Vivo STAND-HS03B User manual

Black Hand Sanitizer Floor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-hs03b
SKU: STAND-HS03B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
STEP 1
Assemble the lower pole (C) to the
base (B) using the M6x20 bolts (G).
Tighten with the 4mm Allen wrench
(I) and slide the cover (F) down over
the pole.
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
A (x1)
Mounting
Plate
B(x1)
Base
C(x1)
Lower Pole
D (x1)
Upper Pole
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3
YEARS. ADULT SUPERVISION IS REQUIRED.
E (x1)
Pole
Connector
F(x1)
Cover
11lbs
(5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
G (x3)
M6x20
H(x8)
M6x10
I(x1)
4mm Allen
Wrench
J (x3)
ST6.3x55
K (x3)
10x45 Anchor
L(x2)
Adhesive
Pad
M (x2)
M5x18
N(x2)
M5 Nut
O(x1)
Wrench
PencilDrill
Phillips
Screwdriver Drill Bit
STEP 2
OPTION A: Wood Floor Mounting
Place the base (B) on the desired
location and mark drilling points with
a pencil. Drill 2.2” (55mm) deep holes
using a 3/16” (4.5mm) drill bit. Mount
the base to the floor using ST6.3x55
screws (J).
G
CF
I
B

3
STEP 2 (Continued)
OPTION B: Concrete Floor Mounting
Place the base (B) on the desired location and mark drilling
points with a pencil. Drill 2.4” (60mm) deep holes using a 3/8”
(10mm) drill bit and insert 10x45 anchors (K) into the drilled
holes. Mount the base to the floor using ST6.3x55 screws (J).
STEP 3
Insert an M6x10 bolt (H)
into each side of the upper
pole (D) at the first, second
or third locations from the
top, leaving 1/8” (3mm) of
thread exposed between the
bolt heads and pole. Hang
the mounting plate (A) over
the bolts, then secure with
x2 more M6x10 bolts (H).
Tighten with the 4mm Allen
wrench (I).
STEP 4
A
3mm
H
H
STEP 5
OPTION A: Apply adhesive pads (L) to the back of the dispenser, then peel backing and mount the
dispenser to the mounting plate (A).
OPTION B: Insert M5x18 bolts (M) into the slots in the mounting plate (A), then partially screw the M5
nuts (N) onto the M5x18 bolts. Hang the dispenser over the bolt heads, and tighten the M5 nuts using
the wrench (O).
L
2
O
N
M
2- 4m m
1
H
E
D
Assemble the upper pole (D) to
the lower pole (C) using the pole
connector (E) and M6x10 bolts
(H). Tighten with the 4mm Allen
wrench (I).

LAST UPDATED: 09/16/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303