).
STEP 8
Adjust keyboard tray tilt using the 4mm Allen wrench (O). Turn the adjustment screw clockwise to tilt
up to position 1a, and counter-clockwise to tilt down to position 1b. Install the knob (E2) to lock the
position.
STEP 9
N
E2
O
N~
NÄ
N~ NÄ
STEP 10
Install the VESA plates (G) to monitors using M4x12 bolts (M-A) or M5x12 bolts (M-B) with washers
(M-C), making sure the rounded edges of the rear bracket are facing up.
M- C
M-A
M-B
G

6
STEP 11
Place the monitor with VESA plate into the bracket on the upper support arm, then turn the screw on
the bracket to secure the monitor.
STEP 12
Loosen knob in back to adjust monitor height. To adjust gas spring support, turn the hex screw on top
of the rear joint using the 6mm Allen wrench. Counter-clockwise will increase support, and clockwise
will decrease support.
P
N
O

7
STEP 13
Install cable clip (H) to back of upper support arm and remove cable cover from adjustable arm (B).
STEP 14
Organize cables and reinstall cable cover to
adjustable arm.
Adjust as Desired
H
P
O
N
+/-10°
180°
10°
90°
90°

LAST UPDATED: 11/18/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M