Vivo STAND-V002M User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002m
SKU: STAND-V002M
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
Arm
B(x1)
Clamp
C(x1)
Pole Cover
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Pole
E(x1)
Cable Clip
F (x1)
Grommet
Base
G (x5)
Rubber Pad
I (x1)
Support Plate
M-A (x8)
M4x12
M-B (x8)
M5x12
J(x1)
5mm Allen Key
K (x1)
6mm Allen Key
M-C (x8)
D5 Washer
H (x1)
Bolt
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Clamp Installation
Stick rubber pads (G) to the underside of clamp (B). Attach pole (D) to clamp (B) using bolt (H). Tighten
using 6mm allen key (K). Attach clamp (B) to desktop.
D C
K
H
G
B
10- 88m m
Install Pole Cover (C) to Pole (D).
17.6 lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

4
STEP 1 (Continued)
OPTION B: Grommet Base Installation
For grommet hole mounting, remove screw in top of bolt on clamp (B). Stick rubber pads (G) to bottom
of grommet base (F). Attach support plate (I) to bolt and run through grommet hole into grommet base
(F) and thread into pole (D) as shown in diagram.
B
G
F
I
10-75mm

5
STEP 2
Slide cable management clip (E) and arm (A) onto pole (D) and tighten using 5mm allen key (J).
J
A
E
D

6
STEP 3
STEP 4
Attach two bolts (M-A or M-B) and washers (M-C) to top mounting holes of monitors, making sure to
leave 3mm of threads exposed. Align bolts (M-A, M-B) in VESA plates. Secure using two more bolts
(M-A or M-B) and washers (M-C) in the bottom two holes. Tighten all eight bolts using phillips screw-
driver.
Adjust tension in monitor bracket with 6mm allen key (K) as shown in diagram.
M- A
M- B
M- C
3
M- A
M- B
M- C
1 2
3m m
+45°
-45°
K

7
STEP 5
Store allen keys (J,K) in cable management clip (E) for future adjustment.
STEP 6
Adjust height of monitors by turning bolt in top of monitor brackets as shown in diagram.
J
K
360°
360°
J

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303