Vivo STAND-V202Q User manual

Pneumatic Arm Dual Ultrawide Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v202q
SKU: STAND-V202Q
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x2)
Upper Arm
B(x2)
Lower Arm
C(x2)
VESA Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Base
E(x1)
Upper Clamp
F (x1)
Lower Clamp
G (x1)
Cable Clamp Clip
H (x1)
Grommet Plate
S-B (x5)
M6x10mm Flathead
Screw
S-C (x2)
M6x12mm
Thumbscrew
I(x1)
Support Plate
J(x1)
Knob
K(x4)
Pad
M-A (x8)
M4x12mm Screw
M-B (x8)
M4x16mm Screw
S-A (x1)
Carriage Bolt
M-D(x8)
M6x16mmScrew
M-E(x8)
M6Washer
M-F(x8)
Spacer
T-A (x1)
3mm Allen Wrench
T-B (x1)
4mm Allen Wrench
T-C (x1)
6mm Allen Wrench
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-C (x8)
M6x12mm Screw

3
ASSEMBLY STEPS
2.2-30.9lbs
(1-14kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
Connect Lower Clamp (F) to the front of Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm
Allen Wrench (T-B). For desktops 10-55mm (3/8” to 2 1/4”) thick, use top holes on Upper Clamp. For
desktops 50-85mm (2” to 3 3/8”) thick, use the bottom two holes.
Secure clamp assembly to desktop by tightening the hand bolt. Aix Cable Clamp Clip (G) to the
back of clamp assembly.
Proceed to Step 2 on page 5.
E
D
S-B
T-B
OR
K
D
10-55mm 50-85mm
T-B
S-B
F
E
G
Clamp Installation
Secure Upper Clamp (E) to the underside of Base (D) using M6x10mm Flathead Screws (S-B) and 4mm
Allen Wrench (T-B). Remove adhesive backing and apply Pads (K) to the underside of Base (D).
STEP 1 (Option A)

4
Peel back adhesive backing and apply Pads (K) to underside of Base (D).
S-A
S-B
T-B
H
D
K
D
Place base assembly over grommet hole in desktop and place Support Plate (I) and Knob
(J) on the end of Carriage Bolt (S-A). Tighten Knob (J) to secure.
IS-A
J
Grommet Installation
Insert Carriage Bolt (S-A) into Grommet Plate (H) and secure to underside of Base (D) using M6x10mm
Flathead Screws (S-B) and 4mm Allen Wrench (T-B).
STEP 1 (Option B)

5
STEP 2
Place Lower Arms (B) onto Base (D) and secure by tightening set screws with 3mm Allen Wrench
(T-A). Install Upper Arms (A) on Lower Arms (B) and tighten set screws with 3mm Allen Wrench (T-A)
to secure.
STEP 3
Secure VESA Plates (C) to back of monitors using appropriate Screws (M-A thru M-D), M6 Washers
(M-E), and 6mm Allen Wrench (T-C). Use Spacers (M-F) for curved monitor.
Flat Back Monitors
Curved Monitors
B
D
T-A
A
B
T-A
M-A
M-C
M-B
M-D
M-E
M-E
M-F
- OR -
C
C

6
STEP 4
STEP 5
S-C
Increase Strength - If the arm
does not have enough movement,
turn the adjustment screws counter-
clockwise.
Adjusting Tension Decrease Strength - If the arm
raises up, turn the adjustment
screws clockwise until it holds the
monitor in a horizontal position.
CAUTION
To avoid damage to the monitor
and mount, always keep the arm in
a horizontal position while making
adjustments.
T-C
T-C
Place monitors with VESA Plates (C) onto Upper Arms (A) and secure with M6x12mm Thumbscrews
(S-C).
C
A
While holding Upper Arm (A) in the horizontal position, adjust the gas spring tension using 6mm Allen
Wrench (T-C).
A

7
Cable Management Covers
Adjustments
Lower Arm (B):
1. Slide covers forward to remove.
2. Place cables in covers.
3. Connect inner tabs to clips on arm to
secure in place.
Upper Arm (A):
1. Pull tabs outward on lower portion of covers.
2. Pull upper tabs outward to fully remove covers.
3. Place cables in covers.
4. Re-install by snapping upper tabs in place, then
snap lower tabs on to fully secure.
Adjust monitor placement as desired. Allen Wrenches (T-B, T-C) can be stored in Cable Clamp Clip (G)
for future adjustments.
1
2
1
3
2
34
4
B
B
A
A
270°
360°
180°
360°
90°
-45°
T-C
T-B
G

LAST UPDATED: 11/29/2022
REV1
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303